Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 2,400, ordered newest first. Dated records on this page: Oct 5, 2015–Mar 14, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 14, 2016Service Bulletin/Repair Instructions
16-NA-075
NHTSA communication ID: 10112789
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to apply thread locker to the catalytic converter bolts for vehicles with the condition of a knock, rattle, or ping noise from under the vehicle into the passenger compartment
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on how to take the vehicles out of transport mode for vehicles with the condition of Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN REAR WHEEL DRIVE MANUAL TRANSMISSIONS HAVE BEEN PLACED ON RESTRICTION. DEALER WILL NEED TO CONTACT GENERAL MOTORS PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to Water Test, Apply Sealer at Laser Braze to the vehicle that has the conditon of a Wind Noise and/or Water Leak at Front Roof or Windshield, Water Running Down Interior A-Pillar
Source components: STRUCTURE · STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN REAR WHEEL DRIVE MANUAL TRANSMISSIONS HAVE BEEN PLACED ON RESTRICTION. DEALER WILL NEED TO CONTACT GENERAL MOTORS PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS NEED TO DIAGNOSE AND REPAIR VEHICLE THAT MAY HAVE A CONCERN WITH NAVIGATION ICON NOT SHOWING THE CORRECT LOCATION THEN JUMPING TO THE CORRECT LOCATION. THE POSITION INDICATOR MAY SHOW THE VEHICLE TURNING IN THE OPPOSITE DIRECTION OR MAY SHOW THE VEHICLE TRAVELING OFF THE ROAD. TECHNICIAN WILL INSPECT THE HUMAN MACHINE INTERFACE MOUNTING. FOLLOW SERVICE INFORMATION FOR THE CORRECT ORIENTATION OF THE HUMAN MACHINE INTERFACE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On or Set DTC B101D When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
Source components: AIR BAGS · AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the active safety control module for vehicles with the condition of collision/detection system inoperative
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles that have the condition of rust showing at hem flange
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair vehicles that may have engine misfire and check engine light with any or all cylinder misfires only on deceleration. Technician will need to remove the accessory belts and drive or brake stall at signature RPM. If the concern is gone inspect for debris in the belt or pulleys causing a jump and false misfires. Also lift the engine to unload the engine mounts and test again. If concern is gone then inspect for a ground out concern with the mounts causing false misfires.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE OIL MIXED IN WITH THE ENGINE COOLANT. TECHNICIAN WILL NEED TO INSPECT THE OIL COOLER IF EQUIPPED FOR POSSIBLE LEAKING INTO THE COOLING SYSTEM THROUGH THE RADIATOR. IF NO ISSUE FOUND REPLACE THE ENGINE AS WELL AS ALL RUBBER COOLANT HOSES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ends
NHTSA source summary · Original PDF not reviewed by Recallfolio
A customer may comment they receive an "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the DIC when attempting to activate the cruise. Other possible messages may include, Park Assist Symbols Unavailable, Lane Departure Warning Unavailable and Rear Auto Braking Unavailable. If normal diagnostics lead to a concern that can be duplicated and there are no DTCs present, the concern is most commonly caused by one of the following issues. Perform the yaw rate sensor learn procedure (Multi Axis Sensor), clear any DTCs that may have set during programming, and let vehicle go to sleep before evaluating the concern.
Source components: ELECTRICAL SYSTEM · VEHICLE SPEED CONTROL:CRUISE CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the radio antenna and reprogram the HVAC control module to correct a condition of auto-on rear window defogger and outside rear view mirror defogger inop
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to install a ionizer, clean evaporator and inspect the drain tube on vehicles that exhibit a condition of a musty odor from the HVAC vents on start up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician will need to perform a Multi Axis Sensor yaw rate sensor learn procedure. Also perform the Long Range Radar Learn called-out in the Radar Sensor Module - Long Range Programming and Setup procedure in Service Information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" MESSAGE ON THE DRIVER INFORMATION CENTER WHEN ATTEMPTING TO ACTIVATE THE CRUISE. TECHNICIAN WILL NEED TO PERFORM A MULTI AXIS SENSOR YAW RATE SENSOR LEARN PROCEDURE. ALSO PERFORM THE LONG RANGE RADAR LEARN CALLED-OUT IN THE RADAR SENSOR MODULE - LONG RANGE PROGRAMMING AND SETUP PROCEDURE IN SERVICE INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician how to diagnose vehicles with the CD player inoperative. If this concern is encountered, cycle the CD player fuse and re-evaluate the concern. If the concern is no longer present, replace the CD player. When the CD player is still found to be inoperative after cycling the fuse follow Service Information diagnostics.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ome customers may comment on a malfunction indicator lamp (MIL) illuminated. They may also comment that they intermittently are unable to shift into Reverse. When checking the vehicle for DTCs, the engine control module (ECM) may report P0502 as current or in history. This may be caused by water intrusion into the vehicles manual transmission output speed sensor or could be induced by the customer slipping the clutch for an extended period of time, as in holding the vehicle on a hill.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician when the customer comments that their digital vehicle speed display is showing a different speed than the analog vehicle speed display. There may be up to 2 miles per hour difference between the digital and analog vehicle speed displays. This is a normal condition due to the calculation tolerances being different for the two driver viewing angles for the analog speedometer; it may also appear to increase the difference between both displays. No part replacement is required as this is a normal operating characteristic of the vehicle. For CTS vehicles built between April and June of 2011 or the 2013 ATS, SRX, XTS built before August 29 2012 may have a 3 miles per hour or more variation. The technician is to replace the instrument panel cluster for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · FUEL SYSTEM, GASOLINE · FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a Diagnostic Trouble Code B2625 Symptom Code 02. Technician should not replace the Body Control Module for this concern. Technician should disconnect the battery negative terminal for 30 seconds. Technician can now reconnect the battery. The Diagnostic Trouble Code will be stored as history and you will now be able to use the clear Diagnostic Trouble Code command to erase the Diagnostic Trouble Code.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the lower center section of the display will not work when pressed. Technician will need to replace the Integrated Center Stack for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may comment on a malfunction indicator lamp (MIL) illuminated. They may also comment that they intermittently are unable to shift into Reverse. When checking the vehicle for DTCs, the engine control module (ECM) may report P0502 as current or in history. This may be caused by water intrusion into the vehicles manual transmission output speed sensor or could be induced by the customer slipping the clutch for an extended period of time, as in holding the vehicle on a hill.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Malfunction Indicator Lamp (MIL) Illuminated, Intermittently Unable to Shift into Reverse, DTC P0502 Set Condition/Concern Some customers may comment on a malfunction indicator lamp (MIL) illuminated. They may also comment that they intermittently are unable to shift into Reverse. When checking the vehicle for DTCs, the engine control module (ECM) may report P0502 as current or in history. This may be caused by water intrusion into the vehicles manual transmission output speed sensor or could be induced by the customer slipping the clutch for an extended period of time, as in holding the vehicle on a hill.
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM) · POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that intermittently the Outside Air Temperature displays dashes instead of a numeric value. This is normal operation of the CUE system, whenever the battery is disconnected and reconnected for service repairs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If a vehicle comes into the dealership with a knock noise, seized engine, lower end squeak or squeal or any condition that you suspect a rod or main bearing failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15404 - CUSTOMER SATISFACTION PROGRAM. CERTAIN VEHICLES MAY HAVE A CONDITION THAT IF INVOLVED IN A NON-DEPLOYMENT CRASH MAY NOT AUTOMATICALLY ACTIVATE ANY POST-CRASH ACTIONS, INCLUDING AN AUTOMATIC CRASH RESPONSE (ACR) CALL FROM ONSTAR, DOOR UNLOCK, INTERIOR LAMP ILLUMINATION, HAZARD LAMP ACTIVATION, HVAC BLOWER SHUTDOWN, AND FUEL PUMP SHUTDOWN. A NON-DEPLOYMENT CRASH EVENT IS NOT SEVERE ENOUGH TO DEPLOY THE SEAT BELT PRETENSIONERS OR AIRBAGS. ALL POST-CRASH ACTIONS INCLUDING AN ONSTAR ACR CALL WILL FUNCTION AS DESIGNED FOR ANY CRASH WITH A SEAT BELT PRETENSIONER OR AIRBAG DEPLOYMENT. THE ONSTAR BUTTONS CAN BE PRESSED TO REQUEST HELP, IF NEEDED. DEALERS ARE TO REPROGRAM THE SDM, OR IN SOME INSTANCES, REPLACE THE SDM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct customer concerns about blank screen after startup and reverse, rear view camera message on, touch screen inoperable, Bluetooth and navigation concerns.
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may comment that the vehicle has reduced acceleration at low speed and/or transmission is slipping from a launch. Technicians may find DTC P0751 set or stored in history. This condition may be caused by the Clutch Select Solenoid Valve 2 (359), located in the lower valve body, sticking in its bore resulting in a 4th gear start. Note: This condition can be very intermittent and difficult to duplicate.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when shutting the vehicle off when the radio is turned off prior, the radio will turn back on in the muted condition on the next key cycle. No action should be taken at this time as this is considered a normal operating characteristic.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2015 Chevrolet Colorado and GMC Canyon to diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin is requesting information from dealers on a customer concern of loss of audio, chimes or turn signal click/clack with DTC U0180 or B1325 sym03 set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
Source components: STRUCTURE:FRAME AND MEMBERS · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).