Original record summaries, dates and identifiers for this model-year. Records 1,701–1,800 of 2,405, ordered newest first. Dated records on this page: Apr 20, 2015–Jul 10, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 10, 2015Service Bulletin/Repair Instructions
PIC5491G
NHTSA communication ID: 10114598
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
Source components: EQUIPMENT:ELECTRICAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"15396 - SERVICE UPDATE. THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO INSTALL THE ORIGINAL DESIGN TEMPERATURE-SENSOR WIRING HARNESS TO THE VALVE BODY ON CERTAIN 2015 MODEL YEAR CADILLAC ESCALADE AND ESCALADE ESV; CHEVROLET SILVERADO; AND GMC SIERRA, YUKON, AND YUKON XL VEHICLES. THE SUPPLIER OF THE TRANSMISSION-WIRING HARNESS INTRODUCED AN UNAPPROVED CHANGE TO THE TEMPERATURE SENSOR (THERMISTOR), RESULTING IN INCORRECT OIL-TEMPERATURE READINGS DURING TRANSITION FROM COLD TO WARM TEMPERATURES. THIS COULD CAUSE A HARSH SHIFT WHEN STARTING THE VEHICLE AT TEMPERATURES BELOW 32ºF (0ºC); HOWEVER, SHIFT QUALITY IMPROVES ONCE THE TRANSMISSION OIL WARMS UP."
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, U0268, and/or U0269 stored in the active safety module. Technician should inspect his Multiple Diagnostic Interface cable for damage. Technician should use the Multiple Diagnostic Interface on a like vehicle with Regular Production Option Code Y66 if there are no issues found finish with diagnosing the customer?s concern, if concern is present in the like vehicle replace the Multiple Diagnostic Interface cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC/CADILLAC: ON CERTAIN SUVS/TRUCKS, SERVICE PROCEDURE PROVIDED ON INSTALLING CORRECT TEMPERATURE SENSOR WIRING HARNESS FOR TRANSMISSION DUE TO PREVIOUS WIRING HARNESS WAS UNAPPROVED. MODEL 2015 SIERRA, YUKON, YUKON XL, ESCALADE, ESCALADE ESV, SILVERADO. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: TSB CONTAINS AN OWNER'S NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. ON CERTAIN TRUCKS AND VEHICLES, THE ONSTAR SYSTEM IS INOPERATIVE DUE TO EMBEDDED PHONE FLASH MEMORY CHIP AND VEHICLE COMMUNICATION INTERFACE MODULE (VCIM) NEEDS REPLACING. MODEL 2015. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about when listening to an iPod that the first song will still be displayed when the next song in the list is playing. If this concern is encountered, use the browse button on the radio display and navigate to the desired artist, album, song, or Genre. Once the desired selection is made, the correct information will be displayed on the radio screen.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15414 - SERVICE UPDATE. THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO REPROGRAM THE INSTRUMENT PANEL CLUSTER (IPC) ON CERTAIN 2015 MODEL YEAR CADILLAC ESCALADE AND ESCALADE ESV VEHICLES EQUIPPED WITH THE RPO UDV INSTRUMENT CLUSTER. THESE VEHICLES MAY HAVE A SOFTWARE ANOMALY THAT CAN PREVENT THE VEHICLE FROM ACCURATELY DISPLAYING RPM INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15038 - DEALER MESSAGE ONLY. SELECT 2015 VEHICLES WILL RECEIVE A SOFTWARE DOWNLOAD VIA ONSTAR® TO UPDATE THE SOFTWARE FOR THE ELECTRONIC CLIMATE CONTROL (ECC) SYSTEM. THE UPDATE WILL BE PERFORMED ON DEALER INVENTORY VEHICLES, WITH THE UPDATE OCCURRING DURING THE NIGHT TIME HOURS OF 1AM TO 5AM EDT. UPDATES WILL BE ROLLED OUT TO THE INVENTORY STARTING 6/29/2015 AND COMPLETE BY END OF SEPTEMBER 2015. NO FURTHER ACTION IS REQUIRED BY THE DEALER. THIS UPDATE WILL TAKE APPROXIMATELY 15 MINUTES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a ?Service 4WD Message? displayed in the Driver Information Center. Technician may find Diagnostic Trouble Codes C0392 or C0396. Technician should check the terminal tension on the Transfer Case Control Module X1 connector. Technician should repair any terminal that have poor terminal tension.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding original equipment battery part numbers and AC Delco replacement battery approved warranty part numbers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles with visible water leak or signs of water intrusion from the antenna base, red OnStar LED, unable to connect to OnStar, OnStar unable to locate the vehicle, OnStar has inaccurate global positioning system location, no global positioning system on the navigation radio display, and inaccurate global positioning system location on the navigation radio display. Technician may find Diagnostic Trouble Codes B2462-02, B2462-04, B2470-02, B2470-04, B125C-01, B125C-02, or B125C-04. Technician should replace the high efficiency antenna with the latest part number in the catalog.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · STRUCTURE:FRAME AND MEMBERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the iPod that the first song will still be displayed when the next song in the list is playing. Engineering has deemed this to be a normal operating characteristic of the vehicle and no repair attempts should be made.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to download the USB software from TIS2WEB using the vehicle identification number every time a programming event of the human machine interface module is needed. Damage could be caused to the module if USB programmed with the incorrect software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of engine misfire/tick noise, Malfunction Indicator Lamp (MIL) On, and/or DTC P0300 set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0011. If the technician has followed all published Service Information diagnosis and has not come to a conclusion, technician should check the oil pressure at the oil pressure sender. Then the number two cam bearing should be inspected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a CD player is inoperative. Technician should cycle power to the CD play and retest. If the CD player starts working advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. If the CD player is still inoperative technician will need to test the power and ground circuits. If no concern with power, ground, or connections, replace the Disc Player.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the lower center section of the display will not work when pressed. Technician will need to replace the Integrated Center Stack for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that radio is inoperative, loss of sound, or their display is blank. Technician will need to cycle power to the radio and retest. If the radio starts working advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. If the radio is still inoperative technician will need to test the power, ground, and circuit 5060 circuits. If no concern with power, ground, circuit 5060 or connections, replace the radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about when listening to an iPod that the first song will still be displayed when the next song in the list is playing. If this concern is encountered, use the browse button on the radio display and navigate to the desired artist, album, song, or Genre. Once the desired selection is made, the correct information will be displayed on the radio screen.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that navigation system has inaccurate estimated time of arrival. This is a normal operating characteristic of the New Generation Infotainment system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information for a customer concern of a rattle noise on right front cross rail of the luggage carrier.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a CD player is inoperative. Technician should cycle power to the CD play and retest. If the CD player starts working advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. If the CD player is still inoperative technician will need to test the power and ground circuits. If no concern with power, ground, or connections, replace the Disc Player.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P16F3 as a current or history code in the Transmission Control Module. Technician will need to insure that the Diagnostic Trouble Code P16F3 is set in the Transmission Control Module. If the Diagnostic Trouble Code is set in the Transmission Control Module Technician will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an inoperative radio. Technician may find Diagnostic Trouble Code U0184 stored in multiple modules. If the concern is present at the dealership technician will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have rough, harsh, or stiff ride. The concern is most noticeable between 35-55 mph on fairly smooth roads, when coming in contact with small road imperfections, or expansion joints. Technician will need to use the vibration analyzer CH-51450-A (Pico Oscilloscope), while driving the vehicle in 35-55 mph range on the same section of road for each stage of evaluation. If a rough, harsh, stiff ride has been determined to be the customer?s concern following evaluation using the Pico scope, then replace the complete front suspension shock with coil spring assemblies, and rear shocks with updated parts and reprogram the Suspension Control Module (K19) with updated calibrations available in TIS2WEB.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for transmission control module reprogramming to correct a customer concern for MIL illuminated with firm shifts, shudder, engine RPM flare and DTCs P0606, P16F3 or P2818 set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CADILLAC/CHEVROLET: AFTER POSITIONING SHIFT LEVER INTO PARK, IT FAILS TO HOLD AND VEHICLE ROLLS WHEN BRAKE PEDAL IS RELEASED. MODEL 2013-15. ATS, CTS, ESCALADE, AVALANCHE, CAMARO, CORVETTE, EXPRESS, SILVERADO, SUBURBAN, TAHOE, SAVANA, SIERRA, YUKON. *PE UPDATED 2/5/16. *PE UPDATED 2/12/16. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to call General Motors Technical Assistance Center if the customer has a malfunction indicator lamp on and there is a diagnostic trouble code P16F3 set in the transmission control module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a water leak in in the second row seating area. Inspect the C-pillar area of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians with repair information to correct a customer concern of rough, uneven or irregular horizontal seam on liftgate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15216 - CUSTOMER SATISFACTION PROGRAM. CERTAIN 2015 MODEL YEAR CADILLAC ESCALADE AND ESCALADE ESV; CHEVROLET SILVERADO LD CREW AND DOUBLE CAB; AND GMC SIERRA LD CREW, SIERRA LD CREW DOUBLE CAB, YUKON, AND YUKON XL MODEL VEHICLES THAT ARE EQUIPPED WITH A 6.2L ENGINE (RPO L86) AND 8-SPEED AUTOMATIC TRANSMISSION (RPO M5U) MAY HAVE A CONDITION IN WHICH THE U-JOINT RETAINER BOLTS LOSE INDEX. IF THIS CONDITION OCCURS, THE CUSTOMER MAY HEAR OR FEEL A CLUNKING NOISE WHEN CHANGING SPEED. IF THIS CONDITION IS NOT CORRECTED, REDUCED CLAMP LOAD MAY CAUSE THE PROPSHAFT TO MOVE RELATIVE TO THE AXLE YOKE AND THE CUSTOMER MAY FEEL A VIBRATION. IF ONE OR MORE BOLTS BACK OUT COMPLETELY, THE PROPSHAFT MAY SEPARATE FROM THE AXLE RESULTING IN A LOSS OF DRIVE AND POTENTIAL DAMAGE TO THE UNDERSIDE OF THE VEHICLE. DEALERS ARE TO REPLACE TWO U-JOINT RETAINERS AND FOUR U-JOINT RETAINER BOLTS WITH NEW BOLTS THAT INCLUDE AN ADHESIVE PATCH.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of warm air exhausting from driver and/or passenger front seat back into 2nd row seating area causing occupant discomfort.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that there was a temporary change to the frame coating on some vehicles. These vehicles will be painted with environmental coating rather than the normal frame wax. The environmental coated frames meet or exceed General Motors specifications for corrosion and no repair should be made.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides diagnosis and repair information to correct a customer concern of alleged no park, vehicle rolls in park or park will not hold.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with erratic or hesitation when opening and closing the power lift gate. There may be a diagnostic trouble code B153A set in the power lift gate module. This concern could occur if the left lift gate actuator is internally coming apart. The actuator will need to be replaced however care must be taken when removing the actuator from the vehicle. If the internal portion of the actuator had completely separated the end of the actuator could become a projectile when removed. Obtain a number 8 self-tapping screw that measures 1 ½ inches long. Fully open the lift gate and install the screw anywhere in a 30 millimeter space from the bottom of the smooth tube to secure the tubes. Continue with the lift gate actuator by following the lift gat power assist actuator procedure in service information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a Service Engine Soon light with a Diagnostic Trouble code P0300 set. There may be a rough running engine associated with this concern. If service information diagnostics have been completed and there is still no trouble found, the technician is to inspect for a possible terminal tension concern on the ignition coil power feed for the cause of the rough running engine and or the P0300. For the Service Engine Soon light or traction control lamp concern check the X2 connector of the under hood fuse block for poor pin retention.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of steps to take if Pandora is inoperative or experiencing intermittent operation. 1. Verify Pandora is installed on the device. 2. Make sure the device is Bluetooth connected and paired to Cadillac CUE. 3. Make sure stations have been created in Pandora on the device. 4. Launch Pandora by selecting the Pandora Icon on the Integrated Center Stack and allow a few moments for the App to start on the device. 5. Make sure the Bluetooth volume on the device is turned up or on. Pandora volume is controlled by the device since it is a Bluetooth application. 6. Pandora is controlled by the devices connection and data signal. If the device has a poor data signal Pandora may not play. 7. If Pandora is successfully working, the device should display "Accessory". 8. Apple devices must be connected via USB to the vehicle to launch Pandora. Customers can use the "Bluetooth" input under the media selection to stream audio but will not have full control of the device using the radio. 9. Some Android phones require a setting in Pandora to allow Pandora to access automotive audio. Launch Pandora on the phone, in Pandora select settings in the upper right hand corner of the screen, select "advanced" and make sure "Bluetooth for Automotive" is checked and enabled. 10. If all of the above tips have been verified, and the message "No Internet Connection" is displayed on the Integrated Center Stack screen, CUE is not picking up the devices internet connection. Ensure that the device has adequate battery life and a good data signal. Check to see if Pandora can be heard through the device itself. If Pandora is playing through the handset device, try repairing the device and/or switching to a different audio screen and coming back to Pandora. 11. If Pandora is installed on a phone and a media device is also connected, such as an IPod that is hardwired to the vehicle, there may be confusion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin communicates part restriction and ordering process information for OnStar®Vehicle Communication Interface Modules (VCIM) (GMNA Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
15389 - SERVICE UPDATE. THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO REPROGRAM THE TRANSMISSION CONTROL MODULE (TCM) ON CERTAIN 2015 MODEL YEAR CADILLAC ESCALADE, ESCALADE ESV, CHEVROLET SILVERADO, GMC SIERRA, YUKON DENALI AND YUKON DENALI XL VEHICLES EQUIPPED WITH AN 8L90 8-SPEED (M5U) TRANSMISSION AND 6.2L (L86) ENGINE. THESE VEHICLES MAY HAVE A CONDITION IN WHICH TRANSMISSION CALIBRATION ALLOWS A HIGHER THAN TARGET ENERGY INPUT TO THE TORQUE CONVERTER CLUTCH (TCC) UNDER CERTAIN CONDITIONS. THIS MAY LEAD TO FASTER THAN EXPECTED TORQUE CONVERTER CLUTCH MATERIAL WEAR, AND A SHUDDER FEELING WHEN THE TCC IS APPLIED.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a content theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". This is a list of triggers that can cause a content theft alarm sounding. Driver door Passenger door, Left rear door, Right rear door, Rear closure, Tonneau Cover, Hood, Ignition Voltage, Intrusion, Inclination, Telematics enhanced service alarm, Battery reconnect detected, Unauthorized Pulse Width Modulated change, Security Indicates Tamper, and Glass Breakage. If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with the driver?s door lock cylinder cover missing. The cover may have been removed to access the key cylinder while shipping in transport mode. If the cover is missing inspect the inside of the vehicle to see if the cover was placed inside during shipping. If the cover is missing a replacement can be ordered through the parts department using part number 13596115. A change has been made on the 2015 model with regular production option code AVF to allow the remote keyless entry to work when in transportation mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician when the customer complaint on a noise from the transmission when the engine starts. The noise may be a clunk with a bump sensation. This condition may be caused by turning the engine off and then quickly restarting it. The transmission control module doesn?t have adequate time to power down and the 1-2-7-8-R along with the 1-2-3-4-5-R clutches will apply at maximum line pressure causing this concern. This is considered normal operation if the transmission control module is not allowed to power down before restarting the engine. The transmission control module needs the transmission to be placed in park the ignition turned off and the door opened and closed. After closing the door the transmission control module requires 2 minutes before the engine should be restarted. If the concern is present and duplicated after following the power down procedure the General Motors Technical Assistance Center for further direction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to tell vehicles built with text messaging and vehicles that are not. The text messaging feature was not available at the start of production on the sport utility vehicle or heavy duty truck. The option was added mid-cycle production. These utility and heavy duty pickup models must have regular production option code AVF to have the text messaging feature. There is no upgrade available to add text messaging to a vehicle that was built without it.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to check for an engine build code of K and the dates between 15005 and 15117, the customer concern is an engine oil leak at the oil filter location of the oil pan. A loose oil filter adapter is found to be the cause of the concern, tighten it to 55 newton meters or 40 foot pounds. It is also advised to clean any residual oil from the oil pan area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that some vehicles the haptic seat motors can be felt in the seat. Technician will access both haptic seat motors and rotate the motors flat, and then reinstall them back into the seat cushion. This will help improve the comfort of the seat cushion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for vehicles that exhibit a driver?s power memory seat and power adjustable pedals inoperative. Look for poor terminal tension at the left instrument panel fuse block connector X1 terminals 27 and 28. If poor retention is found in these terminals replace them with terminated lead part number 19301761.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of MIL illuminated with Engine Power is Reduced message displayed after cold start. Technician may find DTC P16F3 set in history.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information to correct a customer concern of a metallic slap or ping noise when the engine is running, in Park or Neutral gear, or if accelerator pedal is snapped quickly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a concern on vehicles where the power lift gate binds or makes a popping noise when operated the gate also may not stay open. In most cases no diagnostic trouble codes will be set. The concern is most likely caused by the passenger side strut binding between the inner and outer tubes. Replace the passenger side strut and only if the concern is still present replace the driver side actuator.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a blank radio display. Technician may find a Diagnostic Trouble Code U150F stored in the Radio / Heater-Vent-Air Conditioning controls. Technician will verify if the correct display is installed. If the Diagnostic Trouble Code is current inspect the circuit form end to end.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a reduced power message, steering assist, engine stall or the instrument panel, radio, and or Heater-Vent-Air Conditioning go blank with multiple diagnostic trouble codes. If any of the following diagnostic trouble codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, U1510, U0073, B127B, B2605, B3600,C0800, U0428, and U0452 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. The concern may be most noticeable while the engine is operating in 4-cylinder Active Fuel Management mode in the 1,100-1,400 RPM range. If the noise is excessive it may excite the roof sheet metal and compound the issue, if this concern is found refer to the latest version of PIT5318. If the concern is qualified to be present during V4 mode operation, but is deemed to be normal by comparing to a like vehicle, then no further repairs should be made, as this is a normal characteristic. If the concern is qualified to be present during V4 mode operation, but is deemed excessive by comparing to a like vehicle then continue with the direction in the Preliminary Information. Vehicles equipped with the 6.2 liter engine and noise cancellation, the noise cancellation may not be working or working incorrectly this can be the cause of the issue. Technician should inspect for aftermarket audio components, objects blocking the microphones or speakers, Diagnostic Trouble Codes B0560, B1277, B127C, or B127D. By the technician pulling the fuse for the amplifier the noise cancellation will be disabled if the noise improves there may be an issue with the noise cancellation system. Technician should inspect the exhaust system also. Exhaust should be checked when it is hot and cold while the vehicle is in neutral, forward and reverse gear. Inspect the exhaust system for loose and/or missing fasteners, heat shields damaged, joints and/or couplings not properly seated, bracket and/or insulator mounting concerns, inadequate clearance to body and/or chassis components, improper alignment, disconnected and/or missing insulators, cracked, dry-rotted, and/or oil-soaked insulators, stretched, twisted, broken, torn, and/or collapsed insulators, and bent, twist
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for vehicles with the radio inoperative. The technician may find no communication with the radio and a diagnostic trouble code U0184 set in other modules. Technician is to call General Motors Technical Assistance Center for direction before attempting to diagnose or repair this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a vehicle setting both a P2635 and P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range. Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2. Navigate to fuel system depressurize and at engine idle depressurize the fuel system. The fuel pressure sensor value should drop to 0 and the engine will stall. If a sensor is causing this concern the suspected sensor will not drop to 0 the engine will stall however the sensor will still read 30 to 40 pounds per square inch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of wind noise generating from accessory roof cross rails.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15178A - SERVICE UPDATE (REVISED PARTS INFORMATION, SERVICE PROCEDURE AND WARRANTY TRANSACTION INFORMATION). THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO PERFORM A DRIVE AUDIT AND, IF NECESSARY, REPLACE THE REACTION/OUTPUT CARRIER ASSEMBLY AND ASSOCIATED PARTS ON CERTAIN 2015 MODEL YEAR CADILLAC ESCALADE, ESCALADE ESV; CHEVROLET SILVERADO LD CREW, SILVERADO LD CREW LTZ, SILVERADO LD EXT LTZ; AND GMC SIERRA LD CREW, SIERRA LD CREW DENALI, SIERRA LD EXT, YUKON, YUKON DENALI, YUKON XL, YUKON XL DENALI VEHICLES EQUIPPED WITH AN 8-SPEED TRANSMISSION (M5U) AND A 6.2L ENGINE (L86). SOME OF THESE VEHICLES MAY EXHIBIT A TRANSMISSION GEAR WHINE NOISE AT 1000-2000 RPM AND BETWEEN 20 MPH (32 KPH) AND 35 MPH (56 KPH).
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/CADILLAC/GMC: INSTRUCTION INFORMATION REGARDING AN OIL LEAKAGE FROM ENGINE, AROUND LOCATION OF OIL FILTER OF OIL PAN. MODEL 2015 ESCALADE, SIERRA/SILVERADO 1500, SUBURBAN, YUKON, YUKON XL, TAHOE. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/CADILLAC/GMC: TSB CONTAINS AN OWNER'S NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. THE U JOINT RETAINER BOLTS, ON CERTAIN TRUCKS/VANS, HAVE A LOSE INDEX AND CLUNKING NOISE IS HEARD OR FELT WHEN SPEED CHANGES AND IF NOT CORRECTED, PROPSHAFT WILL MOVE TOWARDS AXLE YOKE. MODEL 2015 ESCALADE, ESCALADE ESV, SIERRA LD CREW & DOUBLE CAB, YUKON, YUKON XL, SILVERADO LD CREW & DOUBLE CAB. *PE
Source components: POWER TRAIN:DRIVELINE:UNIVERSAL JOINT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 8L90 8 Speed Automatic Transmission is on exchange through General Motors Product Quality Center. Dealer will need to contact the General Motors Product Quality Center for further assistance.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have various Heater-Vent-Air Conditioning issues. Technician should use Tis2Web to reprogram the Heater-Vent-Air Conditioning control module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center when operated below 10 degrees Fahrenheit (-12 Celsius). Technician may find C0398 or C0326 stored in the Transfer Case Control Module. For vehicles with Regular Production Option Code NQH and NQ6 and only setting Diagnostic Trouble Codes C0398 or C0398 and C0326 the replacement of the actuator motor will correct the concern. Dealer will need to contact General Motors Product Quality Center for further assistance. For vehicles with Regular Production Option Code NQH and NQ6 with other transfer case Diagnostic Trouble Codes. If the vehicle had a Diagnostic Trouble Code C0398 in the transfer case control module stored with any other codes such as C0392, C0396, C0306 or other codes related to rotational position sensor or actuator position sensor it is likely that is causing a C0398 to set and replacement of the actuator will likely not repair the vehicle. For vehicles with Regular Production Option Code NP0 and only have a Diagnostic Trouble Code C0398 stored in the transfer case control module, the technician should insure the transfer case control module calibrations are up-to-date in Tis2Web.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an oily substance is found on the inside windshield surface and appears to be leaking from the rear view mirror area. Technician should inspect the moisture sensor for being the source of the leak, if found to be leaking, carefully remove the moisture sensor. Clean the glass surface and sensor bracket with an isopropanol alcohol wipe until the surfaces are clean, then re-install the moisture sensor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair procedure information to correct a customer concern of Transport Mode On message displayed in Driver Information Center (DIC) and/or battery light is flashing.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides radio programming information to correct customer concerns about no XM audio or time shift, radio lock-up, slow response, vertical line between clock and temperature, poor FM reception (Truck Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to access XM Weather. If the system responds by highlighting the XM Weather Icon but it does not enter the application technician should replace the Human Machine Interface module for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"15178 - SERVICE UPDATE. THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO PERFORM A DRIVE AUDIT AND, IF NECESSARY, REPLACE THE REACTION/OUTPUT CARRIER ASSEMBLY AND ASSOCIATED PARTS ON CERTAIN 2015 MODEL YEAR CADILLAC ESCALADE, ESCALADE ESV; CHEVROLET SILVERADO LD CREW, SILVERADO LD CREW LTZ, SILVERADO LD EXT LTZ; AND GMC SIERRA LD CREW, SIERRA LD CREW DENALI, SIERRA LD EXT, YUKON, YUKON DENALI, YUKON XL, YUKON XL DENALI VEHICLES EQUIPPED WITH AN 8-SPEED TRANSMISSION (M5U) AND A 6.2L ENGINE (L86). SOME OF THESE VEHICLES MAY EXHIBIT A TRANSMISSION GEAR WHINE NOISE AT 1000-2000 RPM AND BETWEEN 20 MPH (32 KPH) AND 35 MPH (56 KPH)."
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles with visible water leak or signs of water intrusion from the antenna base, red OnStar LED, unable to connect to OnStar, OnStar unable to locate the vehicle, OnStar has inaccurate global positioning system location, no global positioning system on the navigation radio display, and inaccurate global positioning system location on the navigation radio display. Technician may find Diagnostic Trouble Codes B2462-02, B2462-04, B2470-02, B2470-04, B125C-01, B125C-02, or B125C-04. Technician should replace the high efficiency antenna with the latest part number in the catalog.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides inspection and repair information to correct a customer concern of XM/Cellular Mobile Phone/OnStar Antenna looseness or damage, XM/Cellular/OnStar reception performance degraded, rattle/flutter/squeak noise, wind noise/whistle at highway speeds, water leak on headliner at sunvisor.