2012 Chevrolet CAMARO Manufacturer communications & TSBs.Page 10
Original record summaries, dates and identifiers for this model-year. Records 901–1,000 of 1,892, ordered newest first. Dated records on this page: May 15, 2015–Dec 1, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Dec 1, 2015Service Bulletin/Repair Instructions
PIP5216D
NHTSA communication ID: 10114939
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If a vehicle comes into the dealership with a knock noise, seized engine, lower end squeak or squeal or any condition that you suspect a rod or main bearing failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with water that may be leaking into the vehicle and accumulate in the rear floor pan area on either the left or right side of the vehicle. Technician will need to verify that the plastic water diverter that is sewn into the top is on the "wet-side" of the trim. Technician should also verify the front of the water management bag is properly attached to the body sheet metal panel then inspect the front drains for proper installation. Technician should also verify the presence and proper location of the foam tape on both the left and right side 5 bow brackets. Inspect the area of the vehicle where the folding top frame is fastened in place, if there is no visible seam sealer on the side of the vehicle that has the leak, this may be the cause for the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water may leak into the vehicle and accumulate in the rear floor pan area on either the left or right side of the vehicle. This could be caused by any of the following issues described below. Be sure to read over all possible areas of concern listed below.
Source components: STRUCTURE:BODY · STRUCTURE:FRAME AND MEMBERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may comment that the vehicle has reduced acceleration at low speed and/or transmission is slipping from a launch. Technicians may find DTC P0751 set or stored in history. This condition may be caused by the Clutch Select Solenoid Valve 2 (359), located in the lower valve body, sticking in its bore resulting in a 4th gear start. Note: This condition can be very intermittent and difficult to duplicate.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a large gap between the #5 bow and the rear "tulip" panel when the top is closed and latched. Technician should replace the #5 bow as well as both LH and RH Folding Top Pivot Brackets.
Source components: EQUIPMENT · STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that exhibits a squeal noise. The front or rear brakes and typically are heard during slow stops. Dealer should communicate to the customer that these conditions are normal operating characteristics of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
Source components: STRUCTURE:FRAME AND MEMBERS · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a belt squeak noise and/or a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.40mm, replace the crankshaft balancer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a Antilock Braking System Malfunction Indicator Lamp on. Technician will find the scan tool will not communicate with the Electronic Brake Control Module. Technician will check the Yaw and Lateral Accelerometer Sensor and the Steering Wheel Angle Sensor supply voltage circuit 2087 Dark Green shorted and pulling down the internal circuitry of the Electronic Brake Control Module. Not all vehicles use circuit 2087 to supply voltage to the Steering Wheel Angle Sensor, so be sure to check Service Information for the specific vehicle that is being serviced. If circuit 2087 is backed out of the EBCM connector and communication returns, inspect for either this circuit being shorted to ground or for a sensor concern. Technician will repair the circuit as necessary and reroute to prevent the concern from reoccurring. If the technician is working on a full-size or utilities that have aftermarket lift kits the wheel speed sensor may be broken or shorted. Technician will repair the circuit as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15030 - Special Coverage. On some 2010-2013 model year Chevrolet Camaro vehicles, the license-plate lamp housing-retention features could fracture off the housing. If this occurs, the bulb socket could move out of its original-design location, which could cause an illuminated bulb to touch and melt the lamp housing and the adjacent rear bumper fascia cover. The hot rear bumper fascia cover, or the hot bulb itself, depending on the severity of the melting, could come into contact with someone who is loading or unloading the trunk. Dealers are to replace the current license plate lamp housings with a new housing and repair any damage to the rear fascia.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a misfire event that usually occur at speeds of 70 miles per hour, 3rd Gear, and 3500 ? 4500 revolutions per minute. Dealer should advise customer to refer to TopTierFuel.com for availability in their respective area and fill with 91 or higher octane level fuel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about iPhones will not always autoconnect through Bluetooth to the vehicle. If the vehicle has more than one device listed in the Bluetooth device list, and the last device used was an Apple product, the Apple products will not autoconnect. The system will connect to one of the other devices instead. This concern is usually noticed after Retained Accessory Power has cancelled and the vehicle has gone to sleep. Advise the customer that they will need to update their Apple device to the latest operating system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about some vehicles that may have a concern of Bluetooth music skipping. This condition is a normal operating characteristic of the vehicle. Streaming music through Bluetooth uses a lot of the radio's processing resources. If the radio is also dedicating a large amount of resources to other applications such as navigation, booting, or XM Weather the Bluetooth audio may hesitate/skip as the system is being heavily loaded.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. Inspect the engine for any oil leaks and repair if need. Technician should change the engine oil and replace the oil filter using a PF48e type filter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of diagnostic instructions to take when the key will not fold into the fob or will not stay in the folded position. The technician may comment that the key in the fob will not fold close or stay latched closed. Damage to the folding mechanism could result from storing the key in the door lock cylinder and accidently bumping or making contact with the key fob. Please advise all dealer personnel to refrain from storing the key in the door lock even for brief periods.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of "Top Not Secure" message displayed in the DIC, even when driving and the folding top is closed/secure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
Source components: EQUIPMENT:ELECTRICAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2015-2016 model years to repair information to correct a customer concern of inaccurate or slow response of outside air temperature display.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians a general guideline for inspection of the convertible water management bag, anytime the folding top is removed .
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides dealership personnel/customers Information on convertible top operation below 0C (32F) in snow, rain or after wet conditions-possible ice formation in water management bag.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information on convertible top water management bag repair or replacement, to correct a customer concern of finding water in the trunk of the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have sloshing noise while stopping. Technician will need to add or remove 3 gallons of fuel in the fuel tank and retest. If the noise is gone after changing the fuel level then there is nothing you can do to change this condition. The noise is considered normal for that level of fuel in the tank. If the noise is present with all fuel levels, inspect for a blocked drain hole in the mufflers. Technician will need to clean out the drain hole to correct the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a UPF48R if one is available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a PF48 if one is available. If there is no availability of oil filter PF48 use oil filter UPF48R.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of a customer concern where the heated seat indicator light is not functioning or the heated seats are not up to operating temperature during a remote vehicle start event. This is normal operation of the heated seat during a remote vehicle start event. The electronic climate control module is not in a complete wake up state during a remote vehicle start mode and will not enable the light emitting diode. After a cold soak below 32 degrees Fahrenheit the seat will not get hot in the 10 minutes or less of the remote vehicle start mode. This is due to the fact that the heat element is not in direct contract with the seat surface while the seat is unoccupied and the foam below the heater is full cold insulating air which takes time to heat up. Technician is to communicate to the customer this condition is a normal operating characteristic of their vehicle. It will not impact the designed performance or reliability of the vehicle. Please share this information with the customer, including a copy of this message.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with the following steps to correct a moan noise from the rear axle during cold turning maneuvers. This noise might start to be noticed as the vehicle accumulates over 3000 miles. The technician is to perform the following steps. 1. With original lube in axle, conduct Freeway Speeds for 10 miles to warm up lube. 2. Immediately drain original lube and refill with fresh lube. 3. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 4. . In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 5. Perform 4 Figure 8?s at (5-10 mph). 6. Freeway Speeds for 20 miles until operating temperature is achieved. 7. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 8. In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 9. Perform 4 Figure 8?s at (5-10 mph). 10. Immediately drain current lube in axle and refill with fresh lube. 11. Perform Steps 3 thru 9 again. 12. Immediately drain current lube in axle and refill with fresh lube. Proceed with steps 2 through 9 two times, for a total of 3 drain and fill procedures. This should only be done for a moan noise from the rear axle during cold start turning maneuvers. During regular maintenance the fluid only needs to be changed one time.