Original record summaries, dates and identifiers for this model-year. Records 101–200 of 833, ordered newest first. Dated records on this page: Sep 8, 2023–Mar 17, 2025.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 17, 2025Service Bulletin/Repair Instructions
9100471
NHTSA communication ID: 11015810
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Rear Defroster Inoperative Customers may experience one or more of the following: ● Rear window is not defrosting. ● The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window"
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Turbocharger Kit Please note many parts of the Turbo Assembly can be serviced separately and complete turbo replacement may not be necessary. If the Turbo is being replaced for a noise or a rattle, inspect the wastegate for binding. The actuator kit is serviced separately. If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed oring for a leak. The o-ring is serviced separately
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Air Trapped in Steering Damper Warranty Extension XF1 A shimmy in the steering wheel after hitting an irregularity on the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Air Trapped in Steering Damper Warranty Extension XF1 A shimmy in the steering wheel after hitting an irregularity on the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
NHTSA source summary · Original PDF not reviewed by Recallfolio
SWITCH Power Window Before replacing the window switch, please follow these steps: 1.- Review the master window Switch for any physical issue (Button stuck, broke). If not, physical issue is found move to next step 2.- Make sure all the switches harness are properly connected, disconnect the switch and reconnect it, and reverify the issue. If after performing these steps the switch remains faulty, please replace the switch
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Air Trapped in Steering Damper Warranty Extension XF1 A shimmy in the steering wheel after hitting an irregularity on the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Axle Assembly Do not replace the Axle for Axle Locker Sensor failure. The parts kit (SENSOR KIT, Axle: 68544629A$) must be used to repair the Axle Locker Sensor on JL/JT equipped with the M210 and M220 Tru-Lok axles (DSE). Internal axle components are serviceable. Complete axle assemblies should not be replaced unless necessary due to damaged housing. Over repairs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"PUMP WATER For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front and Rear Axle Sensor Kit **Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? C1451-11 - Service Axle Locker System** Customers may also comment on a Service Axle Locker message displayed in the Electronic Vehicle Information Center (EVIC) for this condition.
Source components: BACK OVER PREVENTION · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Floor Console USB Inoperative Customers may comment on the following: ? Customer states the Apple Carplay/Android Auto? does not work or is intermittently working when their device is plugged into the center console bin USB port. This replacing the center console USB cable.
Source components: ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS:ACCESORY POWER OUTLET/JACK/PORT/USB/SAE/CIGARETTE LIGHTER · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
ERG Hydraulic Tensioner Before replacing any FEAD components, please check FEAD belt layout as per the engine sales code. Customer complaint may include a noise from under the hood described as a squeal, screech, squeak, chirp or belt-related noise and/or noisy tensioner/pulley. Please refer to SOL# S2309000007.
Source components: BACK OVER PREVENTION · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.