Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 2,093, ordered newest first. Dated records on this page: Mar 30, 2015–Oct 5, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 5, 2015Service Bulletin/Repair Instructions
08-08-44-029E
NHTSA communication ID: 10126350
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles with a rattle, tick, or knock type noise. Technician will use chassis ears to listen to the right and left side of the engine and isolate which bank the noise is from. Technician should now remove the piston and rod assemblies from the affected bank to inspect for a loose rod bushing in the rod, or a loose wrist pin in the bushing. There should be no metal through the oil and a piston and rod assembly will repair this noise. If technician finds metal refer to the latest version of PIP5216. If no wrist pins or bushings are found loose and all other diagnostics for this type of noise has been exhausted then engine replacement may be necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician will need to perform a Multi Axis Sensor yaw rate sensor learn procedure. Also perform the Long Range Radar Learn called-out in the Radar Sensor Module - Long Range Programming and Setup procedure in Service Information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to access XM Weather. If the system responds by highlighting the XM Weather Icon but it does not enter the application technician should replace the Human Machine Interface module for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
Source components: LANE DEPARTURE: ASSIST · LANE DEPARTURE: WARNING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a brake pedal may not raise or seem stuck down after a normal braking event. Technician will need to replace the brake pedal arm.
Source components: SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides diagnostic and repair information to correct a customer concern of IPC gauges sweep, loss of power steering assist, intermittent no crank, reduced engine power and multiple U-codes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: BRAKE PEDAL DOES NOT RAISE AFTER APPLY BRAKES REMAIN APPLIED OR BRAKE LIGHTS ON UNWANTED. THE CONDITION MAY OCCUR IN HIGH TEMPERATURE AND HUMIDITY CONDITIONS AND MAY NOT BE REPEATABLE. *JS UPDATED 08/28/2012 *JS UPDATED 10/15/14. *PE UPDATED 2/12/16. *PE
Source components: EXTERIOR LIGHTING:BRAKE LIGHTS · SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin is requesting information from dealers on a customer concern of engine no crank/no start due to discharged battery.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a service column lock message. Technician will find diagnostic trouble code B2897 symptom 05 set as history. Any of the follow scenarios could set the code. 1. Power mode is OFF, OPEN the Driver Door, then press the Ignition Switch within 100ms (power mode changes to ACC or RUN). 2. Power mode is ACC or RUN, the Driver Door is OPEN, then change power mode to OFF, and close the Driver Door within 300ms. 3. Power mode is OFF, then OPEN and CLOSE the Driver Door quickly?in less than 300ms. If these are ruled out as the cause of the code or it is set current follow normal service information diagnostics. If the scenarios are the cause of the concern this is a normal operation, communicate to the customer that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to download the USB software from TIS2WEB using the vehicle identification number every time a programming event of the human machine interface module is needed. Damage could be caused to the module if USB programmed with the incorrect software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin is requesting information from dealers on a customer concern of engine no crank/no start due to discharged battery.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
Source components: EQUIPMENT:ELECTRICAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of intermittent brake squeal or squeak noise on initial brake application.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding original equipment battery part numbers and AC Delco replacement battery approved warranty part numbers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to download the USB software from TIS2WEB using the vehicle identification number every time a programming event of the human machine interface module is needed. Damage could be caused to the module if USB programmed with the incorrect software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a CD player is inoperative. Technician should cycle power to the CD play and retest. If the CD player starts working advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. If the CD player is still inoperative technician will need to test the power and ground circuits. If no concern with power, ground, or connections, replace the Disc Player.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the lower center section of the display will not work when pressed. Technician will need to replace the Integrated Center Stack for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that navigation system has inaccurate estimated time of arrival. This is a normal operating characteristic of the New Generation Infotainment system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a CD player is inoperative. Technician should cycle power to the CD play and retest. If the CD player starts working advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. If the CD player is still inoperative technician will need to test the power and ground circuits. If no concern with power, ground, or connections, replace the Disc Player.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of steps to take if Pandora is inoperative or experiencing intermittent operation. 1. Verify Pandora is installed on the device. 2. Make sure the device is Bluetooth connected and paired to Cadillac CUE. 3. Make sure stations have been created in Pandora on the device. 4. Launch Pandora by selecting the Pandora Icon on the Integrated Center Stack and allow a few moments for the App to start on the device. 5. Make sure the Bluetooth volume on the device is turned up or on. Pandora volume is controlled by the device since it is a Bluetooth application. 6. Pandora is controlled by the devices connection and data signal. If the device has a poor data signal Pandora may not play. 7. If Pandora is successfully working, the device should display "Accessory". 8. Apple devices must be connected via USB to the vehicle to launch Pandora. Customers can use the "Bluetooth" input under the media selection to stream audio but will not have full control of the device using the radio. 9. Some Android phones require a setting in Pandora to allow Pandora to access automotive audio. Launch Pandora on the phone, in Pandora select settings in the upper right hand corner of the screen, select "advanced" and make sure "Bluetooth for Automotive" is checked and enabled. 10. If all of the above tips have been verified, and the message "No Internet Connection" is displayed on the Integrated Center Stack screen, CUE is not picking up the devices internet connection. Ensure that the device has adequate battery life and a good data signal. Check to see if Pandora can be heard through the device itself. If Pandora is playing through the handset device, try repairing the device and/or switching to a different audio screen and coming back to Pandora. 11. If Pandora is installed on a phone and a media device is also connected, such as an IPod that is hardwired to the vehicle, there may be confusion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
14687A - SERVICE UPDATE (REVISED SERVICE PROCEDURE AND WARRANTY TRANSACTION INFORMATION). THE INSTRUMENT PANEL CLUSTER (IPC) ON SOME 2013 MODEL YEAR CADILLAC ATS, SRX AND XTS VEHICLES MAY INTERMITTENTLY FAIL TO OPERATE WHEN THE VEHICLE IS IN THE ON/RUN POWER MODE. VEHICLES WITH THIS CONDITION MAY HAVE INOPERATIVE ANALOG GAUGES OR INDICATOR TELLTALES WHEN THE IGNITION IS IN THE ON/RUN POWER MODE. CYCLING THE IPC FROM A SLEEP STATE TO A WAKE-UP POWER STATE WILL AUTOMATICALLY CORRECT THE CONDITION; CUSTOMERS OR SERVICE TECHNICIANS, HOWEVER, MAY NOT BE ABLE TO REPLICATE THIS CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a service column lock message with a possible diagnostic trouble code B2897 symptom 05 set as history. Any of the follow scenarios could set the code. 1. Power mode is OFF, OPEN the Driver Door, then press the Ignition Switch within 100ms (power mode changes to ACC or RUN) 2. Power mode is ACC or RUN, the Driver Door is OPEN, then change power mode to OFF, and close the Driver Door within 300ms 3. Power mode is OFF, then OPEN and CLOSE the Driver Door quickly?in less than 300ms If these are ruled out as the cause of the code or it is set current follow normal service information diagnostics. If the above scenarios are the cause of the concern this is a normal operation, communicate to the customer that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on a proper paint code for the following special addition vehicles. 2003 Mary Kay Cadillac models - use paint code WA-160E - Mary Kay Pink Pearl 2004 - 2007 Mary Kay Cadillac models - use paint code WA-983L - Mary Kay Pink Pearl III 2004 Neiman Marcus Cadillac XLR - use paint code WA-111B - Majestic Amethyst Metallic 2008 - 2015 Mary Kay Cadillac models - use paint code WA-590Q - Mary Kay Pink Pearl V 2011 Neiman Marcus Chevrolet Camaro convertible - For the exterior body color, use paint code WA-724S - Mystic Bronze Tri-coat. For the ghost stripes on the hood and deck lid, use paint code WA700T 2013 Hot Wheels Chevrolet Camaro - For the exterior body color, use paint code WA-720S - Kinetic Blue. For the red stripe on the wheels and the front bumper, use paint code WA-799U - Performance Red. 2015 Green Flash Camaro models - use paint code WA-136X - Unripened Green
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician when the customer comments that their digital vehicle speed display is showing a different speed than the analog vehicle speed display. There may be up to 2 miles per hour difference between the digital and analog vehicle speed displays. This is a normal condition due to the calculation tolerances being different for the two driver viewing angles for the analog speedometer; it may also appear to increase the difference between both displays. No part replacement is required as this is a normal operating characteristic of the vehicle. For CTS vehicles built between April and June of 2011 or the 2013 ATS, SRX, XTS built before August 29 2012 may have a 3 mile per hour or more variation. The technician is to replace the instrument panel cluster for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with information on a customer concern of the windows roll down unwanted after suing the key fob. The vehicle could have remote venting windows. Normal operation of this feature is to hold the unlock button on the remote keyless entry transmitter until the windows start to roll down. If the unlock button is pressed again the windows will stop. The feature can be turned off if requested by the customer. For the CTS contact Techline to obtain a VCI number to disable the feature. For the XTS reprogram the body control module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a blank radio display. Technician may find a Diagnostic Trouble Code U150F stored in the Radio / Heater-Vent-Air Conditioning controls. Technician will verify if the correct display is installed. If the Diagnostic Trouble Code is current inspect the circuit form end to end.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC: WHILE SOME VEHICLES ARE IN ON/RUN POWER MODE, INSTRUMENT PANEL CLUSTER WILL FAIL TO OPERATE AND ANALOG GAUGES OR INDICATOR TELLTALES BECOMES INOPERATIVE IN THIS CONDITION. MODEL 2013 ATS, SRX, XTS. *PE UPDATED 2/3/16. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a radio screen appears bubbled or is delaminating. Dealer can replace model years 2013 and 2014. If working on a 2015 model year vehicle dealer will need to contact General Motors Technical Assistance Center for further assistance. Technician should replace the Integrated Center Stack with the latest part number out of the parts catalog.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an oily substance is found on the inside windshield surface and appears to be leaking from the rear view mirror area. Technician should inspect the moisture sensor for being the source of the leak, if found to be leaking, carefully remove the moisture sensor. Clean the glass surface and sensor bracket with an isopropanol alcohol wipe until the surfaces are clean, then re-install the moisture sensor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair procedure information to correct a customer concern of Transport Mode On message displayed in Driver Information Center (DIC) and/or battery light is flashing.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to access XM Weather. If the system responds by highlighting the XM Weather Icon but it does not enter the application technician should replace the Human Machine Interface module for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin is requesting information from dealers on a customer concern of low tire pressure indicator illuminated and/or a slow loss of tire pressure.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
14687 - SERVICE UPDATE (STOP PERFORMING UPDATE MESSAGE). GENERAL MOTORS HAS DETERMINED THAT 2013 CADILLAC ATS MODEL VEHICLES EQUIPPED WITH BASE RADIO (RPO RAO WITHOUT UA3) ONLY ARE NOT PROGRAMMING SUCCESSFULLY. UNTIL FURTHER NOTICE, PLEASE STOP PERFORMING THE PROCEDURE CONTAINED IN SERVICE UPDATE BULLETIN 14687 ON THESE VEHICLES. DEALERS MAY CONTINUE TO PERFORM THIS SERVICE UPDATE ON 2013 CADILLAC SRX AND XTS MODEL VEHICLES AND ATS MODEL VEHICLES EQUIPPED WITH CUE RADIOS (RPO RAO WITH UA3).
NHTSA source summary · Original PDF not reviewed by Recallfolio
14687 - SERVICE UPDATE. THE INSTRUMENT PANEL CLUSTER (IPC) ON SOME 2013 MODEL YEAR CADILLAC ATS, SRX AND XTS VEHICLES MAY INTERMITTENTLY FAIL TO OPERATE WHEN THE VEHICLE IS IN THE ON/RUN POWER MODE. VEHICLES WITH THIS CONDITION MAY HAVE INOPERATIVE ANALOG GAUGES OR INDICATOR TELLTALES WHEN THE IGNITION IS IN THE ON/RUN POWER MODE. CYCLING THE IPC FROM A SLEEP STATE TO A WAKE-UP POWER STATE WILL AUTOMATICALLY CORRECT THE CONDITION; CUSTOMERS OR SERVICE TECHNICIANS, HOWEVER, MAY NOT BE ABLE TO REPLICATE THIS CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a blank radio display. Technician may find a Diagnostic Trouble Code U150F stored in the Radio / Heater-Vent-Air Conditioning controls. Technician will verify if the correct display is installed. If the Diagnostic Trouble Code is current inspect the circuit form end to end.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a noise, vibration or shudder on acceleration from a stop. Technician may find that the right front axle shaft is not fully seated into the transfer case. Technician will need to inspect the splines on the half shaft for damage. If damage is found replace the half shaft and install a new retaining ring with part number 90223082. When the half shaft does not have damage to the splines technician should replace the retaining ring with part number 90223082.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to service personnel on the critical importance of installing the correct replacement spin-on oil filter when servicing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a radio display does not always return to the previous call/source screen when a Bluetooth call has ended and/or that the call timer may continue to flash and increment. The call/source screen staying displayed is a normal operating characteristic and cannot be changed. Technician should updated the Human Machine Interface to prevent the call timer from flashing and incrementing after the call has ended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a bind or shudder on turns during tight parking lot maneuvers. If technician is working on a 2012 Lacrosse the Electronic Brake Control Module should be updated with the latest calibrations in Service Programming System. If the technician isolates the condition to be coming from the Rear Drive Module, then check the fluid level in the Rear Drive Module per Service Information. If fluid levels are incorrect then diagnose and repair as needed, review latest version of PI0703 if the differential clutch is overfull. If no fluid concerns are found change the differential clutch oil filter and oil. Technician should insure all oil and debris is removed from the differential.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.