2024 Jeep GRAND CHEROKEE Manufacturer communications & TSBs.Page 4
Original record summaries, dates and identifiers for this model-year. Records 301–400 of 545, ordered newest first. Dated records on this page: Dec 9, 2024–Apr 16, 2025.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 16, 2025Service Bulletin/Repair Instructions
9100549
NHTSA communication ID: 11017080
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Keyfob WL/WS/LB Key fobs unable to be programmed at dealers. Please check current stock and verify a green check mark on part label. If not present send part back to Mopar under RMA 8925-792 and replace with clean stock from Mopar. Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Display Verify Z part number availability. Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Key Fob Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Trailer Tow Module(TTM) Updates Customers may comment on one or more of the following: ● If the vehicle is traveling at less than 5 kph (3 mph) and the brake pedal is pressed, then both turn lights will flash for two milliseconds. ● If the vehicle is traveling at less than 5 kph (3 mph) and one turn light is activated, then the opposite turn light will flash for 20 milliseconds This bulletin involves updating the TTM with the latest available software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Radio Frequency Hub Module (RFHM) Updates. Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● B1A10-00 - RKE FOB 1 Battery Low. ● B1A11-00 - RKE FOB 2 Battery Low. ● B23D7-14 - Gated Park Control - Circuit Short To Ground Or Open. Customers may also experience one or more of the following: ● **Uconnect app requests not functioning (none of the app functions work, lock/unlock, remote start).** ● Vehicle won’t start unless the fob is pressed to Keyless Ignition Node (KIN). ● Key fob not detected when inside vehicle. ● Passive Entry (PE) intermittently inoperative. ● KIN unresponsive. ● Welcome feature does not activate at times. This bulletin involves inspecting and possibly updating the RFHM module with the latest available software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: ● P0629 - Fuel Pump Control Circuit High. ● P0171 - Fuel system Lean. ● P0087 - Fuel Rail Pressure Too Low - Bank 1. Customers may also experience one or more of the following: ● Variable speed fuel pump doesn't start after refueling. ● The Instrument Panel Cluster (IPC) unable to calculate the instantaneous fuel economy under heavy acceleration. ● The oxygen sensor can give incorrect values when entering Electric Vehicle (EV) mode. False fault detection is possible when this event occurs. ● The rear half shafts are damaged due to accelerating in drive with the Electronic Parking Brake (EPB) applied. This bulletin involves updating the PCM with the latest available software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"MODULE Steering Control Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Ebooster When replacing the brake ebooster under warranty. Please return all associated parts which includes the snap rings so that the parts can be review by engineering."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."
NHTSA source summary · Original PDF not reviewed by Recallfolio
LOWER ACTIVE GRILL SHUTTER If the upper or lower AGS seems to be inop please make sure you CLEAR the DTCs BEFORE swapping the old AGS for a new one, and test if the error code returns. Very often the wiring harness presents corrosion, so make sure to check it for any damage BEFORE swapping the AGS. Corrosion in the harness disrupts communication with the AGS, which sets up the DTCs for AGS performance and lights the CEL. If the AGS is inop and it will be replaced and sent back to Stellantis also send back the wiring harness with it. Make sure to fully perform the PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE as indicated in the service library.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P2066 - Fuel Level Sensor 2 Performance. Customers may experience the following: ● When overriding the electric park brake (EPB) while it remains engaged due to unbuckled seat belt in Drive or Reverse, the high torque request with the parking brake engaged may lead to Rear Drive Unit (RDU) damage/broken."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Droning Humming Growling Noise Customers may comment on the following: ● Droning, humming or growling noises while in drive, park or neutral. This condition might disappear if the door is opened or a window is lowered down or when covering the Active Noise Cancellation (ANC) microphones This bulletin involves performing a PROXI Configuration Alignment."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Oil Leaking From Oil Filter Area Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: ● Oil found on the ground beneath the vehicle. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. "
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Frt Stabilizer assembly(smartbar) BSR from the front end due to Smartbar (disconnecting front sway bar). Root cause was identified as anti-rotation bracket (connects the actuator to the stabar) coming loose due to inadequate clamp load at the joint and weld (holds the bolt shaft and bracket flange) was poorly designed. If any vehicle causes BSR because of this Bracket failure (loose joint/ bracket bends) DO NOT replace whole stabar assembly, instead replace with the service kit (PN#68730602AA). Dealer must need to order the parts from part ordering system for this claim. This kit contains 1 bracket (PN 68730603AA), 3 M10 Nut (PN 68730605AA), 2 M8X1.5 Bolt (PN 68730606AA) and 2 M10X1.5 bolt (PN 06513427AA). 1 M10 Bolt (PN 68730607AA). This kit will also contain a new torque instruction for the bolt which holds the clamp bracket to this failed anti-rotation bracket. DO NOT apply the old torque (45+/5Nm Direct torque). The new torque is Angle controlled torque monitor (20Nm Snug torque, 110 deg Angle, monitor torque within 40-70Nm). Please use Service Library for your reference."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Frt Stabilizer assembly BSR from the front end due to Smartbar (disconnecting front sway bar). Root cause was identified as anti-rotation bracket (connects the actuator to the stabar) coming loose due to inadequate clamp load at the joint and weld (holds the bolt shaft and bracket flange) was poorly designed. If any vehicle causes BSR because of this Bracket failure (loose joint/ bracket bends) DO NOT replace whole stabar assembly, instead replace with the service kit (PN#68730602AA). Dealer must need to order the parts from part ordering system for this claim. This kit contains 1 bracket (PN 68730603AA), 3 M10 Nut (PN 68730605AA), 2 M8X1.5 Bolt (PN 68730606AA) and 2 M10X1.5 bolt (PN 06513427AA). 1 M10 Bolt (PN 68730607AA). This kit will also contain a new torque instruction for the bolt which holds the clamp bracket to this failed anti-rotation bracket. DO NOT apply the old torque (45+/5Nm Direct torque). The new torque is Angle controlled torque monitor (20Nm Snug torque, 110 deg Angle, monitor torque within 40-70Nm). Please use Service Library for your reference."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Driver Door Seat Massage Switch Inoperative Customers may comment on the following: ● The seat massage switch located on the driver door does not work. (Seat massage system still operates via the radio). This bulletin involves inspecting the left front door seat massage switch operation and possibly replacing the left front door wiring harness."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates This bulletin involves updating the BPCM with the latest available software. **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● **P0B24-00 - Hybrid/EV Battery ""A"" Voltage Unstable. ● P1C5E-00 - Hybrid/EV Battery State Of Health Failed. ● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. ● P0DAB-00 - Hybrid/EV Cell Balancing Performance.** ● P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed. Customers may also experience the following: ● The vehicle will not start."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P1614-00 - ECU Reset/Recovery Occurred. ● P0810-00 - Clutch Position Control Error. Customers may also comment on one or more of the following: ● Customer may not continue with rock cycle maneuver due to the wrong message ""Shift To P then Desired Gear"" displayed on the Instrument Panel Cluster (IPC). ● K0 Adaptation routine runs when vehicle stationary and EV Mode. ● Vehicle loses propulsion capability. ● Service transmission warning indicator is on. NOTE: Requires key cycle to recover. This bulletin involves reprogramming the TCM with the latest available software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0C19 - Drive Motor A Torque Delivered Performance. ● P1B03 - Resolver Signal / MCPA Rationality. ● B273C - Digital Crash Input. Customers may experience the following: ● Intermittent wrench (service HV) icon condition. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP KIT Transmission oil if replacing PHEV Electric Oil Pump for an electrical DTC - do not replace pan and filter as part of repair. The pump is available on its own. Pan and filter replacement are not necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Turbocharger Kit Please note many parts of the Turbo Assembly can be serviced separately and complete turbo replacement may not be necessary. If the Turbo is being replaced for a noise or a rattle, inspect the wastegate for binding. The actuator kit is serviced separately. If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed oring for a leak. The o-ring is serviced separately
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Radio Frequency Hub Module (RFHM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● B1A10-00 - RKE FOB 1 Battery Low. ● B1A11-00 - RKE FOB 2 Battery Low. ● B23D7-14 - Gated Park Control - Circuit Short To Ground Or Open. Customers may also experience one or more of the following: ● Vehicle won’t start unless the fob is pressed to KIN. ● Key fob not detected when inside vehicle. ● Passive Entry (PE) intermittently inoperative. ● Keyless Ignition Node (KIN) unresponsive. ● Welcome feature does not activate at times. This bulletin involves updating the RFHM module with the latest available software"