The manufacturer’s record · Page 2 of 9
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 824, ordered newest first. Dated records on this page: Dec 5, 2023–Feb 4, 2025.
Back to 2019 Mazda MAZDA3 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 11015004
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 11015004 at NHTSANHTSA communication ID: 11013659
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may notice the front door window(s) do not open. This may be caused by the lower window cable corrosion and damage. To eliminate this concern, the following improvements have been made: The shape of the power window regulator pulley has been modified to prevent cable damage. The shape of the carrier plate has been modified to prevent the cable from being exposed to water/moisture.
Source components: STRUCTURE:BODY.
Source record 11013659 at NHTSANHTSA communication ID: 11013568
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a deformed fuel-filler lid panel (1) attached to the fuel-filler lid box, resulting in a poor appearance. This concern is caused by the lid box not having enough water drainage capability which leads to the accumulation of water inside it. The water then freezes in cold weather and expands or the inner side of the lid panel absorbs the water and swells from long exposure, deforming the lid panel. To eliminate this concern, the shape of the fuel-filler lid box has been modified to have better drainage capability and a modified fuel-filler lid panel service part has been established for less water absorbance.
Source components: STRUCTURE:BODY.
Source record 11013568 at NHTSANHTSA communication ID: 11013654
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
Source components: STEERING.
Source record 11013654 at NHTSANHTSA communication ID: 11013788
NHTSA source summary · Original PDF not reviewed by Recallfolio
Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricted, thereby extending the transmitter battery life. NOTE: Some customers may complain about an engine no start. This may be caused by the customer inadvertently putting the key transmitter in Power Saving Function.
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
Source record 11013788 at NHTSANHTSA communication ID: 11013658
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side)
Source components: SEATS.
Source record 11013658 at NHTSANHTSA communication ID: 11013657
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience that the out-of-area (reception area) type auto lock function sometimes fails. When the front door is being closed with a hand touching one or both of the touch sensors on the front outer handle, the out-of-area (reception area) type auto lock function may fail. Control software of the LF control unit (LFU) has been modified.
Source components: ELECTRICAL SYSTEM.
Source record 11013657 at NHTSANHTSA communication ID: 11012344
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat installed inside of the suspected coolant control valve on certain 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6 and 2020-2023 CX-30 vehicles. The warranty coverage for an applicable repair has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. If you are a recipient of this notice, your vehicle is included in this warranty extension program. What is the problem? On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.
Campaign / software reference: SSPD8
Source components: ENGINE.
Source record 11012344 at NHTSANHTSA communication ID: 11012345
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frequently Asked Questions (FAQ)
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
Source record 11012345 at NHTSANHTSA communication ID: 11011139
NHTSA source summary · Original PDF not reviewed by Recallfolio
A customer may complain of a rattle noise from the right side of the dash. The noise may be coming from the passenger side airbag.
Source components: AIR BAGS.
Source record 11011139 at NHTSANHTSA communication ID: 11011341
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
Campaign / software reference: CSP12
Source components: ENGINE · FUEL/PROPULSION SYSTEM.
Source record 11011341 at NHTSANHTSA communication ID: 11011338
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
Campaign / software reference: CSP12
Source components: ENGINE · FUEL/PROPULSION SYSTEM.
Source record 11011338 at NHTSANHTSA communication ID: 11011336
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
Campaign / software reference: CSP12
Source components: ENGINE · FUEL/PROPULSION SYSTEM.
Source record 11011336 at NHTSANHTSA communication ID: 11011138
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
Source components: UNKNOWN OR OTHER.
Source record 11011138 at NHTSANHTSA communication ID: 11010992
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience rear subwoofer audio sound pauses intermittently at high volume levels. When the volume level is lowered, the subwoofer audio sound resumes. The actual volume level may vary depending on the audio source. If the audio source consists of many low frequency (40 - 70 Hz) sounds, the concern may occur at volume level 35 or higher. This concern may be caused by improper audio amplifier control software. To eliminate this concern, the control software has been modified.
Source components: ELECTRICAL SYSTEM.
Source record 11010992 at NHTSANHTSA communication ID: 11011331
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
Campaign / software reference: CSP12
Source components: ENGINE · FUEL/PROPULSION SYSTEM.
Source record 11011331 at NHTSANHTSA communication ID: 11011137
NHTSA source summary · Original PDF not reviewed by Recallfolio
On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.
Campaign / software reference: SSPD8
Source components: ENGINE.
Source record 11011137 at NHTSANHTSA communication ID: 11011345
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
Campaign / software reference: CSP12
Source components: ENGINE · FUEL/PROPULSION SYSTEM.
Source record 11011345 at NHTSANHTSA communication ID: 11011326
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
Campaign / software reference: CSP12
Source components: ENGINE · FUEL/PROPULSION SYSTEM.
Source record 11011326 at NHTSANHTSA communication ID: 11011141
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
Source components: UNKNOWN OR OTHER.
Source record 11011141 at NHTSANHTSA communication ID: 11011140
NHTSA source summary · Original PDF not reviewed by Recallfolio
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
Source components: ELECTRICAL SYSTEM.
Source record 11011140 at NHTSANHTSA communication ID: 11011133
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.
Source components: ENGINE.
Source record 11011133 at NHTSANHTSA communication ID: 11009665
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.
Campaign / software reference: SSPD8
Source components: ENGINE.
Source record 11009665 at NHTSANHTSA communication ID: 11009664
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.
Campaign / software reference: SSPD8
Source components: ENGINE.
Source record 11009664 at NHTSANHTSA communication ID: 11009654
NHTSA source summary · Original PDF not reviewed by Recallfolio
The SKYACTIV-DRIVE FW6A-EL AT uses “Automatic Transmission Fluid (ATF) Type: FZ”. Only use “ATF-FZ” to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
Source components: POWER TRAIN.
Source record 11009654 at NHTSANHTSA communication ID: 11009644
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
Source components: SERVICE BRAKES.
Source record 11009644 at NHTSANHTSA communication ID: 11009636
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a rear console lid with a sticking feeling or a squeaking noise when opening and/or closing. This is caused by an inappropriate shape of the console lid hinge pin where the position of the hinge pin (1) becomes misaligned when the rear console lid is repeatedly opened and closed. When parts around the hinge pin thermally expand, the result creates a gap in the hinge of the rear console lid.
Source components: UNKNOWN OR OTHER.
Source record 11009636 at NHTSANHTSA communication ID: 11009635
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the rear console lid does not slide smoothly. This may be caused by improperly positioned felt pads attached to the rear console lid lock, which may have moved out of position after repetitive use. The exposed adhesive residue may stick to the rail and disrupt smooth sliding operation.
Source components: UNKNOWN OR OTHER.
Source record 11009635 at NHTSANHTSA communication ID: 11009647
NHTSA source summary · Original PDF not reviewed by Recallfolio
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. Hotline and MASH authorization is not required to order parts for performing this repair. If there are any questions on part ordering or part status, contact the Dealer Assistance Group.
Source components: ENGINE.
Source record 11009647 at NHTSANHTSA communication ID: 11008430
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.
Source components: SERVICE BRAKES.
Source record 11008430 at NHTSANHTSA communication ID: 11008580
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Connect Services - Frequently Asked Questions (FAQ)
Source components: ELECTRICAL SYSTEM.
Source record 11008580 at NHTSANHTSA communication ID: 11008578
NHTSA source summary · Original PDF not reviewed by Recallfolio
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
Source components: ELECTRICAL SYSTEM.
Source record 11008578 at NHTSANHTSA communication ID: 11008577
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about scratches on the instrument cluster lens.
Source components: UNKNOWN OR OTHER.
Source record 11008577 at NHTSANHTSA communication ID: 11008576
NHTSA source summary · Original PDF not reviewed by Recallfolio
Qi Wireless Charger symptom troubleshooting.
Source components: ELECTRICAL SYSTEM.
Source record 11008576 at NHTSANHTSA communication ID: 11008579
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Connect Services - Frequently Asked Questions (FAQ)
Source components: ELECTRICAL SYSTEM.
Source record 11008579 at NHTSANHTSA communication ID: 11008575
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about the Active Driving Display not displaying turn by turn (TBT) travel direction or navigation information.
Source components: ELECTRICAL SYSTEM.
Source record 11008575 at NHTSANHTSA communication ID: 11008573
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
Source components: ELECTRICAL SYSTEM · ENGINE · EXTERIOR LIGHTING.
Source record 11008573 at NHTSANHTSA communication ID: 11008571
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 11008571 at NHTSANHTSA communication ID: 11008429
NHTSA source summary · Original PDF not reviewed by Recallfolio
Symptom 1: Some customers may complain about hearing a grinding noise and/or vibration occur when applying the brake. This is due to rust on the rear brake disc plate. The brake pad has insufficient disc-rust prevention performance, resulting in the disc plate rusting. To eliminate this concern, the pad material has been improved to prevent rust on the disc surface. Symptom 2: Some vehicles may exhibit a squeal noise from the rear brakes when braking lightly while driving at a slow speed. The squeal noise is caused by the disc pad surface fluctuating. To eliminate this concern, the brake pads have been modified.
Source components: SERVICE BRAKES.
Source record 11008429 at NHTSANHTSA communication ID: 11008423
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. BSM system indicates vehicle on the opposite side. i-ACTIVSENSE indicator ring will not turn green Rear Cross Traffic Alert (RCTA) does not work Rear side radar sensor aiming may fail TPMS DTC(s) stored
Source components: LANE DEPARTURE: BLIND SPOT DETECTION.
Source record 11008423 at NHTSANHTSA communication ID: 11006900
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the rear console lid does not slide smoothly. This may be caused by improperly positioned felt pads attached to the rear console lid lock, which may have moved out of position after repetitive use. The exposed adhesive residue may stick to the rail and disrupt smooth sliding operation.
Source components: UNKNOWN OR OTHER.
Source record 11006900 at NHTSANHTSA communication ID: 11006982
NHTSA source summary · Original PDF not reviewed by Recallfolio
Symptom 1: Some customers may complain about hearing a grinding noise and/or vibration occur when applying the brake. This is due to rust on the rear brake disc plate. The brake pad has insufficient disc-rust prevention performance, resulting in the disc plate rusting. To eliminate this concern, the pad material has been improved to prevent rust on the disc surface. Symptom 2: Some vehicles may exhibit a squeal noise from the rear brakes when braking lightly while driving at a slow speed. The squeal noise is caused by the disc pad surface fluctuating.
Source components: SERVICE BRAKES.
Source record 11006982 at NHTSANHTSA communication ID: 11006981
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.
Source components: ENGINE.
Source record 11006981 at NHTSANHTSA communication ID: 11007029
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
Source components: ELECTRICAL SYSTEM.
Source record 11007029 at NHTSANHTSA communication ID: 11006915
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a rattle noise coming from the front suspension while driving the vehicle, with no other driveability concerns. The rattle noise may be caused by a decrease in tightening torque of the two (2) front lower control arm bolts (B) shown in the image below.
Source components: SUSPENSION.
Source record 11006915 at NHTSANHTSA communication ID: 11007009
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
Source components: SERVICE BRAKES.
Source record 11007009 at NHTSANHTSA communication ID: 11007024
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers will report that their fuel door was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-019/21 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2021 Mazda3 and 2020-2021 CX-30 are present.
Source components: FUEL/PROPULSION SYSTEM · STRUCTURE:BODY.
Source record 11007024 at NHTSANHTSA communication ID: 11007022
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
Source components: STRUCTURE:BODY.
Source record 11007022 at NHTSANHTSA communication ID: 11007019
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
Source record 11007019 at NHTSANHTSA communication ID: 11007018
NHTSA source summary · Original PDF not reviewed by Recallfolio
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
Source components: STRUCTURE:BODY.
Source record 11007018 at NHTSANHTSA communication ID: 11007013
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
Source components: UNKNOWN OR OTHER.
Source record 11007013 at NHTSANHTSA communication ID: 11007010
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
Source components: ENGINE · POWER TRAIN.
Source record 11007010 at NHTSANHTSA communication ID: 11006917
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
Source record 11006917 at NHTSANHTSA communication ID: 11006995
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 11006995 at NHTSANHTSA communication ID: 11005671
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: UNKNOWN OR OTHER.
Source record 11005671 at NHTSANHTSA communication ID: 11005706
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules.
Campaign / software reference: SSPC5
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · UNKNOWN OR OTHER.
Source record 11005706 at NHTSANHTSA communication ID: 11005709
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules.
Campaign / software reference: SSPC5
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · UNKNOWN OR OTHER.
Source record 11005709 at NHTSANHTSA communication ID: 11005703
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules.
Campaign / software reference: SSPC5
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · UNKNOWN OR OTHER.
Source record 11005703 at NHTSANHTSA communication ID: 11003395
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Connected Services - Frequently Asked Questions (FAQ)
Source components: UNKNOWN OR OTHER.
Source record 11003395 at NHTSANHTSA communication ID: 11003350
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
Source components: ENGINE.
Source record 11003350 at NHTSANHTSA communication ID: 11003353
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit oil seepage or oil leak onto the engine front cover, which becomes more apparent with dust adhesion.
Source components: ENGINE.
Source record 11003353 at NHTSANHTSA communication ID: 11003361
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the master warning light and/or the "In-Vehicle Network Malfunction" warning message in the instrument cluster on with DTC B119F:01 (TCU - Tel antenna No. 1 malfunction) stored.
Source components: ELECTRICAL SYSTEM.
Source record 11003361 at NHTSANHTSA communication ID: 11003351
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
Source components: ENGINE.
Source record 11003351 at NHTSANHTSA communication ID: 11003349
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
Source components: ENGINE.
Source record 11003349 at NHTSANHTSA communication ID: 11003695
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules.
Campaign / software reference: SSPC5
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · UNKNOWN OR OTHER.
Source record 11003695 at NHTSANHTSA communication ID: 11003694
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules.
Campaign / software reference: SSPC5
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · UNKNOWN OR OTHER.
Source record 11003694 at NHTSANHTSA communication ID: 11003358
NHTSA source summary · Original PDF not reviewed by Recallfolio
A new repair procedure has been developed to address DTC P0126:00 on SKYACTIV-G 2.0/2.5L engines (non-turbo). Mazda has introduced a replacement kit of the thermostat located within the Coolant Control Valve (CCV). NOTE: It is no longer necessary to replace the CCV for this DTC.
Source components: ENGINE.
Source record 11003358 at NHTSANHTSA communication ID: 11003398
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: UNKNOWN OR OTHER.
Source record 11003398 at NHTSANHTSA communication ID: 11003397
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
Source components: WHEELS.
Source record 11003397 at NHTSANHTSA communication ID: 11003396
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
Source components: SERVICE BRAKES.
Source record 11003396 at NHTSANHTSA communication ID: 11003399
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules.
Campaign / software reference: SSPC5
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · UNKNOWN OR OTHER.
Source record 11003399 at NHTSANHTSA communication ID: 11000775
NHTSA source summary · Original PDF not reviewed by Recallfolio
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
Source components: ENGINE.
Source record 11000775 at NHTSANHTSA communication ID: 11000772
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10 °C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
Source components: UNKNOWN OR OTHER.
Source record 11000772 at NHTSANHTSA communication ID: 11000355
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have the check engine light on with DTC P0524:00 or P055F:00 stored in memory. Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and improper oil pressure.
Source components: ENGINE.
Source record 11000355 at NHTSANHTSA communication ID: 11000785
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
Source components: ELECTRICAL SYSTEM.
Source record 11000785 at NHTSANHTSA communication ID: 11000674
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience that after the doors are locked and the Fuel Door Lock Delay with MAZDA CONNECT has passed (default setting is 90 seconds), the fuel-filler lid does not lock, but can be opened when pressed. NOTE: The fuel-filler lid does not lock immediately after the doors are locked, but after the time set in the Fuel Door Lock Delay (0, 30, 60, 90, and 120 seconds). Although the root cause has not been identified, the vehicle should be repaired by adjusting the fuel-filler lid opener cable position when there is a customer complaint.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
Source record 11000674 at NHTSANHTSA communication ID: 11000683
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about intermittent audio no sound from the MAZDA CONNECT infotainment system and/or static noise from the speakers. The concern may be reproduced by tapping on the dash pad near the MAZDA CONNECT center display and the following DTC's may be stored. U0186:08 Communication error with audio amplifier U2145:08 Communication error with remote tuner (RT) U2145:02 Communication error with remote tuner (RT)
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
Source record 11000683 at NHTSANHTSA communication ID: 10254098
NHTSA source summary · Original PDF not reviewed by Recallfolio
A customer may complain of a rattle noise from the right side of the dash. The noise may be coming from the passenger side airbag.
Source components: AIR BAGS.
Source record 10254098 at NHTSANHTSA communication ID: 10254188
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10 °C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 10254188 at NHTSANHTSA communication ID: 10254096
NHTSA source summary · Original PDF not reviewed by Recallfolio
The customer may report a rattling noise from the front of the vehicle under load. It may sound as if it is coming from the dashboard, but it is coming from the hood prop rod (aka lock-bonnet stay). The prop rod diameter was increased in November 2022 production, but in some circumstances, the noise may still be encountered in vehicles after this production range. Follow the repair information below to confirm the noise and how to eliminate it.
Source components: STRUCTURE:BODY:HOOD.
Source record 10254096 at NHTSANHTSA communication ID: 10254190
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
Source components: ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · LATCHES/LOCKS/LINKAGES.
Source record 10254190 at NHTSANHTSA communication ID: 10254183
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES.
Source record 10254183 at NHTSANHTSA communication ID: 10254191
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
Source components: WHEELS.
Source record 10254191 at NHTSANHTSA communication ID: 10254095
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about intermittent audio no sound from the MAZDA CONNECT infotainment system and/or static noise from the speakers. The concern may be reproduced by tapping on the dash pad near the MAZDA CONNECT center display and the following DTC's may be stored. U0186:08 Communication error with audio amplifier U2145:08 Communication error with remote tuner (RT) U2145:02 Communication error with remote tuner (RT)
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.
Source record 10254095 at NHTSANHTSA communication ID: 10254185
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · FORWARD COLLISION AVOIDANCE · SERVICE BRAKES, HYDRAULIC.
Source record 10254185 at NHTSANHTSA communication ID: 10252505
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. Specific Operation 3 Cause: The control logic is not appropriate. NOTE: If the concern occurs without the specific operation above, refer to TSB 09-019/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND/OR UNLOCK). To correct this issue, the control software of the LF control unit (LFU) has been modified.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
Source record 10252505 at NHTSANHTSA communication ID: 10252509
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF, Climate control
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
Source record 10252509 at NHTSANHTSA communication ID: 10252508
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10252508 at NHTSANHTSA communication ID: 10252507
NHTSA source summary · Original PDF not reviewed by Recallfolio
Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
Source components: POWER TRAIN.
Source record 10252507 at NHTSANHTSA communication ID: 10252502
NHTSA source summary · Original PDF not reviewed by Recallfolio
Symptom 1: Some customers may complain about hearing a grinding noise and/or vibration occur when applying the brake. This is due to rust on the rear brake disc plate. Symptom 2: Some vehicles may exhibit a squeal noise from the rear brakes when braking lightly while driving at a slow speed. The squeal noise is caused by the disk pad surface fluctuating.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10252502 at NHTSANHTSA communication ID: 10251391
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frequently Asked Questions (FAQ): General Questions, Reception Level Inspection, Setup and Getting Started, Dealer Processes, Registration / Enrollment, TCU Activation, WI-FI General Information, Conditions for Remote Engine Start Will Not Function, WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF, WI-FI Trial Period, Deactivation Mode, Interacting With The App, Educational Videos, Service Issues, Resources, Troubleshooting Page.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10251391 at NHTSANHTSA communication ID: 10251387
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · SERVICE BRAKES, HYDRAULIC · STEERING · TIRES · WHEELS.
Source record 10251387 at NHTSANHTSA communication ID: 10251390
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frequently Asked Questions (FAQ): General Questions, Reception Level Inspection, Setup and Getting Started, Dealer Processes, Registration / Enrollment, TCU Activation, WI-FI General Information, Conditions for Remote Engine Start Will Not Function, WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF, WI-FI Trial Period, Deactivation Mode, Interacting With The App, Educational Videos, Service Issues, Resources, Troubleshooting Page.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10251390 at NHTSANHTSA communication ID: 10251367
NHTSA source summary · Original PDF not reviewed by Recallfolio
NOTE: Before proceeding, perform MGSS Vehicle Inquiry (MGSS -> Other Applications -> Warranty Veh. Inq. -> RECALLS / SPECIAL SERVICE PROGRAMS -> Status) and check for Open campaigns. If any of the following campaigns are open, complete the campaign before proceeding with this service information. SSPC5 - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING 4219L - 2019MY MAZDA3 SUDDEN DECELERATION FROM FALSE BRAKE ACTIVATION 2024 CX-90 with VINS lower than JM2KK******151673 (produced before November 25, 2023), VCM software update available using TSB 15-001/24. DESCRIPTION This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle. IMPORTANT: Humans recognize an object with their eyes and decide whether or not to apply the brakes using their brain. The vehicle recognizes objects using the Forward Sensing Camera (FSC) and Front Radar sensor (FR), to determine brake application. Therefore, drivers may feel that the operation does not match the human feeling.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10251367 at NHTSANHTSA communication ID: 10251373
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10251373 at NHTSANHTSA communication ID: 10248393
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up The engine temperature gauge fluctuates The low coolant temperature indicator (blue) light stays on longer or comes on while driving Poor heater performance, especially at idle
Source components: ENGINE AND ENGINE COOLING.
Source record 10248393 at NHTSANHTSA communication ID: 10248388
NHTSA source summary · Original PDF not reviewed by Recallfolio
Qi Wireless Charger symptom troubleshooting
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:WIRELESS CHARGER/CRADLE.
Source record 10248388 at NHTSANHTSA communication ID: 10248387
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frequently Asked Questions (FAQ): General Questions Reception Level Inspection Setup and Getting Started Dealer Processes Registration / Enrollment TCU Activation WI-FI General Informatio Conditions for Remote Engine Start Will Not Function WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF WI-FI Trial Period Deactivation Mode Interacting With The App Educational Videos Service Issues Resources Troubleshooting Page
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
Source record 10248387 at NHTSANHTSA communication ID: 10248392
NHTSA source summary · Original PDF not reviewed by Recallfolio
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
Source components: ENGINE AND ENGINE COOLING.
Source record 10248392 at NHTSANHTSA communication ID: 10248389
NHTSA source summary · Original PDF not reviewed by Recallfolio
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.. CAUTION: DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another vehicle will disable Connected Services on both vehicles. If TCU activation is not performed, connected vehicle functions will not operate. This will have a negative impact on the customer because they will need to return to the dealer for repairs.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10248389 at NHTSA