2011 Chevrolet SILVERADO 2500 Manufacturer communications & TSBs.Page 13
Original record summaries, dates and identifiers for this model-year. Records 1,201–1,300 of 1,568, ordered newest first. Dated records on this page: Jul 12, 2013–Feb 24, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 24, 2014Service Bulletin/Repair Instructions
PIP5168B
NHTSA communication ID: 10111956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Drive Motor Generator Control Module, also known as PIM) for the 2-Mode Hybrid Utilities and Trucks are being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure to repair the joint being loose or out of position for the turbocharger to turbocharger exhaust pipe or turbocharger exhaust pipe exhaust downpipe connection, to correct the customers concern of Exhaust Leak or Vibration/Rattle Noise at Approximately 900 RPM, Fuel Smell, White Smoke, Oily Substance on Exhaust Downpipe.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides service information to the dealer technicians that the remote start will not work with the ONSTAR REMOTE Link applcation
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that First Responder Guides for General Motors vehicles can be accessed via the web at http://www.gmstc.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to inspect the transmissions filter for splits or cracks to correct the customers concern for no forward, reverse or slips.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a cold engine tick noise for 50 seconds at start up. Technician determines if the tick noise is possibly coming from the exhaust manifold, as this noise could easily be mistaken for an engine tick noise. If your SI diagnosis does not isolate the cause of this concern, this concern should be considered a vehicle design characteristic of the ECM calibration and no additional repairs should be performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 6.6L Diesel Engine Fuel Injection Pump part numbers 12645102 and 12658095 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B15517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER · POWER TRAIN:CLUTCH ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the passenger presence system, passenger air bag on/off indicators, passenger air bag on/off switch, and passenger seat belt indicator. Dealer can review and explain the options that are equipped with the vehicle in question.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an aftermarket, add-on back up alarm will sound when unlocking the doors with the Remote Keyless Entry remote. Technician can correct this concern by turning off the perimeter lighting feature on vehicles with Driver Information Center controls or install an isolation relay in-line to the backup alarm.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frame Labels Visible from Outside of Vehicle Some customers may comment on disliking the appearance of the white labels that are visible on the frame The frame labels are only required during the manufacturing process and can be removed during pre-delivery inspection (PDI). There are two labels on the frame: the left front label (1) visible underneath the driver's door and the right front label (2) visible through the wheelhouse. Use care when removing the labels to prevent damage to the wax coating on the frame. Use a plastic trim tool to lift up on the edge and then pull the label off. The time required to perform this action is included in the PDI base time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is a revision of 10-06-01-008I to add the 2010-2012 Chevrolet Colorado and GMC Canyon, RPO LH9 and update the Labor Operation to the Global Labor Code (GLC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information on Exhaust Fluid Range, Exhaust Fluid Quality Poor, Service Exhaust Fluid System or Service Emission System Driver Information Center Messages
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. If Service Information diagnosis isolates no compression on the misfiring cylinder(s) with 100% leakage into the crankcase, perform the following steps as necessary before disassembling the engine. Technician will use a lighted bore scope if available to inspect the top of the related piston(s) through the spark plug hole to determine if any of the pistons are melted. If damaged piston(s) are found inspect for aftermarket parts. Also use the latest version of 09-06-04-026 to verify if there are aftermarket calibrations in the Engine Control Module. Take photos and document accordingly if anything is found.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. Technician should use Published Service Information for fuel system cleaning.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Valve Assembly part number 24255209 and Valve Body part number 29544409 have been removed from the General Motors Product Quality Center parts restriction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
Source components: STEERING:LINKAGES:ARM:IDLER AND ATTACHMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure to remove, update and reinstall the rear side door window reveal molding due to the exterior paint finish is chipped, cracked or scratched around the rear corners of the rear side door window outer sealing strip (reveal molding).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Duramax Diesel Engine Fuel Injection Pump Part number 12645102 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.