Original record summaries, dates and identifiers for this model-year. Records 1,601–1,700 of 2,405, ordered newest first. Dated records on this page: Jul 10, 2015–Oct 13, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 13, 2015Service Bulletin/Repair Instructions
PIP5337
NHTSA communication ID: 10114891
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 mph steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will drive the vehicle and monitor the torque converter clutch slip. The torque converter clutch slip speed should be 10 rpm or less also note if the shudder takes place during torque converter clutch apply. If the torque converter clutch slip speed is in the range of 10 RPM or less the condition is possibly related to engine performance. If the shudder is only present in 4 cylinder mode and torque converter clutch slip is 10 rpm or less deem the shudder concern normal characteristic of Active Fuel Management. If the slip speed is beyond 10 rpm or there is shudder during torque converter clutch apply the torque converter will need to be replaced with a updated part number.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.25mm the crankshaft balancer will need to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are equipped with Hands Free Power Lift-gate Regular Production Option Code (TC2). Some customers may experience problems with the activation of the lift-gate hands free operation. Dealer will communicate to the customer some tips on the Hands free Lift-gate. The remote keyless entry FOB must be within 3 feet or 1 meter from the bumper. The foot kick is conducted at the direct center of the length of kick zone.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
Source components: ENGINE · POWER TRAIN · SERVICE BRAKES, HYDRAULIC:POWER ASSIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an inoperative radio. Technician may find Diagnostic Trouble Code U0184 stored in multiple modules. If the concern is present at the dealership technician will need to contact General Motors Technical Assistance Center for further assistance if within 4 hours from Warren, Michigan. Technician should remove power from the radio. If the radio starts working with a power cycle advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. After the power cycle and the radio is still inoperative record the radio power and ground readings and the voltage on the low speed data line.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the lift-gate actuator or strut that is going to be removed or replaced. If the actuator or strut comes loose off a ball stud after it has been reinstalled. Technician will need to replace the ball stud or ball stud w/bracket, the actuator or strut, and ensure the ball socket clips are properly orientated and seated to prevent it from reoccurring.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of a Service Stabilitrak message displayed on the Driver Information Center (DIC). During diagnosis, a technician may find DTC C0196-5A set in the Electronic Brake Control Module (EBCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with tips on the Text Messaging feature that is available on some newer General Motors infotainment systems.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to access XM Weather. If the system responds by highlighting the XM Weather Icon but it does not enter the application technician should replace the Human Machine Interface module for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have various Heater-Vent-Air Conditioning issues. Technician should use Tis2Web to reprogram the Heater-Vent-Air Conditioning control module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show ?No Audio? in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the disc will not eject, unwanted eject, or will not accept a disc. Technician should replace the Instrument Panel Multifunction Switch with the update part number for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a poor image quality from the surround vision camera. Technician will need to replace all four cameras and update the Video Processing Control Module (K157) with the latest calibrations available in TIS2WEB.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center when operated below 10 degrees Fahrenheit (-12 Celsius). Technician may find C0398 or C0326 stored in the Transfer Case Control Module. For vehicles with Regular Production Option Code NPO, NQH and NQ6 and only setting Diagnostic Trouble Codes C0398 or C0398 and C0326 reprogram the transfer case control module with the latest calibration from TIS2WEB and perform the setup procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have Malfunction Indicator Lamp. Technician may find a Diagnostic Trouble Code P16F3 current or history in the Transmission Control Module. Technician should verify that the Diagnostic Trouble Code P16F3 is set in the Transmission Control Module. If the Diagnostic Trouble Code is set in the Transmission Control Module technician will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a water leak and/or hiss type wind noise from the sunroof or headliner area. Technician should replace the sunroof seal to repair the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
Source components: LANE DEPARTURE: ASSIST · LANE DEPARTURE: WARNING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with misfires or roughness on cold start up. Technician may find a Diagnostic Trouble Code P0300 stored. Technician will add coolant dye to the system, run engine through warm up, pressurize the cooling system on a cold soak engine and inspect the suspect cylinder with a bore scope for coolant dye evidence. If coolant is found in the cylinder do not replace the cylinder head because that will not repair this concern. Dealer will need to contact General Motors Product Quality Center for engine replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15472 - SERVICE UPDATE. THIS BULLETIN PROVIDES A SERVICE PROCEDURE FOR CERTAIN 2015 MODEL YEAR CADILLAC ESCALADE AND ESCALADE ESV VEHICLES. THE PROCEDURE INVOLVES: (I) UPDATING THE VIDEO-PROCESSING MODULE (VPM) AND HUMAN-MACHINE INTERFACE (HMI) SOFTWARE, WHICH WILL IMPROVE THE 360-DEGREE CAMERAS CLARITY; (II) INSPECTING THE BATTERY FOR A LOW CHARGE CONDITION AND REPLACING THE BATTERY AS REQUIRED; AND (III) INSPECTING THE STEERING COLUMN FOR A CLICKING SOUND AND REPAIRING THE COLUMN AS REQUIRED.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ELECTRICAL SYSTEM:SOFTWARE · STEERING:COLUMN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: PARTS FOR MOST VEHICLES, CLUTCH, MASTER CYLINDER ASSEMBLY ARE, REQUIRED AND REQUESTED, TO BE RETURNED AND NEED TO REORDER REPLACEMENT PARTS USING SAME PART NUMBERS. *PE
Source components: POWER TRAIN:CLUTCH ASSEMBLY · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15667 - SERVICE UPDATE. THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO CHECK AND ADJUST TRANSMISSION FLUID LEVELS ON THE VEHICLES LISTED ABOVE. THESE VEHICLES MAY EXPEL EXTRA TRANSMISSION FLUID OUT OF A VENT FITTING AND HOSE ON THE TOP OF THE TRANSMISSION.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a repeat harsh shift, slip or flare concern after performing the service fast learn and the drive learn procedures were performed. Technician should insure the Transmission Control Module calibrations are up to date using Tis2Web. Also confirm the transmission service, fast learn and drive learn procedures listed in the latest version of bulletin 14-07-30-001 were performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that will the radio display stay on when accessing the Integrated Center Stack compartment door. This is a normal operating characteristic of this model year vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician about the 8L90 8 Speed Automatic Transmission is on restriction through General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician vehicles that have a wind noise from a side door, tick or rattle noise from a side door, B and/or C pillar area, or door applique trim has come loose. Technician should replace the door applique trim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician before replacing the crankshaft to review the following. Dealer should complete the Service Information diagnostics and the Cost Comparison Worksheet for Assembly Repair vs. Replacement. Technician will use the latest version of 09-06-04-026G to verify the Engine Control Module calibration is not an aftermarket calibration. If the customer prefers to keep the original numbers matching engine please call General Motors Technical Assistance Center for repair direction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
15155 - CUSTOMER SATISFACTION PROGRAM. CERTAIN 2015 MODEL YEAR CADILLAC ESCALADE, CADILLAC ESCALADE ESV, CHEVROLET SILVERADO CREW CAB, CHEVROLET SUBURBAN, CHEVROLET TAHOE, GMC SIERRA CREW CAB, GMC YUKON, AND GMC YUKON XL VEHICLES MAY HAVE A CONDITION THAT CAN ALLOW WATER TO LEAK INTO THE VEHICLES ROOF-MOUNTED ANTENNA. THIS CONDITION COULD PREVENT THE VEHICLES ONSTAR SYSTEM FROM ACCURATELY DETERMINING THE VEHICLES LOCATION; DISABLE THE VEHICLES COMPASS, NAVIGATION, AND XM RADIO SYSTEMS; ILLUMINATE THE VEHICLES RED ONSTAR LED INDICATOR; AND ALLOW WATER INTO THE INTERIOR PASSENGER COMPARTMENT. DEALERS ARE TO REPLACE THE ONSTAR® ANTENNA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Codes P0089, P127C, P127D, P0192, P0193, P228C, P228D, and P006C. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Codes that are stored. If Service Information does not lead to a repair for the concern, the fuel rail pressure sensor should be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC: CERTAIN VEHICLES HAVE A SERVICE PROCEDURE PROVIDED REGARDING THE IMPROVEMENT OF 360 DEGREE CAMERA'S CLARITY BY INSPECTING AND REPLACING THE BATTERY, IF NECESSARY AND REPAIRING AND INSPECTING AND REPAIRING ANY CLICKING NOISE IN STEERING COLUMN. MODEL 2015 ESCALADE, ESCALADE ESV. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/GMC/CHEVROLET: ON SOME SUVS, WHEN SHIFTER IN PARK POSITION AND HAVE BEEN IDLING FOR 2 HOURS OR MORE, THE ENGINE WOULD STOP RUNNING. MODEL 2015 ESCALADE (ALL), TAHOE, SUBURBAN, YUKON (ALL). *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET/CADILLAC: INFORMATION PROVIDED ON SOME VEHICLES AND SUV, FOR REPLACEMENT OF CRANKSHAFT, FOR ENGINE REPAIR AND OIL TANK AND LINES WOULD BE REPLACED ON DRY SUMP ENGINES WHEN REPAIRING AND/OR REPLACING. MODEL 2014-16 CORVETTE, SILVERADO, SIERRA, 2016 CTS-V, 2015-16 ESCALADE, SUBURBAN, TAHOE, YUKON, YUKON XL. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC/CADILLAC: TSB HAS AN OWNER'S NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. WATER IS LEAKING ON TO ROOF MOUNTED ANTENNA AND IS PREVENTING ONSTAR SYSTEM TO DETERMINE LOCATION OF VEHICLE BY DISABLING COMPASS, XM RADIO SYSTEM, NAVIGATION. MODEL 2015 ESCALADE, ESCALADE ESV, SILVERADO CREW CAB, SUBURBAN, TAHOE, SIERRA CREW CAB, YUKON, YUKON XL. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a grind, pop, shudder or bind feeling/noise in the steering column when turning left or right. Technician will inspect for the lower column bearing to be out of position and the upper intermediate steering shaft to lower column shaft bolt and nut may be contacting the inhibitor/shiftier cable bracket. Technician will remove the steering column from the vehicle and replace the lower bearing adapter assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on a concern of body pressure booming. This concern may be more noticeable when the active fuel management is engages and the engine is in 4 cylinder mode. The roof sheet metal may not be attached to the roof bows any longer. If equipped with a sunroof it may leak or be misaligned with the roof. Technician is to follow the steps to apply vibration control material between the roof bow and the roof sheet metal. Any roof bow that is no longer bonded to the sheet metal must be repaired. Remove the old material with an appropriate tool. Once the old material is removed install the appropriate thickness foam shim to fill the gap between the roof sheet metal and the roof bow. The foam should be placed in 5 inch lengths and placed in 5 locations along the bow using vibration control material to fill the distance between the foam shim. If the space between the bow is 6 millimeters or less just use the vibration control material.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that stop running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold. If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have One or more tire pressures display dashes, Service Tire Monitor System Message, Remote Keyless Entry poor range or inoperative or ?No Fob Detected? message or Passive entry system inoperative (if equipped). The technician may find any of the following Diagnostic Trouble Codes set in the Body Control Module associated with the vehicle tire pressure sensors: C0750, C0755, C0760, and/or C0765. Technician will inspect the Remote Control Door Lock Receiver antenna system. Before replacing any parts check three locations for the system being unplugged. The locations were the system could be unplugged are Antenna Amplifier Module disconnected from Antenna at right rear quarter glass, Coax cable disconnected at the Antenna Amplifier Module, and Coax cable disconnected at the Remote Control Door Lock Receiver.
Source components: ELECTRICAL SYSTEM · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of addition information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
Source components: ELECTRICAL SYSTEM · SEATS:FRONT ASSEMBLY:POWER ADJUST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the LCT1000 6 Speed Allison, 8L90 and 8L45 8 speed automatic transmission as well as the transmission control module is on restriction through General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
Source components: EQUIPMENT · POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication for the dealer to please communicate to the customer this condition is a normal operating characteristic of their vehicle. Customer's timeshift audio playback is choppy, distorted, skipping, or garbled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with the driver?s door lock cylinder cover missing. The cover may have been removed to access the key cylinder while shipping in transport mode. If the cover is missing inspect the inside of the vehicle to see if the cover was placed inside during shipping. If the cover is missing a replacement can be ordered through the parts department using part number 13596115. A change has been made on the 2015 model with regular production option code AVF to allow the remote keyless entry to work when in transportation mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the door striker cover will be shipped with the vehicle from the assembly plant. Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon Malfunction Indicator Lamp on. Technician should follow published Service Information diagnostics that will lead to an oil pump replacement. Technician should replace the oil pump. If debris is found, the main and rod bearings should be inspected before engine replacement is considered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within?2.0?mm (0.079?in) of the mounting plates. The rotors and pads should be replaced with the updated part number If the pads are out of specification, perform normal Service Information diagnostics to determine the cause of the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of engine misfire/tick noise, Malfunction Indicator Lamp (MIL) On, DTC P0300 set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides radio programming information to correct customer concerns about no XM audio or time shift, radio lock-up, slow response, vertical line between clock and temperature, poor FM reception (Truck Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to download the USB software from TIS2WEB using the vehicle identification number every time a programming event of the human machine interface module is needed. Damage could be caused to the module if USB programmed with the incorrect software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin is requesting information from dealers on a customer concern of A/C inoperative or poor performance on recent built vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin is requesting information from dealers on a customer concern that one or more key transmitter(s) inoperative/not detected or passive entry inoperative while transmitter functions operate as Intended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication for the dealer to please communicate to the customer this condition is a normal operating characteristic of their vehicle. Customer's timeshift audio playback is choppy, distorted, skipping, or garbled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that replacement transfer case halves will not be threaded. No additional thread tapping will be necessary to assemble the transfer case as the attaching metric bolts are self-tapping. Drive the bolts into the new case and torque them to specification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.