Original record summaries, dates and identifiers for this model-year. Records 1–100 of 823, ordered newest first. Dated records on this page: Sep 24, 2021–Jun 19, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 19, 2026Service Bulletin/Repair Instructions
SA-041-26
NHTSA communication ID: 11034447
NHTSA source summary · Original PDF not reviewed by Recallfolio
This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 01-008/23 06/05/23 Some vehicles may exhibit rattling noises from the engine compartment and oil leakage from the drive belt auto tensioner. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed. REPAIR PROCEDURE If the tensioner is found to be "No Good" after completing the Drive Belt Auto Tensioner Inspection, replace it with a modified part according to the instructions on MGSS online:
NHTSA source summary · Original PDF not reviewed by Recallfolio
DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
Source components: ENGINE · POWER TRAIN · SERVICE BRAKES · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-003/22 03/02/22 DESCRIPTION Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not to continue filling after nozzle shut off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit codes. • Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. • For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Noise, Vibration, and Harshness (NVH) Diagnostic Guidelines Diagnostic Guidelines When diagnosing NVH concerns, it is essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.
Source components: POWER TRAIN · STEERING · SUSPENSION · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the SiriusXM satellite radio unit, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a noisy HVAC blower motor or odor after a cabin air filter replacement. Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit following symptoms: 1. The rearview mirror (1) rattles up and down (2) while adjusting the mirror. 2. The rearview mirror (1) makes a rattle noise depending on the road surface conditions while driving. This concern is caused during rearview mirror installation. The adhesive is squeezed out between the windshield and the mirror base. The rearview mirror is assembled on top of the overextended adhesive. The adhesive is softened by heat, and loosening screws, results in a rattling concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The SKYACTIV-DRIVE FW6A-EL AT uses “Automatic Transmission Fluid (ATF) Type: FZ”. Only use “ATF-FZ” to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plate’s surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · SERVICE BRAKES, HYDRAULIC · STEERING · TIRES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plateâÂÂs surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plateâs surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · SERVICE BRAKES, HYDRAULIC · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plate's surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple CarplayâÃÂâ/ Android AutoâÃÂâ will not connect) 6. Over-sized wheels/tires (incorrect GPS location)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.
Source components: ELECTRICAL SYSTEM · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a squeaking noise may be heard from the exhaust manifold when the idle speed drops from fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. When returning from fast idle to normal, the stuck valve suddenly opens due to thermal change around it which causes abnormal noise. To eliminate this concern, the internal design of the exhaust manifold has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not to continue filling after nozzle shut off. Refer customer to Owner's Manual Warning:
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
Source components: POWER TRAIN · SUSPENSION:FRONT:WHEEL BEARING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · SERVICE BRAKES, HYDRAULIC · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.
Source components: POWER TRAIN · POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the rear door seaming welt (1) comes off when stepping in and/or out of the vehicle. This is caused by the gripping force of the seaming welt being insufficient for frequent usage of the rear seat (vehicle used for ride sharing). No mass production change is planned.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIVî Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIVî vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.