2013 Audi Q5 Manufacturer communications & TSBs.Page 8
Original record summaries, dates and identifiers for this model-year. Records 701–800 of 1,615, ordered newest first. Dated records on this page: Sep 25, 2014–Mar 10, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 10, 2015Service Bulletin/Repair Instructions
A171558 2038119-
NHTSA communication ID: 10120673
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 17 number 14-52 dated September 2, 2014. The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
NHTSA source summary · Original PDF not reviewed by Recallfolio
The customer complains that the Audi Connect Online service only reaches 2G service within the Indianapolis metropolitan area. This bulletin applies only to model year 2011-2013 A8, 2012-2013 Q7, and 2013 A4, A5, A5 cabriolet, and Q7 vehicles. For 2012-2013 A6 and A7 vehicles, see TSB 2039515. A telephone module that supports 3G service on the 1900MHZ band was installed beginning with model year 2014 vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 70 number 14-39 dated August 11, 2014. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit.
Source components: SERVICE BRAKES · SERVICE BRAKES, AIR:DISC:PADS · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 15-03 dated February 9, 2015. Customer may report hearing brake noise when the vehicle comes to a stop from front brakes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various squeaks and rattles are heard in the front or rear doors when the vehicle is driven over rough roads. Friction in the points of contact between the door trim panels can cause these noises.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Paint flakes off radiator grille or license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This document contains the Technical Service Bulletin that supersedes Technical Service Bulletin Group 00 number 13-50 dated May 22, 2013. A repair authorization must be obtained if a Q5 hybrid arrives at an Audi dealership and requires diagnosis or repair for the traction motor, power electronics, high voltage battery, high voltage cables, high voltage A/C compressor. Auxiliary battery, and any hybrid warning messages in the instrument cluster. A Technical Assistance Center ticket must be created before starting repairs. These procedures are mandatory until further notice.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?Hybrid drive: system error. Please go to workshop? is shown in the instrument cluster. Electric and hybrid operation are no longer possible. DTC P0AD600 is stored in the hybrid battery management module. The hybrid battery management control module unlearns the end stops of the air supply valve in the cooling module because of a software problem.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Harsh downshifts when braking or harsh 1-2 upshift under acceleration. Further transmission control module software calibration to improve shift concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 20 number 14-41 dated October 9, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
NHTSA source summary · Original PDF not reviewed by Recallfolio
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
NHTSA source summary · Original PDF not reviewed by Recallfolio
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 94 number 14-34 dated March 7, 2014. The high beam is inoperative on one side of the vehicle. The low beams operate correctly. A warning may appear in the instrument cluster. DTCs may be present in the central electrics control module. The connection for the high beam shutter is not connected in the affected headlight.
NHTSA source summary · Original PDF not reviewed by Recallfolio
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 21 number 14-20 dated November 17, 2014. MIL on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-29 dated September 16, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (address word 01), is storing one or more engine misfire fault codes. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various squeaks and rattles are heard in the front or rear doors when the vehicle is driven over rough roads. Friction in the points of contact between the door trim panels can cause these noises.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 85 number 14-20 dated February 24, 2014. DTCs may be stored in the heating and air conditioning electronics control module. A faulty printed circuit board in the fresh air blower control module and/or the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower can cause Improper operation of the fresh air blower.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 66 number 14-42 dated October 9, 2014. The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Update has been proactively released to prevent the following condition from occurring in the vehicle. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Update has been proactively released to prevent the following condition from occurring in the vehicle. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may report poor A/C performance or that A/C is inoperative. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC codes for the vehicles listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 40 number 14-42 dated July 8, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. This bulletin applies only to vehicles equipped with 75mm hydro-bushings. This bulletin does not apply to vehicles equipped with 65mm bushings. High ambient temperatures at the hydraulic guide links cause the noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 20 number 14-34 dated June 26, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 37 number 12-65 dated September 25, 2012. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced. No faults are stored. TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. The DTCs are stored due to an issue with the transmission control module software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 37 number 14-42 dated August 1, 2014. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module (TCM).
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer reports that the side assist is providing warnings when no vehicles are present. The radar is reflected from the rear wheels back to the sensors, resulting in a false side assist warning.