2014 GMC SIERRA 1500 Manufacturer communications & TSBs.Page 17
Original record summaries, dates and identifiers for this model-year. Records 1,601–1,700 of 3,022, ordered newest first. Dated records on this page: Jun 29, 2015–Oct 29, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 29, 2015Service Bulletin/Repair Instructions
PIP5345
NHTSA communication ID: 10114934
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about being to achieve pre-load when setting up the pinion bearing pre-loads during reassembly of the 9.5/9.76 inch rear axles. Technician will need to use pinion gear install washer part number 11609638 onto the pinion shaft between the flange and nut. Tighten the pinion nut until you achieve 10 pound inch or 1.0 newton rotating torque. After the torque has been achieved back the nut off and remove the washer. Tighten the nut back down until you achieve 15 pound inch or 1.7 newton meters for used bearings or 20 pound inch 2.25 newton meters for new bearings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when shutting the vehicle off when the radio is turned off prior, the radio will turn back on in the muted condition on the next key cycle. No action should be taken at this time as this is considered a normal operating characteristic.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that engine runs and idles rough. Technician will find P0171 and or P0174. Technician will need to inspect the positive crankcase ventilation tube for a vacuum leak on the left side of the engine. Replace positive crankcase ventilation air tube and cover it with conduit to protect from repeat damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to repair information to correct a customer concern of the hood fluttering, vibrating or displaying visible motion at highway speeds or over rough road surfaces.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2015 Chevrolet Colorado and GMC Canyon to diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: STRUCTURE:BODY:TAILGATE:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for vehicles that exhibit a driver?s power memory seat and power adjustable pedals inoperative. Look for poor terminal tension at the left instrument panel fuse block connector X1 terminals 27 and 28. If poor retention is found in these terminals replace them with terminated lead part number 19301761.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:MECHANICAL · SEATS:FRONT ASSEMBLY:POWER ADJUST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
Source components: STRUCTURE:FRAME AND MEMBERS · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.25mm the crankshaft balancer will need to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
Source components: ENGINE · POWER TRAIN · SERVICE BRAKES, HYDRAULIC:POWER ASSIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of hearing a squeak noise from the driver or passenger front door armrest area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin contains recommendations of what needs to be done to swap/install camper outside rearview mirrors on a vehicle not originally equipped with them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. If the fuel found in the vehicle has an American Petroleum Institute specific gravity reading of 39 - 44, and the fuel sample you used for comparison has an American Petroleum Institute specific gravity reading of 30 - 39, drain the fuel system and refill with a known good diesel fuel and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of a Service Stabilitrak message displayed on the Driver Information Center (DIC). During diagnosis, a technician may find DTC C0196-5A set in the Electronic Brake Control Module (EBCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. non overpower engine non-function of pistons, cylinders, valve train components, and DTC P003A or P111D set.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides service personnel with a guide to determine which SI documents and scan tool parameters to reference when encountering an: Exhaust Fluid Quality Poor message displayed, and a Reductant Fluid Quality Test status that will Pass, Time Out, Fail or Interrupt and other DEF messages that maybe observed.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides dealership personnel with policies and procedures regarding damaged, disassembled or improperly packaged turbochargers returned to Warranty Part Center.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a vibration at highway speed. Technician will need to replace the wheel for a rolled lip of aluminum in the hub opening.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to access XM Weather. If the system responds by highlighting the XM Weather Icon but it does not enter the application technician should replace the Human Machine Interface module for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show ?No Audio? in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center when operated below 10 degrees Fahrenheit (-12 Celsius). Technician may find C0398 or C0326 stored in the Transfer Case Control Module. For vehicles with Regular Production Option Code NPO, NQH and NQ6 and only setting Diagnostic Trouble Codes C0398 or C0398 and C0326 reprogram the transfer case control module with the latest calibration from TIS2WEB and perform the setup procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15304 - Service Update. This bulletin provides a service procedure to reprogram the transfer case control module on the vehicles listed above. In low ambient temperatures, below 5°F (-15°C) a transfer case brake motor assembly malfunction may occur. Diagnostic Trouble Code (C0398 - Range Position Correlation Fault) will be set, locking the transfer case in ?4HI? until the vehicle is serviced. This software update also addresses other transfer case control issues for overall improved drivability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with excessive paint chipping on the front lower bed corners. Technician will need to repair the damage first. After the damage has been repaired install the protector.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with misfires or roughness on cold start up. Technician may find a Diagnostic Trouble Code P0300 stored. Technician will add coolant dye to the system, run engine through warm up, pressurize the cooling system on a cold soak engine and inspect the suspect cylinder with a bore scope for coolant dye evidence. If coolant is found in the cylinder do not replace the cylinder head because that will not repair this concern. Dealer will need to contact General Motors Product Quality Center for engine replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 6.6L Duramax Diesel Engine Part number 12638502 has been placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact the General Motors Product Quality Center for further assistance.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin outlines the recommendations and procedures for diagnosing and repairing vibrations caused by wheel and tire, axle components and/or propeller shafts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician before replacing the crankshaft to review the following. Dealer should complete the Service Information diagnostics and the Cost Comparison Worksheet for Assembly Repair vs. Replacement. Technician will use the latest version of 09-06-04-026G to verify the Engine Control Module calibration is not an aftermarket calibration. If the customer prefers to keep the original numbers matching engine please call General Motors Technical Assistance Center for repair direction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Codes P0089, P127C, P127D, P0192, P0193, P228C, P228D, and P006C. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Codes that are stored. If Service Information does not lead to a repair for the concern, the fuel rail pressure sensor should be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure after an oil change. Technician will inspect the oil filter part number PF63E. Part number PF48 oil filter will fit but will cause a low oil pressure concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: FOR SOME VEHICLES, ONCE SPEED HAS REACHED 56-73 KM/H (35-45 MPH) OR 96-120 KM/H (60-70 MPH), EITHER IN STEERING WHEEL OR THE SEAT, VIBRATIONS CAN BE FELT. MODEL 2014 SILVERADO 1500, SIERRA 1500, 2015 SILVERADO 1500, SIERRA 1500. *PE
Source components: SEATS · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: IN SOME VEHICLES AND TRUCKS, WHEN TRANSFERRING INTAKE MANIFOLD TO REPLACE AN ENGINE LONG SERVICE BLOCK, DUE TO INTERNAL DAMAGE, EXTREME CAUTION MUST BE TAKEN FOR COMPONENT DEBRIS VIA BROKEN, BENT OR MISSING INTAKE VALVES. *PE
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: ON SOME TRUCKS, MESSAGE APPEARS IN DIC REGARDING SYMPTOM OF AN INTERMITTENT SERVICE TRAILER BRAKE AND DIAGNOSTIC TROUBLE CODES (DTC) ARE SET IN CHASSIS CONTROL MODULE. MODEL 2014 SILVERADO 1500, SIERRA 1500, 2015 SIERRA, SILVERADO. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a grind, pop, shudder or bind feeling/noise in the steering column when turning left or right. Technician will inspect for the lower column bearing to be out of position and the upper intermediate steering shaft to lower column shaft bolt and nut may be contacting the inhibitor/shiftier cable bracket. Technician will remove the steering column from the vehicle and replace the lower bearing adapter assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a service trailer brake message on in the vehicle. The technician will find diagnostic trouble codes C1115, C1116, C1117, or C1118. In most cases the chassis control module is not the cause of the trouble codes. The technician should inspect the wiring between the chassis control module and the trailer brake control switch. The inline connectors X185 or X138 as well as the connectors X1 and X5 of the X61A junction block should be thoroughly inspected looking for backed out, loose, poor retention or any other terminal issues. If there are no wiring concerns are found the trailer brake control switch is most likely the cause.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of addition information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
Source components: ELECTRICAL SYSTEM · SEATS:FRONT ASSEMBLY:POWER ADJUST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information on identifying non-GM ECM Calibration use and Power-Up hardware detection in Duramax® Diesel Engines using GDS 2.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the part restriction for the instrument panel cluster has ended. The instrument panel cluster can now be ordered through the part department without any authorization.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication for the dealer to please communicate to the customer this condition is a normal operating characteristic of their vehicle. Customer's timeshift audio playback is choppy, distorted, skipping, or garbled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon Malfunction Indicator Lamp on. Technician should follow published Service Information diagnostics that will lead to an oil pump replacement. Technician should replace the oil pump. If debris is found, the main and rod bearings should be inspected before engine replacement is considered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of additional information while diagnosing a diagnostic trouble code P0420. Check for a possible leak in the exhaust system behind the bank one number 2 oxygen sensor. If a leak is found or there is an aftermarket utility bed or trailer hitch installed. Check for a minimum clearance of 1.5 to 2 inches of the exhaust system. Install a new clamp and torque it to 40.5 foot pounds.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within?2.0?mm (0.079?in) of the mounting plates. The rotors and pads should be replaced with the updated part number If the pads are out of specification, perform normal Service Information diagnostics to determine the cause of the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of engine misfire/tick noise, Malfunction Indicator Lamp (MIL) On, DTC P0300 set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that replacement transfer case halves will not be threaded. No additional thread tapping will be necessary to assemble the transfer case as the attaching metric bolts are self-tapping. Drive the bolts into the new case and torque them to specification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional information while diagnosing a diagnostic trouble code P0420. Check for a possible leak in the exhaust system behind the bank one number 2 oxygen sensor. If a leak is found or there is an aftermarket utility bed or trailer hitch installed. Check for a minimum clearance of 1.5 to 2 inches of the exhaust system. Install a new clamp and torque it to 40.5 foot pounds.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
Source components: EQUIPMENT:ELECTRICAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.