Original record summaries, dates and identifiers for this model-year. Records 1,201–1,300 of 2,405, ordered newest first. Dated records on this page: Aug 23, 2016–Nov 30, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Nov 30, 2016Service Bulletin/Repair Instructions
PIP5446
NHTSA communication ID: 10114851
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
Source components: ELECTRICAL SYSTEM · ELECTRONIC STABILITY CONTROL (ESC) · STEERING · TIRES · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin is ending the need for information on vehicles with the condition of Vehicle Crank with No Start or Stalling with DTC P0011 and/or P00C6 Set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to repair information to correct a customer concern of the hood fluttering, vibrating or displaying visible motion at highway speeds or over rough road surfaces.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have multiple messages on the driver information center Service Parking Assist System, Service Adaptive Cruise Control, and Service Surround Vision Camera. The Front park, turn signal, day time running lights, and/or cornering lights may be inoperative. Some fuses may be blown F10DL, F19DR, F43UA, and/or F46DR. Also these diagnostic trouble codes may be set U0075, U209E, U026A, U026B, U026C, U0265, U0268, and/or U0269. These concerns could be caused by the fascia harness shorted at the end of the right front bumper bar. The front fascia may need to be removed to make repairs to the wiring harness if any damage is found. Also relocate the harness to prevent the concern in the future.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:BUMPERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · LANE DEPARTURE: ASSIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.
Source components: POWER TRAIN · SERVICE BRAKES · VEHICLE SPEED CONTROL:LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to eliminate coolant smell and/or a slight leak at the radiator.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have harsh concerns. Technician are advised to use GDS2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical Bulletin provides a fix to reprogram the radio for vehicles that may experience any of the following conditions: DTC U0184 Set, Radio Inoperative, Blue Screen, AM Clipping Noise, HD On/Off Status Not Retained in Stations, Time Lag on Transitions, No Audio with Internal Amp, Park Assist Symbol Position Wrong in Rear View Camera
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have harsh shifts concerns. Technicians will use Global Diagnostic System 2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found in the pan, technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track l
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a rattle noise from the second row seat. Technician will need to inspect the striker not aligned properly in latch opening. To repair this condition, rework/adjust the striker in the direction to center it in the latch opening. An adjustable wide mouth metal working tool may be used to adjust the striker just enough to center in the latch opening. Technician may find a seat bottom latch may have an unequal latch opening side-to-side for the striker to seat into. To repair this condition, with the affected seat in the tumbled forward position, while applying steady, firm pressure, cycle the seat down into the latched position. Some vehicles built prior to 09/21/2015 with 60/40 Split Bench Seat may have 60-percent long side bench, inboard latch may not be properly aligned in striker opening. Technician will need to place a 2.6 mm thick flat washer over the 40 percent seat base stud, not the floor stud. Some vehicles may have a seat base plat that rattles against the rib in the floor pan. Apply Mylar tape to the floor pan under the seat plate to provide relief for the rattle condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with various Heater-Vent-Air Conditioning blower mode or temperature issues. Technician will need to reprogram the Heater-Vent-Air Conditioning control module using Tis2Web and Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 mph steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will drive the vehicle and monitor the torque converter clutch slip. The torque converter clutch slip speed should be 10 rpm or less also note if the shudder takes place during torque converter clutch apply. If the torque converter clutch slip speed is in the range of 10 RPM or less the condition is possibly related to engine performance. If the shudder is only present in 4 cylinder mode and torque converter clutch slip is 10 rpm or less deem the shudder concern normal characteristic of Active Fuel Management. If the slip speed is beyond 10 rpm or there is shudder during torque converter clutch apply the torque converter will need to be replaced. Also flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a radio screen appears bubbled or is delaminating. Dealer can replace model years 2013 and 2015. If working on a 2016 model year vehicle dealer will need to contact General Motors Technical Assistance Center for further assistance. Technician should replace the Integrated Center Stack with the latest part number out of the parts catalog.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
Source components: BACK OVER PREVENTION · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have "Service Theft System" message on the Driver Information Center. Technician may find Diagnostic Trouble Code B291B sym 3B and is unable to clear the Diagnostic Trouble Code. Technician will need to restore communication between the Body Control Module and Theft Deterrent Sensor Module to clear the Diagnostic Trouble Code.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
Source components: ELECTRONIC STABILITY CONTROL (ESC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin aids the technician on diagnosing possible vibrations in a vehicle, methods used for testing each scenario and documenting findings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition.
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine, transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Thins engineering informational bulletin is requesting information from the field on vehicles that have the condition of rear auxiliary a/c not cooling or blowing warm air.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON THE TIRES SUPPLIED WITH A NEW VEHICLE ARE COVERED BY GENERAL MOTORS AGAINST DEFECTS IN MATERIAL OR WORKMANSHIP UNDER THE BUMPER-TO-BUMPER NEW VEHICLE LIMITED WARRANTY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P2635, U0074 AND OR U18A2. TECHNICIAN WILL NEED TO FOLLOW PUBLISHED DIAGNOSTICS FOR DIAGNOSTIC TROUBLE CODES U0074 WOULD TAKE PRIORITY OVER U18A2 IF BOTH SET BEFORE ADDRESSING DTC P2635.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS TO RESOLVE THE ISSUE OF AN OILY SUBSTANCE THAT MAY BE FOUND ON THE INSIDE WINDSHIELD SURFACE, AND APPEARS TO BE LEAKING FROM THE REAR VIEW MIRROR AREA. TECHNICIAN WILL REMOVE THE MOISTURE SENSOR AND CLEAN THE GLASS AND MOUNTING BRACKET WITH ALCOHOL WIPE. IF THE GEL SEPARATES FROM THE SENSOR THE SENSOR WILL NEED TO BE REPLACED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR VEHICLES WITH A ROUGH IDLE AND/OR VIBRATION AT IDLE IN DRIVE. THIS CONDITION WILL NOT BE PRESENT IN PARK, OR NEUTRAL. THIS CONCERN MAY BE CAUSED BY GROUND OUT WITHIN THE ONE OR BOTH ENGINE MOUNTS. TECHNICIAN WILL USE CH-51450-A (PICO OSCILLOSCOPE) TO MEASURE THE VIBRATION DISTURBANCE. IF THE VIBRATION CONCERN IS E1.5 IN THE HORIZONTAL / LATERAL DIRECTION WITH PICO SENSOR MOUNTED IN SEAT TRACK AS INDICATED CONTINUE WITH STEPS TO REDUCE THE AMPLITUDE OF THE VIBRATION BY ADDING SPACERS IN KEY LOCATIONS TO REDUCE GROUND OUT WITHIN THE ENGINE MOUNTS. THE 6.2L ENGINE HAS A CHARACTERISTIC E1 WHICH CAN BE FELT, AND MAY BE DESCRIBED AS A LOPEY IDLE. DO NOT CONFUSE 6.2L E1 CHARACTERISTIC (NOT CAUSED BY MOUNT GROUND-OUT), WITH E1.5 NORMAL IDLE CHARACTERISTICS BEING TRANSMITTED INTO THE TRUCK VIA GROUND-OUT THRU THE ENGINE MOUNTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP ON AND DIAGNOSTIC TROUBLE CODE P0300 - P0308 MAY SET. TECHNICIAN WILL INSPECT FOR LOSE SPARKPLUG WIRE. IF A SPARK PLUG WIRE IS FOUND LOSE CHECK FOR A MISSING C CLIP ON THE WIRE END FOR THE IGNITION COIL. IF THE CLIP IS MISSING REPLACE THE WIRE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS ON DIAGNOSING AND REPAIRING VEHICLES THAT MAY HAVE UNWANTED GRADE BRAKING, REDUCED ENGINE POWER WITH NO DRIVER INFORMATION CENTER MESSAGES BRAKE PEDAL OVERRIDE FEATURE , TRANSMISSION BUSY OR FREQUENT SHIFTING UP OR DOWN, AND DIAGNOSTIC TROUBLE CODES P057B, P057C, AND/OR P057D MAY OR MAY NOT BE SET. TECHNICIAN WILL USE THIS PRELIMINARY INFORMATION TO FIND THE BRAKE PEDAL POSITION DATA PARAMETERS IN THE SCAN TOOL, AND ALSO TO PROVIDE SOME ADDITIONAL DIAGNOSTIC HELP. THESE ISSUES MAY BE CAUSED BY AN INCORRECT BRAKE PEDAL POSITION SENSOR INPUT TO THE ENGINE CONTROL MODULE. TECHNICIAN WILL VERIFY WITH THE SCAN TOOL IF THE ENGINE CONTROL MODULE HAS THE CORRECT PARAMETERS FOR THE BRAKE PEDAL POSITION SENSOR. IF AN ENGINE CONTROL MODULE BRAKE PEDAL POSITION SENSOR RELEARN IS PERFORMED, THE TRUCK MAY BE TEMPORARILY REPAIRED UNTIL THE INTERMITTENT WIRING ISSUE BETWEEN THE ENGINE CONTROL MODULE AND BRAKE PEDAL POSITION SENSOR OCCURS AGAIN. ON 2014 AND NEWER TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X115 AND X119. ON THE 2014 AND PREVIOUS TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X205.
Source components: ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL · ENGINE · PARKING BRAKE · POWER TRAIN:AUTOMATIC TRANSMISSION · SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE THE LOWER CENTER SECTION OF THE DISPLAY WILL NOT WORK WHEN PRESSED. TECHNICIAN WILL NEED TO REPLACE THE INTEGRATED CENTER STACK FOR THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the Homelink transmitter to correct the customers concern of the garage door wont open from far distances.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT THE RADIO WILL NOT SAVE XM FAVORITES. TECHNICIAN WILL NEED TO REPLACE THE RADIO TO ADDRESS THE CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" MESSAGE ON THE DIC WHEN ATTEMPTING TO ACTIVATE THE CRUISE. TECHNICIAN SHOULD CONSIDER ENVIRONMENTAL FACTORS, REPAIR, COLLISION, AFTERMARKET PARTS, AND RADAR ALIGNMENT FACTORS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE THE ONSTAR WIRELESS FIDELITY INOPERATIVE. TECHNICIAN WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER WITH A SCAN TOOL CONNECT TO THE VEHICLE FOR FURTHER ASSISTANCE.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is ending the need of information from the field on vehicles with the condition of a rattle noise from the second row seat.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT CUSTOMERS THAT MAY REQUEST THE FACTORY INTEGRATED TRAILER BRAKE CONTROLLER REGULAR PRODUCTION OPTION CODE (JL1) BE INSTALLED ON THEIR FULL-SIZE PICKUP OR SUV WHEN THE VEHICLE WAS NOT ORDERED WITH THE OPTION. DEALER SHOULD ADVISE THE CUSTOMER IT CANNOT BE ADDED TO THE VEHICLE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS DIAGNOSTIC TOOL KIT (EL-51578) HAS BEEN RELEASED TO HELP DIAGNOSE ANY OF THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS CONCERNS. THE KIT CONTAINS HEADER CONNECTORS THAT ARE INSTALLED TO BYPASS MEDIA ORIENTED SYSTEMS TRANSPORT BUS MODULES. THE BYPASS CONNECTOR ALSO CONTAINS A TERMINAL FOR VERIFYING MEDIA ORIENTED SYSTEMS TRANSPORT CONTROL CIRCUIT VOLTAGES. TECHNICIAN SHOULD REVIEW MEDIA ORIENTED SYSTEMS TRANSPORT BUS DESCRIPTION AND OPERATION AND DIAGNOSTIC TROUBLE CODE U0028 DIAGNOSTIC PROCEDURES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the radio to correct a customer concern of radio Inoperative, blue Screen, AM clipping noise, HD on/off status not retained in stations, time lag on transitions, no audio with internal amp, park assist symbol position wrong in rear view camera.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE SPEEDOMETER INACCURATE READS 5 MPH WHEN TRAVELING 50 MPH. ENGINEERING IS WORKING TO DEVELOP A SOLUTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT GENERATION 5 ENGINES WITH REGULAR PRODUCTION OPTION CODE L83, L86, OR LV3 MAY HAVE AN OIL CONSUMPTION CONCERN WERE ONE QUART IN 2000 MILES IS BEING USED. DEALER WILL CONFIRM OIL LEVEL WAS PROPERLY CHECKED PER OWNERS MANUAL, AND CHECK THE BOLT TORQUE ON THE VALVE LIFTER OIL MANIFOLD ASSEMBLY, BEFORE YOU CONTACTING GENERAL MOTORS PRODUCT QUALITY CENTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE HESITATION OR A STALLING CONDITION WHILE IN AMBIENT TEMPERATURES 100 DEGREES OR HIGHER. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P2635 AND OR P018B SET. THE DEALER IS ADVISED TO REPLACE THE IN TANK FUEL PUMP MODULE ASSEMBLY TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION HAS THE STEPS ON DIAGNOSING THE CONCERN OF EXCESSIVE OIL CONSUMPTION FOR THE GENERATION 5 ENGINE AND TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE. CUSTOMER'S ENGINE IS USING EXCESSIVE OIL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT WHEN PROGRAMING THE IMMOBILIZER THEFT LEARN IT MAY NOT COMPLETE AND/OR SHOW "CONTROLLER ID NOT SUPPORTED" AFTER THE FIRST FEW MINUTES INTO THE LEARN EVENT. TECHNICIAN WILL NEED TO REMOVE POWER FROM THE ONSTAR MODULE BEFORE PERFORMING A IMMOBILIZER THEFT LEARN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN OF ADDITION INFORMATION WHEN DIAGNOSING A SERVICE DRIVER ASSIST MESSAGE WITH A DIAGNOSTIC TROUBLE CODE B172E AND OR A B172F. THE HAPTIC SEAT MOTOR HAS A PIGTAIL LEAD COMING OFF OF IT. IN MANY CASES THE WIRING PIGTAIL NEAR THE HAPTIC SEAT MOTOR HAS BROKEN AND WILL REQUIRE REPLACEMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A SERVICE 4WD MESSAGE DISPLAYED IN THE DRIVER INFORMATION CENTER. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES C0392 OR C0396. TECHNICIAN SHOULD CHECK THE TERMINAL TENSION ON THE TRANSFER CASE CONTROL MODULE X1 CONNECTOR. TECHNICIAN SHOULD REPAIR ANY TERMINAL THAT HAVE POOR TERMINAL TENSION.
Source components: POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE HESITATION OR A STALLING CONDITION WHILE IN AMBIENT TEMPERATURES 100 DEGREES OR HIGHER. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P2635 AND OR P018B SET. DEALER SHOULD COMMUNICATE TO THE CUSTOMER THAT WE APOLOGIZE FOR THIS INCONVENIENCE AND THAT GENERAL MOTORS IS WORKING ON A SOLUTION FOR THIS CONCERN. IF WORKING ON POLICE PURSUIT VEHICLES REGULAR PRODUCTION OPTION CODE PPV OR FLEET VEHICLES REGULAR PRODUCTION OPTION CODE FLT, CONTACT THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THE FLOOR CENTER CONSOLE SLIDING COMPARTMENT DOOR IS BROKEN. UPON INSPECTION IT MAY BE FOUND THAT THE DOOR WILL NOT LATCH OPEN, OR MAY BE LOCKED IN THE CLOSED POSITION. TECHNICIAN WILL NEED TO REPLACE THE COMPARTMENT SLIDING DOOR LATCH, GENERAL MOTORS PART NUMBER 23417257. DEALER SHOULD ADVISE THE CUSTOMER ON PROPER PUSH-PUSH OPERATION FOR THE SLIDING DOOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A REAR HVAC AND/OR REAR HEATED SEATS WILL CHANGE SETTINGS, OR THAT THE REAR HVAC CONTROLS ARE TOO SENSITIVE. TECHNICIAN WILL NEED TO REPLACE THE REAR HEATER-VENT-AIR CONDITIONING CONTROL WITH UPDATED PART NUMBER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP, ANTILOCK BRAKING SYSTEM MALFUNCTION INDICATOR LAMP, SERVICE SUSPENSION SYSTEM MESSAGE, MISFIRE, HESITATION, NO CRANK, HEATER-VENT-AIR CONDITIONING INOPERATIVE. TECHNICIAN MAY FIND F11UA, F104UA, F35UA, AND OR F60UA BLOWN. TECHNICIAN SHOULD INSPECT THE ENGINE HARNESS NEAR THE VACUUM PUMP PULLEY TO BE CHAFING. TECHNICIAN WILL NEED TO REROUTE THE WIRE HARNESS AND REPAIR AND DAMAGED WIRES.
Source components: ELECTRICAL SYSTEM · ENGINE · SUSPENSION.