The manufacturer’s record · Page 9 of 9
Original record summaries, dates and identifiers for this model-year. Records 801–824 of 824, ordered newest first. Dated records on this page: Mar 1, 2014–Jan 10, 2019.
Back to 2019 Mazda MAZDA3 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10153313
NHTSA source summary · Original PDF not reviewed by Recallfolio
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.
Source components: ELECTRICAL SYSTEM.
Source record 10153313 at NHTSANHTSA communication ID: 10153312
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak). The concern is most likely the result of the customer not getting the fuel cap completely closed after fueling the vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.
Source components: ENGINE AND ENGINE COOLING.
Source record 10153312 at NHTSANHTSA communication ID: 10153227
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
Source components: SERVICE BRAKES.
Source record 10153227 at NHTSANHTSA communication ID: 10153311
NHTSA source summary · Original PDF not reviewed by Recallfolio
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
Source components: ENGINE AND ENGINE COOLING.
Source record 10153311 at NHTSANHTSA communication ID: 10153310
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.
Source components: ENGINE.
Source record 10153310 at NHTSANHTSA communication ID: 10153332
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.
Source components: EXTERIOR LIGHTING.
Source record 10153332 at NHTSANHTSA communication ID: 10153331
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10153331 at NHTSANHTSA communication ID: 10153330
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active working SAT radio.
Source components: EQUIPMENT.
Source record 10153330 at NHTSANHTSA communication ID: 10153319
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial checkis a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.
Source components: SERVICE BRAKES, AIR.
Source record 10153319 at NHTSANHTSA communication ID: 10153315
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
Source components: SUSPENSION.
Source record 10153315 at NHTSANHTSA communication ID: 10153309
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps):CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery's Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda GR8-1291, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries.
Source components: ELECTRICAL SYSTEM.
Source record 10153309 at NHTSANHTSA communication ID: 10153308
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
Source components: ELECTRICAL SYSTEM.
Source record 10153308 at NHTSANHTSA communication ID: 10154140
NHTSA source summary · Original PDF not reviewed by Recallfolio
1) Center Body Control Module (C-BCM) software concern. The average fuel economy may not be calculated / indicated correctly. 2) Vehicle Control Module (VCM) software concern. The Smart Brake Support (SBS) OFF indicator light may turn on. The personalization menus of i-ACTIVESENSE may not be displayed in the center display. Causal factor: Inappropriate software of C-BCM and VCM.
Source components: ELECTRICAL SYSTEM.
Source record 10154140 at NHTSANHTSA communication ID: 10154139
NHTSA source summary · Original PDF not reviewed by Recallfolio
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?
Source components: STEERING · STRUCTURE:BODY.
Source record 10154139 at NHTSANHTSA communication ID: 10148072
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
Source components: EQUIPMENT · VEHICLE SPEED CONTROL.
Source record 10148072 at NHTSANHTSA communication ID: 10148071
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
Source components: EQUIPMENT · STRUCTURE.
Source record 10148071 at NHTSANHTSA communication ID: 10148070
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10148070 at NHTSANHTSA communication ID: 10148069
NHTSA source summary · Original PDF not reviewed by Recallfolio
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
Source components: SEATS.
Source record 10148069 at NHTSANHTSA communication ID: 10148068
NHTSA source summary · Original PDF not reviewed by Recallfolio
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
Source components: EQUIPMENT · STRUCTURE.
Source record 10148068 at NHTSANHTSA communication ID: 10148003
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.
Source components: EQUIPMENT · SERVICE BRAKES, HYDRAULIC.
Source record 10148003 at NHTSANHTSA communication ID: 10148002
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10148002 at NHTSANHTSA communication ID: 10186263
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA Mobile start (MMS) cannot communicate with vehicle
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10186263 at NHTSANHTSA communication ID: 10148039
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. Software error in TMS 3 (headlight driver module AHL, xenon headlight)"
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10148039 at NHTSANHTSA communication ID: 10148010
NHTSA source summary · Original PDF not reviewed by Recallfolio
ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
Source record 10148010 at NHTSA