The manufacturer’s record · Page 7 of 26
Original record summaries, dates and identifiers for this model-year. Records 601–700 of 2,541, ordered newest first. Dated records on this page: Sep 18, 2019–Apr 28, 2020.
Back to 2015 Chevrolet SUBURBAN problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10175853
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10175853 at NHTSANHTSA communication ID: 10174864
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10174864 at NHTSANHTSA communication ID: 10174861
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10174861 at NHTSANHTSA communication ID: 10174859
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
Source components: ELECTRICAL SYSTEM.
Source record 10174859 at NHTSANHTSA communication ID: 10174851
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the door striker cover will be shipped with the vehicle from the assembly plant. Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.
Source components: STRUCTURE.
Source record 10174851 at NHTSANHTSA communication ID: 10175855
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:BODY.
Source record 10175855 at NHTSANHTSA communication ID: 10174818
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
Source components: ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC).
Source record 10174818 at NHTSANHTSA communication ID: 10175852
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10175852 at NHTSANHTSA communication ID: 10174304
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10174304 at NHTSANHTSA communication ID: 10173728
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · LANE DEPARTURE: BLIND SPOT DETECTION.
Source record 10173728 at NHTSANHTSA communication ID: 10174302
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10174302 at NHTSANHTSA communication ID: 10173714
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, ELECTRIC.
Source record 10173714 at NHTSANHTSA communication ID: 10173713
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Trailer Brake message in the Driver Information Center. Also the vehicle will have a Diagnostic Trouble Code U0415 set. Technician will fill the master cylinder brake fluid reservoir to the maximum level.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, ELECTRIC.
Source record 10173713 at NHTSANHTSA communication ID: 10173712
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a water leak in in the second and third row seating area. Inspect the C-pillar which is the body vertical structure behind the rear passenger door area of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.
Source components: STRUCTURE.
Source record 10173712 at NHTSANHTSA communication ID: 10174303
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10174303 at NHTSANHTSA communication ID: 10174305
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.
Source components: ENGINE AND ENGINE COOLING.
Source record 10174305 at NHTSANHTSA communication ID: 10174306
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
Source components: BACK OVER PREVENTION · ENGINE.
Source record 10174306 at NHTSANHTSA communication ID: 10173681
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
Source components: TIRES · TIRES:SIDEWALL.
Source record 10173681 at NHTSANHTSA communication ID: 10173680
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
Source components: SUSPENSION.
Source record 10173680 at NHTSANHTSA communication ID: 10174299
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
Source components: EQUIPMENT.
Source record 10174299 at NHTSANHTSA communication ID: 10174300
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
Source components: TIRES.
Source record 10174300 at NHTSANHTSA communication ID: 10174301
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10174301 at NHTSANHTSA communication ID: 10174307
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10174307 at NHTSANHTSA communication ID: 10173627
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
Source record 10173627 at NHTSANHTSA communication ID: 10173626
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates repair information for the rear vision camera or surround vision camera image being: - Yellow - Blurry - Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
Source components: BACK OVER PREVENTION.
Source record 10173626 at NHTSANHTSA communication ID: 10173625
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the alarm sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver?s door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver?s door remains open the alarm will not turn back on and the new transmitters can be programmed.
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10173625 at NHTSANHTSA communication ID: 10173416
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
Source components: ENGINE · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10173416 at NHTSANHTSA communication ID: 10173398
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
Source components: ENGINE · EQUIPMENT.
Source record 10173398 at NHTSANHTSA communication ID: 10173393
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:BODY.
Source record 10173393 at NHTSANHTSA communication ID: 10173415
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10173415 at NHTSANHTSA communication ID: 10173414
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES.
Source record 10173414 at NHTSANHTSA communication ID: 10172811
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this occurrence.
Source components: ENGINE · FUEL SYSTEM, DIESEL.
Source record 10172811 at NHTSANHTSA communication ID: 10172334
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a pop, click, tick, snap, or itch type noise in the steering column or steering wheel when turning left or right during low speeds or parking maneuvers. Technician will need to inspect for mis-routed airbag module wiring harness for contacting vibration damper plate in steering wheel, or replace the column upper bearing inner race, spring, and seat.
Source components: AIR BAGS · ELECTRICAL SYSTEM · STEERING.
Source record 10172334 at NHTSANHTSA communication ID: 10172325
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES · SUSPENSION.
Source record 10172325 at NHTSANHTSA communication ID: 10173418
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S. Only).
Source components: EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10173418 at NHTSANHTSA communication ID: 10173417
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.
Source components: EQUIPMENT · WHEELS.
Source record 10173417 at NHTSANHTSA communication ID: 10172773
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10172773 at NHTSANHTSA communication ID: 10172784
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
Source components: ENGINE · EQUIPMENT.
Source record 10172784 at NHTSANHTSA communication ID: 10172777
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace both fuel feed lines for a leak and/or noise coming from pulses in the fuel line.
Source components: FUEL SYSTEM, OTHER.
Source record 10172777 at NHTSANHTSA communication ID: 10172305
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
Source components: EQUIPMENT.
Source record 10172305 at NHTSANHTSA communication ID: 10172884
NHTSA source summary · Original PDF not reviewed by Recallfolio
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.
Source components: ELECTRICAL SYSTEM · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
Source record 10172884 at NHTSANHTSA communication ID: 10172883
NHTSA source summary · Original PDF not reviewed by Recallfolio
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.
Source components: ELECTRICAL SYSTEM · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
Source record 10172883 at NHTSANHTSA communication ID: 10171318
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
Source components: ELECTRICAL SYSTEM.
Source record 10171318 at NHTSANHTSA communication ID: 10172294
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
Source components: EQUIPMENT.
Source record 10172294 at NHTSANHTSA communication ID: 10171896
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition.
Source components: ENGINE.
Source record 10171896 at NHTSANHTSA communication ID: 10172293
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
Source components: EQUIPMENT · WHEELS.
Source record 10172293 at NHTSANHTSA communication ID: 10171875
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
Source record 10171875 at NHTSANHTSA communication ID: 10172285
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
Source components: EQUIPMENT.
Source record 10172285 at NHTSANHTSA communication ID: 10171888
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10171888 at NHTSANHTSA communication ID: 10171280
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Source components: ENGINE AND ENGINE COOLING.
Source record 10171280 at NHTSANHTSA communication ID: 10171265
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
Source components: ENGINE AND ENGINE COOLING.
Source record 10171265 at NHTSANHTSA communication ID: 10171264
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
Source record 10171264 at NHTSANHTSA communication ID: 10171259
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10171259 at NHTSANHTSA communication ID: 10171878
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM.
Source record 10171878 at NHTSANHTSA communication ID: 10170483
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
Source components: TRAILER HITCHES.
Source record 10170483 at NHTSANHTSA communication ID: 10170498
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
Source components: EQUIPMENT.
Source record 10170498 at NHTSANHTSA communication ID: 10170426
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures.
Source components: SEATS.
Source record 10170426 at NHTSANHTSA communication ID: 10170424
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
Source components: SERVICE BRAKES.
Source record 10170424 at NHTSANHTSA communication ID: 10169357
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10169357 at NHTSANHTSA communication ID: 10169271
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10169271 at NHTSANHTSA communication ID: 10169355
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10169355 at NHTSANHTSA communication ID: 10168978
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
Source components: POWER TRAIN.
Source record 10168978 at NHTSANHTSA communication ID: 10168975
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168975 at NHTSANHTSA communication ID: 10169270
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to add PET tape to the brake cables if the cause of the customers concern.
Source components: SERVICE BRAKES.
Source record 10169270 at NHTSANHTSA communication ID: 10169340
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE.
Source record 10169340 at NHTSANHTSA communication ID: 10169315
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away.
Source components: ENGINE.
Source record 10169315 at NHTSANHTSA communication ID: 10169309
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides information for rebuilding fuel injectors in the event of an underhood fuel odor and/or extended cranking condition.
Source components: ENGINE · FUEL SYSTEM, GASOLINE.
Source record 10169309 at NHTSANHTSA communication ID: 10169356
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · TIRES · WHEELS.
Source record 10169356 at NHTSANHTSA communication ID: 10169354
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EXTERIOR LIGHTING.
Source record 10169354 at NHTSANHTSA communication ID: 10168964
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10168964 at NHTSANHTSA communication ID: 10168960
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Source components: SERVICE BRAKES, AIR:ANTILOCK · WHEELS.
Source record 10168960 at NHTSANHTSA communication ID: 10168959
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection. If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168959 at NHTSANHTSA communication ID: 10168956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
Source components: ELECTRICAL SYSTEM.
Source record 10168956 at NHTSANHTSA communication ID: 10168212
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
Source components: POWER TRAIN.
Source record 10168212 at NHTSANHTSA communication ID: 10168181
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the radio for vehicles with the condition of Intermittent Pop Noise from the Speakers Followed by a Reset of the Radio and Clock due to a software issue.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL.
Source record 10168181 at NHTSANHTSA communication ID: 10167466
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
Source components: ELECTRICAL SYSTEM.
Source record 10167466 at NHTSANHTSA communication ID: 10167465
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates if the sunroof, rear sliding window, and/or wireless charging are found to be inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.
Source components: ELECTRICAL SYSTEM · VISIBILITY.
Source record 10167465 at NHTSANHTSA communication ID: 10167463
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up. This information advises dealers on how the seat functions and also a common area where an open circuit may be found between the third row seat module and the seat position sensor. It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well as advising the dealer to look for bent/damaged seat recline mechanisms.
Source components: ELECTRICAL SYSTEM.
Source record 10167463 at NHTSANHTSA communication ID: 10167462
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
Source components: ELECTRICAL SYSTEM.
Source record 10167462 at NHTSANHTSA communication ID: 10167460
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
Source components: LANE DEPARTURE.
Source record 10167460 at NHTSANHTSA communication ID: 10167459
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold. If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.
Source components: ENGINE AND ENGINE COOLING.
Source record 10167459 at NHTSANHTSA communication ID: 10167455
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
Source components: EQUIPMENT.
Source record 10167455 at NHTSANHTSA communication ID: 10168207
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168207 at NHTSANHTSA communication ID: 10167439
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.
Source components: ELECTRICAL SYSTEM.
Source record 10167439 at NHTSANHTSA communication ID: 10168175
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: POWER TRAIN.
Source record 10168175 at NHTSANHTSA communication ID: 10167437
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Source components: ENGINE.
Source record 10167437 at NHTSANHTSA communication ID: 10168185
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10168185 at NHTSANHTSA communication ID: 10167479
NHTSA source summary · Original PDF not reviewed by Recallfolio
N182202780 01 - Special Coverage. Certain Vehicles may have a condition where customers may experience increased brake pedal effort, hardbrake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applyingthe brakes. The engine mounted mechanical vacuum pump outputmay decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervalscould contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs,the hydraulic brake system remains functional but may require additionalpedal force. Please be aware that even if the vehicle exhibits this condition, it meets all federal motor vehicle safety standards forbrake performance. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.
Source components: ENGINE AND ENGINE COOLING · SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE.
Source record 10167479 at NHTSANHTSA communication ID: 10167434
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
Source components: ELECTRICAL SYSTEM.
Source record 10167434 at NHTSANHTSA communication ID: 10168208
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on key code security and information on GM key code look up applications.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168208 at NHTSANHTSA communication ID: 10168205
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168205 at NHTSANHTSA communication ID: 10168204
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168204 at NHTSANHTSA communication ID: 10168188
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168188 at NHTSANHTSA communication ID: 10166665
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational Bulletin provides information on availability of Diesel Fuel additives.
Source components: FUEL SYSTEM, DIESEL.
Source record 10166665 at NHTSANHTSA communication ID: 10165920
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with erratic or hesitation when opening and closing the power liftgate. There may be a diagnostic trouble code B153A set in the power liftgate module. This concern could occur if the left liftgate actuator is internally coming apart. The actuator will need to be replaced however care must be taken when removing the actuator from the vehicle. If the internal portion of the actuator had completely separated the end of the actuator could become a projectile when removed. Obtain a number 8 self-tapping screw that measures 1 ½ inches long. Fully open the liftgate and install the screw anywhere in a 30 millimeter space from the bottom of the smooth tube to secure the tubes. Continue with the liftgate actuator by following the liftgate power assist actuator procedure in service information.
Source components: STRUCTURE:BODY:HATCHBACK/LIFTGATE.
Source record 10165920 at NHTSANHTSA communication ID: 10165914
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165914 at NHTSANHTSA communication ID: 10165905
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
Source components: STRUCTURE.
Source record 10165905 at NHTSANHTSA communication ID: 10165904
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
Source components: ELECTRICAL SYSTEM.
Source record 10165904 at NHTSANHTSA communication ID: 10166659
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
Source components: ENGINE AND ENGINE COOLING.
Source record 10166659 at NHTSANHTSA communication ID: 10166638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
Source components: EQUIPMENT.
Source record 10166638 at NHTSA