2021 Jeep GRAND CHEROKEE Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 1,320, ordered newest first. Dated records on this page: May 5, 2024–Mar 28, 2025.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 28, 2025Service Bulletin/Repair Instructions
9100534
NHTSA communication ID: 11016061
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"MODULE Steering Control Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Kit For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Radio USB update to U33.43 Customers may experience one or more of the following: ● Unable to select the Turn by Turn Navigation. ● Blank Performance Pages (Rearview Camera (RVC) Functions Normally). ● Android Auto® Voice Recognition (VR) inoperative. ● Media tuner delayed. ● Charge Schedule not accepting updates via phone (RVC Functions Normally). ● Ambient light inoperative. ● Map in Instrument Panel Cluster (IPC) inoperative. ● Media Widget blank. ● Navigation map black. ● Off-Road Pages inoperative (RVC Functions Normally). ● VR inoperative. ● Incorrect song title displayed (Carplay® only). ● Radio display switches from Media Page to Home Page (RVC Functions Normally). ● Ghost touch on Navigation screen (RVC Functions Normally). ● Widgets missing. ● New User Profile does not load. ● Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally). REPAIR SUMMARY: This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio’s current software level the radio may need a one or two USB update."
NHTSA source summary · Original PDF not reviewed by Recallfolio
LOWER ACTIVE GRILL SHUTTER If the upper or lower AGS seems to be inop please make sure you CLEAR the DTCs BEFORE swapping the old AGS for a new one, and test if the error code returns. Very often the wiring harness presents corrosion, so make sure to check it for any damage BEFORE swapping the AGS. Corrosion in the harness disrupts communication with the AGS, which sets up the DTCs for AGS performance and lights the CEL. If the AGS is inop and it will be replaced and sent back to Stellantis also send back the wiring harness with it. Make sure to fully perform the PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE as indicated in the service library.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Extended Crank Condition Due To Loss of Fuel Pressure Customers may experience the following: ● Extended engine crank condition. This bulletin involves performing a fuel pressure test and possibly replacing the fuel pump module."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. "
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
FUEL PUMP/LEVEL UNIT MODULE For vehicles with Saddle Fuel Tanks, need to determine if there are any DTCs in wiTECH. Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADREST Incoming Vehicles with Deployed Active Head Rest (AHR) should have a through enquiry. If there is no Broken Pieces or Electrical failure, Direction to follow the RESET Procedure in service Library to RESET the AHR
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"R1H Radio T27.38 USB Software Update Customers may experience one or more of the following: ● Uconnect phone improvements. ● Incorrect Navigation units shown. ● Navigation feature shows no road name with a straight road at times when not setting up a navigation route. ● Missing radio stations. ● Accessibility settings are missing. ● Incorrect phone widget. ● Radio freezes. ● The Hybrid/EV screen display is blank when the user switches to the dark mode theme. ● Hybrid/EV pages are inoperative. ● Radio display is off when starting the vehicle. The display will restore to normal operation after roughly one minute of run time. (Rearview Camera (RVC) Functions Normally). ● Radio screen is black (RVC Functions Normally). ● USB mode changes on its own. ● Remotely Operated Vehicle (ROV) Firmware Over The Air (FOTA) scheduling improvements. ● Apps downloaded for one connected profile are being shared with other local profiles. ● Profile creation process is slow to respond. ● Camera soft-keys are slow to respond when selecting the reverse or forward camera displays. ● The FamCam ""X"" button is missing. ● SiriusXM radio resets. ● Radio resets. ● The RVC zoom feature lags. ● Voice Recognition (VR) is stuck in listening mode. ● Android Auto® resets. ● Android Auto® disconnects. ● Apple® CarPlay® disconnects. ● Missing battery voltage information. ● Rear Seat Alert (RSA) reminder is inoperative. ● The menu bar is missing from the display. ● The Wi-Fi application is missing. ● Music playback is inoperative. ● Invalid FOTA pop-up message displays. ● The Assisted Call features audio is inoperative. This bulletin involves updating the R1H radio software level to T27.38. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Powertrain Control Module (PCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P2066 - Fuel Level Sensor 2 Performance. Customers may experience one or more of the following: ● When the driver attempts to override the Electric Park Brake (EPB) while it remains engaged due to an unbuckled seatbelt in Drive or Reverse, the high torque request with the park brake engaged may lead to a damaged or broken Rear Drive Unit (RDU). ● MIL illuminates when fueling the vehicle while the engine is running. ** ● Lower fuel economy reported by the Instrument Panel Cluster (IPC). ● Rough engine idle during warm up. ● Vehicle turns off while idling in park. In addition, the following software enhancement is available: ● Improved Security. This bulletin involves reprogramming the PCM with the latest available software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses."
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cluster and Radio Display Settings Revert Back to Default Settings, Auto Door Locks and Paddle Shifter Inoperative With No Menu to Enable, Pedestrian Emergency Brake (PEB) Lamp and Forward Collision Warning (FCW) Lamp on After a Recent Service Repair no Diagnostic Trouble Codes (DTCs)
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Kit TSB 21-039-24 REV A - D-Clutch repair kit missing Carrier Output Shaft Seals It has been identified the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Security Gateway Module Battery Voltage - Circuit Voltage Below Threshold - DTC B2199-16 Repair Action : 1) Check OR Replacing cabling. 2) Check OR Replacing connector. 3) Check the battery is good OR Replacing battery. 4) Check OR Replacing FUSE. 5) Check SGW terminal. Battery Voltage - Circuit Voltage Above Threshold - DTC B2199-17 Repair Action : 1) Check OR Replacing cabling. 2) Check OR Replacing connector. 3) Check the battery is good OR Replacing battery. 4) Check OR Replacing FUSE. 5) Check SGW terminal. CAN Bus- [C-CAN1] (Node mute) or CAN Bus Off Performance- (Bus off failure) - Check DTC in DTC matrix Repair Action: 1) CAN Lines Check 2) Read Fault memory of all nodes 3) Check and download the right calibration file for current vehicle configuration Ethernet Bus Failure - Check DTC Repair Action: 1) CAN Lines Check 2) Read Fault memory of all nodes 3) Check and download the right calibration file for current vehicle configuration ECU-In-Plant-Mode - B235A-00 Repair Action: Install Calibration file with correct policy Ecu Internal Performance - Internal Electronic Failure - DTC B22A9-49 Repair Action: 1. If its in store clear and check again if DTC shows up. 2. Check battery voltage 3. Issue still exist then change ECU ECU Not Programmed / Flash Required (No Valid Application) - DTC C221C-00 Repair Action: 1. Reflash ECU with correct file Control Module Security Certificate Missing/Invalid - DTC U3033-00 or U3033-01 Repair Action: 1. Check connectivity 2. Ethernet network 3. Flash with the latest FOTA App Code 4. Flash the cert store with correct certificate 5. Clear Faults
NHTSA source summary · Original PDF not reviewed by Recallfolio
FPDM Please DO NOT immediately replace the display, Please follow the following steps. 1. Perform a vehicle battery disconnect to reset the display. Then check the Display function. If Display is still black, replace the display. 2. If screen is recovered, perform a radio Factory reset through the Display. Go to Vehicle menu > Settings > Reset > Factory reset. 3. Then Perform 2 full Ignition Key cycles and check display function. Turn the vehicle off, then open the door and close the door. Then wait until the cluster goes completely off before turning on the car again. 4. If still having screen issues, replace the Display.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Mid - Range Radar Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C00C4-49 Rear Radar Module 'A' - Internal Electronic Failure. Customers may also experience the following: ● Blind Spot Warning Mid Range Radar warning light on in instrument cluster. This bulletin involves replacing the rear Mid - Range Radar Module."
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING · FORWARD COLLISION AVOIDANCE: WARNINGS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
MODULE Occupant Restraint After Battery Drainage ORC do not work. Please follow the following steps. 1. Check ORC proxi, if the ORC is not aligned, perform proxi alignment, reset module. 2. If proxi is correct, reset module 3. Check for DTCs, and check wiring and components related to those DTCs and clear them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."