Original record summaries, dates and identifiers for this model-year. Records 901–1,000 of 1,016, ordered newest first. Dated records on this page: Nov 20, 2019–Apr 21, 2020.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 21, 2020Service Bulletin/Repair Instructions
18-039-20
NHTSA communication ID: 10175733
NHTSA source summary · Original PDF not reviewed by Recallfolio
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Inlet Tube Fastener Torque This bulletin involves checking the torque on the water pump inlet tube fasteners to possibly eliminate coolant leak at this location. The customer may describe either a coolant leak or the coolant level is low.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRAME, Rear Seat Back, And Cushion Assembly For all 2-door vehicles, if rear seat exhibits one of the following conditions, please call FCA redacted Content prior to repair. Rear Seat Does Not Fold Cannot Remove Seat Seat Cables Stretched/Broken Seat Latch Seized Rear Seat release not working If no answer, please leave a message with dealer contact and VIN information. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DAMPER, Steering Additional service procedure steps before replacing the steering damper: Before istalling the steering damper to the vehicle, it is important to prime the new damper by 5 continuous compression ? extension stroke cycles by hand, each cycle consists of a full compression and a full extension stroke, without stops as fast as possible. Use large screwdrivers inserted in the bushings to aid in purging. This will allow you to stand on the lower screwdriver to hold the damper stationary and pump the rod end easier. Perform purge before installing NOTE: Hand purge to be completed in a vertical position with the base cup sticker end down toward the ground and the rod side facing up.See CSN V41 for detail procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.0L Oil Filter Cartridge Identification Differences And Oil Filter Element Servicing Procedure This bulletin outlines the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Inlet Tube Fastener Torque This bulletin involves checking the torque on the water pump inlet tube fasteners to possibly eliminate coolant leak at this location. The customer may describe either a coolant leak or the coolant level is low.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.0L Oil Filter Cartridge Identification Differences And Oil Filter Element Servicing Procedure This bulletin outlines the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Inlet Tube Fastener Torque This bulletin involves checking the torque on the water pump inlet tube fasteners to possibly eliminate coolant leak at this location. The customer may describe either a coolant leak or the coolant level is low.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.0L Oil Filter Cartridge Identification Differences And Oil Filter Element Servicing Procedure This bulletin outlines the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Inlet Tube Fastener Torque This bulletin involves checking the torque on the water pump inlet tube fasteners to possibly eliminate coolant leak at this location. The customer may describe either a coolant leak or the coolant level is low.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP, Water (Water Pump Inlet Tube) For concern of leak at water pump, please check and re-torque water pump inlet tube fasteners as described in Service Bulletin 07-001-20 before replacing the water pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP, Water (Water Pump Inlet Tube) For concern of leak at water pump, please check and re-torque water pump inlet tube fasteners as described in Service Bulletin 07-001-20 before replacing the water pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP, Water (Water Pump Inlet Tube) For concern of leak at water pump, please check and re-torque water pump inlet tube fasteners as described in Service Bulletin 07-001-20 before replacing the water pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaint includes check engine/MIL light on. Upon further inspection, fault codes will be found in the powertrain control module (PCM) for P0441, P0443 or P0449. Fault codes may be either active or stored.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaint includes check engine/MIL light on. Upon further inspection, fault codes will be found in the powertrain control module (PCM) for P0441, P0443 or P0449. Fault codes may be either active or stored.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaint includes check engine/MIL light on. Upon further inspection, fault codes will be found in the powertrain control module (PCM) for P0441, P0443 or P0449. Fault codes may be either active or stored.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a loud whistle noise upon engine start up.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BATTERY, Auxiliary (180 AMP) Mopar Engineering has reviewed the BBAUA180AA battery due to concerns over fitment in Chrysler, Jeep®, Dodge & Ram vehicles and has provided direction on usage. BBAUA180AA CAN BE USED in the following vehicles equipped with stop/start technology: ?MP ? Jeep Compass ?JL ? Jeep Wrangler ?JT ? Jeep Gladiator ?RU ? Chrysler Pacifica RU NOTE: Modify the BBAUA180AA battery positive mold cover by trimming 3mm of rubber on left side & bottom. ?WK ? Jeep Grand Cherokee ?WD ? Dodge Durango WK/WD NOTE:A vent kit is being created now and will replace the existing tube with a longer one and add an elbow to it for routing (availability is TBD).
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRAME, Front Seat Cushion For all 2 door JL vehicles, if the front driver or passenger seat is stuck in the folded (EZ entry) position or it won't return to normal seating position, review SB 23-020-19 prior to replacing the seat frame.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following Diagnostic Trouble Codes (DTCs) have been set:P0506 - Idle Speed Performance Lower Than Expected
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following Diagnostic Trouble Codes (DTCs) have been set:P0506 - Idle Speed Performance Lower Than Expected
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rubicon Front Seat Back Panel Loose This bulletin includes inspecting, reattaching and if needed replacing the front seat back panel(s). Customers may comment on the following:Front seat back panel is loose. Front seat back panel fell off. Gap between the seat back and seat assembly,Fig. 1. Gap Between Seat Back and Panel
NHTSA source summary · Original PDF not reviewed by Recallfolio
HANDLE AND CABLE, Seat Release If you have a 2 door vehicle built after 8/6/2019 with an EZ entry handle that is loose or appears broken, please call FCA Redacted Content prior to replacing any parts. If no response in 15 minutes, proceed with repair. EZ entry handle mounting bracket may have grease present which may have damaged the plastic of the EZ entry handle. Thoroughly clean mounting bracket of any contamination prior to installing a new EZ entry handle as outlined in Service Bulletin 23-002-20.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUTTON, Glass, Backlight ? EBL Hard top back flipper glass defroster grid is inoperative due to connector tab for electric backlight defrost grid broken off. For back flipper glass defroster terminal soldered joint failure, please send an email with the following to FCA Redacted Content: VIN Number Mileage A close up picture of both the back of the failed soldered terminal and the glass side of the failed solder joint. You can also speak to FCA Redacted Content if more information is needed. Please proceed with the repair using the repair kit as called out in the instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Body Control Module (BCM) Reconfigure for Enabling the Auto-On Comfort Settings This bulletin involves reconfiguring the BCM and possibly a radio reset, to enable the auto-on comfort settings. Customers may comment on one or more of the following:If below 4 °C (40 °F), the heated seats or heated steering wheel turn on by themselves. If above 26 °C (80 °F), the vented seats turn on by themselves. Cannot turn off the auto-on comfort feature. With the symptom/condition listed above, there?s no setting in the radio to turn the auto-on comfort feature off.
Source components: ELECTRICAL SYSTEM · SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Enhancements This bulletin involves updating the radio software level to 1848.24. Customers may experience one or more of the following: Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRAME, Front Seat Cushion For all 2 door JL vehicles, if the front driver or passenger seat is stuck in the folded (EZ entry) position or it won't return to normal seating position, please call Ajay Sharma (646) 236-2413 prior to any repairs or teardown. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REGULATOR, Front Door Window For concern of front window binding diagnosed as front window regulator, please send pictures of the issue to sandeep.tummuri1@fcagroup.com and contact Sandeep Tummuri at (248) 425-3419 If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WIRING KIT, Enclosure (Mopar JL hard top conversion accessory kit) The HVAC control panel requires replacement when GTP sales code is present to restore rear defrost function. The switch is not provided in this kit and a service replacement part must be ordered. See service information procedure for switch replacement and below chart for replacement part numbers. vehicle has GTP+BNH+HAA replace HVAC control with pn 6BE36TRMAC vehicle has GTP+BNH-HAA replace HVAC control with pn 6BE37TRMAC vehicle has GTP+HAA-BNH replace HVAC control with pn 6BE40TRMAC vehicle has GTP-HAA-BNH replace HVAC control with pn 6BE41TRMAC Please ensure that the proper color code is used in place of the part TRM designation. For any questions call John Altsman at (248) 512-9361.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LATCH, Folding Top For a concern of a loose latch in the closed position, it is not necessary to replace the latch unless broken. Refer to instructions in service library. The position of the receiver attached to the vehicle header can be adjusted to change the ammount of force required to latch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WIRING KIT, Enclosure (Mopar JL hard top conversion accessory kit) The HVAC control panel requires replacement when GTP sales code is present to restore rear defrost function. The switch is not provided in this kit and a service replacement part must be ordered. See service information procedure for switch replacement and below chart for replacement part numbers. vehicle has GTP+BNH+HAA replace HVAC control with pn 6BE36TRMAC vehicle has GTP+BNH-HAA replace HVAC control with pn 6BE37TRMAC vehicle has GTP+HAA-BNH replace HVAC control with pn 6BE40TRMAC vehicle has GTP-HAA-BNH replace HVAC control with pn 6BE41TRMAC Please ensure that the proper color code is used in place of the part TRM designation. For any questions call John Altsman at (248) 512-9361.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LATCH, Folding Top For a concern of a loose latch in the closed position, it is not necessary to replace the latch unless broken. Refer to instructions in service library. The position of the receiver attached to the vehicle header can be adjusted to change the ammount of force required to latch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Driver Assistance System Module (DASM) Enhancements This bulletin involves reprogramming the DASM with the latest software available. The customer may describe one or more of the following:Brakes may intermittently apply unexpectedly together with Instrument Panel Cluster (IPC) warnings. IPC warnings for the Forward Collision Warning (FCW) informing the driver to apply the brakes.
Source components: AIR BAGS · ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Driver Assistance System Module (DASM) Enhancements This bulletin involves reprogramming the DASM with the latest software available. The customer may describe one or more of the following:Brakes may intermittently apply unexpectedly together with Instrument Panel Cluster (IPC) warnings. IPC warnings for the Forward Collision Warning (FCW) informing the driver to apply the brakes.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Driver Assistance System Module (DASM) Enhancements This bulletin involves reprogramming the DASM with the latest software available. The customer may describe one or more of the following:Brakes may intermittently apply unexpectedly together with Instrument Panel Cluster (IPC) warnings. IPC warnings for the Forward Collision Warning (FCW) informing the driver to apply the brakes.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Driver Assistance System Module (DASM) Enhancements This bulletin involves reprogramming the DASM with the latest software available. The customer may describe one or more of the following:Brakes may intermittently apply unexpectedly together with Instrument Panel Cluster (IPC) warnings. IPC warnings for the Forward Collision Warning (FCW) informing the driver to apply the brakes.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shimmy In The Steering Wheel After Hitting An Irregularity On The Road Surface This bulletin involves discussing an available video instructing the technicians on how to properly diagnosis and repair this issue.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAMERA, Rear View For concerns of back up camera flicker/blank/blue/black screen or camera inop, please ensure Radio is at latest software level. After update, system requires three sleep cycles to function properly. Please verify camera LVDS cable connection at camera and radio head unit. Also verify harness connection between high mounted stop lamp and body harness for bent pins or loose connection at XY310A, XY485A. Please create and send a copy of the vehicle scan report and specify radio SW version and radio head unit ID to Bing Guo and Rafay Adil via email bingruo.guo@fcagroup.com (248) 500-7355 rafay.adil@fcagroup.com (248) 736-7059 Please call for any additional questions or assistance needed. If no response in 15 minutes, proceed with repair. Please be sure to attach a copy of the Vehicle Scan Report on the repair order.
Source components: BACK OVER PREVENTION · PARKING BRAKE · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shimmy In The Steering Wheel After Hitting An Irregularity On The Road Surface This bulletin involves discussing an available video instructing the technicians on how to properly diagnosis and repair this issue.