Original record summaries, dates and identifiers for this model-year. Records 101–200 of 1,226, ordered newest first. Dated records on this page: May 7, 2024–May 16, 2025.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 16, 2025Service Bulletin/Repair Instructions
S2323000002 REV.A
NHTSA communication ID: 11018447
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Washer Light On And Will Not Turn Off After Adding Washer Solvent."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Front Drive Unit Vibrates Customers may experience the following: ● Vibration in the front of the vehicle from the front drive unit This bulletin involves replacing the right front output shaft."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission "Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on the following: ● Vehicle enter limp home mode. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Kit For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Front Lower Control Arm Stabilizer Link Noise Customers may experience the following: ● Rattle or clunk noise coming from the front end of the vehicle when driving over bumps, performing turns or during normal operation. This bulletin involves road testing and possibly tightening the stabilizer link attachment to lower control arm nut. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Hard To Fill With Fuel Customers may experience one or more of the following: ● Hard, difficult, or unable to fill the fuel tank. ● Fuel nozzle shuts off prematurely before the fuel tank is full. ● Fuel spits or spills out while filling the fuel tank. This bulletin involves replacing the fuel tank."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Clicking Noise While In 4WD Customers may experience the following: ● Ratcheting, click, or clicking noise in 4WD while turning. This bulletin involves replacing the front driveshaft."
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Clicking Noise While In 4WD ustomers may experience the following: ● Ratcheting, click, or clicking noise in 4WD while turning. his bulletin involves replacing the front driveshaft"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
SWITCH Headlamp Before replacing the Headlamp Switch for faulty dimmer operation. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
ARM Lower Control WHAT: Clunking noise from Front Stabar link to Front Lower Control Arm (FLCA). WHY: The joint is coming loose due to loss of clamp load when there is embedment on FLCA mating surface to the stabar link ball stud. We are currently updating the stabar link design and new design will be implemented in March 2025. HOW: If this Front stabar link to FLCA joint torque is under the residual torque of 70Nm, please retorque the joint to this spec of 110 (Min 70-Max 138). Otherwise proceed with regular diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
ARM Lower Control WHAT: Clunking noise from Front Stabar link to Front Lower Control Arm (FLCA). WHY: The joint is coming loose due to loss of clamp load when there is severe embedment on FLCA mating surface to the stabar link ball stud. We are currently updating the stabar link design and new design will be implemented in March 2025. HOW: If this Front stabar link to FLCA joint torque is under the residual torque of 70Nm, please retorque the joint to this spec of 110 (Min 70-Max 138). Otherwise proceed with regular diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Dual EVAP System Extreme Duty Vapor Canister Filter Kit Customers operating fleet or severe/extreme duty gasoline vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0441 - EVAP Purge System Performance. ● P062A - Fuel Pump Control Performance. Customers may also experience one or more of the following: ● Hard to fill fuel tank with fuel. ● Premature shut-off of the gas nozzle when refueling. ● Flow back of fuel while refueling. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Loss of Power in Reverse Customers may comment on one or more of the following: ● During engine cold start, the vehicle exhibits low torque when shifted into reverse gear. ● Loss of power in reverse gear. This bulletin provides information regarding the loss of engine torque when performing a cold start and immediately shifting into gear"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY BULLETIN D-24-15 announces the addition of the Rear Axle Assembly replacement for 2019 - 2024 RAM 3500 Cab Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT) vehicles to the Powertrain Pre-Authorization program for all dealers (Base, Plus & Premium) to ensure proper repair of Rear Axle Assembly failures and to assist in quality improvements. REV.A
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
TRANSFER CASE Before replacing a transfer case unit for fault codes C1444-98 and/or C1477-4B, be sure to reference TSB 21-048-24 for potential transfer case shift motor replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Kit TSB 21-039-24 REV A - D-Clutch repair kit missing Carrier Output Shaft Seals It has been identified the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Kit TSB 21-039-24 REV A - D-Clutch repair kit missing Carrier Output Shaft Seals It has been identified the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Rear Axle Vibration Shudder Or Chatter Customers may experience the following: ● A chatter, shudder, or vibration from the rear axle during turns. NOTE: This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axle fluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components. NOTE: This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every 3 years or 30,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual. This bulletin involves changing the rear axle lube to possibly address a chatter, shudder or vibration."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Back Glass Water Leak Warranty Extension XL1 The customer may experience one or more of the following: ● A cracked backlite frame Fig. 1 resulting in an interior water leak (crack is visible to the customer). ● Water leak from at top of the backlite. This bulletin involves applying urethane to the sliding backlite."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
After A Recent Service Repair The Vehicle is Setting Diagnostic Trouble Codes (DTCs) B0090-49 Left Frontal Acceleration Sensor-Internal Electronic Failure, B0095- 49 Right Frontal Acceleration Sensor-Internal Electronic Failure