2013 Audi A6 Manufacturer communications & TSBs.Page 12
Original record summaries, dates and identifiers for this model-year. Records 1,101–1,200 of 1,660, ordered newest first. Dated records on this page: Aug 9, 2013–Oct 31, 2013.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 31, 2013Service Bulletin/Repair Instructions
A911311 2027718-
NHTSA communication ID: 10121950
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 13-86 dated June 11, 2013. When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver?s voice sounds muffled, as if it is being heard from under water. The microphone seal is damaged during installation into the roof module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: DRIVER INFORMATION DISPLAY MESSAGE SIDE ASSIST UNAVAILABLE AND LANE CHANGE ASSIST IS SPORADIC INOPERATIVE BECAUSE OF SOFTWARE DIAGNOSTIC FAULT. MODEL 2011-2013 A6, A7, A8. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).
NHTSA source summary · Original PDF not reviewed by Recallfolio
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan.
Source components: BACK OVER PREVENTION · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24AD code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the Federal Emissions Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This communication is to inform you of upcoming Update 24AD. Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. Update the ECM software to latest levels via SVM.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 37 number 13-10 dated July 31, 2013. Customer may report that the gearbox warning message is on. DTC P0706 (driving mode sensor, implausible signal) is stored in the transmission control module (TCM), J217 (address 02). There is a reaction between the TCM and the automatic transmission fluid (ATF) in vehicles within a specific VIN range.
Source components: STEERING:GEAR BOX (OTHER THAN RACK AND PINION).
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This vehicle is one of a limited number of specially-built vehicles that are part of the Audi on Demand pilot program in the USA. A Repair Authorization must be obtained for this vehicle when it arrives at an Audi dealership requiring diagnosis or repair. PDI for this vehicle does not require prior authorization or a TAC ticket. For all other concerns, the procedures in this bulletin are mandatory until further notice. Warranty repairs without authorization via a TAC ticket will not be reimbursed. Routine maintenance for this vehicle should be performed only at an authorized Audi AG maintenance facility for Audi on Demand vehicles and should not be performed at the Audi Dealership. Because of the special modifications, SVM work should never be performed on this vehicle. Additionally, a VAS tester should not be hooked into the vehicle under any circumstance except for when the vehicle is being taken out of Transport Mode or when the SRI is being set. Any additional PDI work requiring a VAS tester should not be performed on this vehicle. There may be a warning posted inside of the vehicle at the time of delivery from the port.
NHTSA source summary · Original PDF not reviewed by Recallfolio
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function.
NHTSA source summary · Original PDF not reviewed by Recallfolio
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function.
NHTSA source summary · Original PDF not reviewed by Recallfolio
One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-26 dated August 29, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin is informational only for repairs made to the rear bumper. Under the rear bumper cover, two shields are fitted below the Lane Change Assistance control units. The shields are in place to prevent unwanted reflections from special aftermarket accessories fitted on this vehicle. These reflections can interfere with the function of the Lane Change Assistance system. The shields are in place to prevent unwanted reflections from special aftermarket accessories fitted on this vehicle. These reflections can interfere with the function of the Lane Change Assistance system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When making minor steering movements while driving in a straight line in Audi vehicles with electromechanical power steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up. This Update is in effect until removed. This Update is in effect until removed. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. When making minor steering movements while driving in a straight line in Audi vehicles with electromechanical power steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 17 number 11-24 dated November 11, 2011. Electronic oil consumption measurement - Repair Authorization Model Year 2012. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in the 2009> B8 platform (A4, allroad, A5, A5 Cabriolet, A6, and Q5) equipped with the 2.0 TFSI (CAEB, CPMA) engine, it is possible to measure oil consumption electronically via a Guided Function test plan. The electronic oil consumption measurement will only function on the 2.0 TFSI engine with engine code CAEB and CPMA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This communication is to inform you of that Update 48K8 has been revised to include a warning to ensure that the Bluetooth function of the scan tool must be physically switched off prior to performing this Update. The revised Update will be visible in ElsaWeb and ServiceNet on or about September 27, 2013. Please ensure your technicians are made aware of this new information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 42 number 12-15 dated October 12, 2012. Cracking or clicking noises are heard from the rear of the vehicle in the C pillar area when it is driven over bumps or rough roads. The noise comes from the upper shock absorber mounting.
Source components: STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-73 dated March 7, 2013. The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 13-98 dated August 5, 2013. MMI 3G+ Sound system "popping" and various other technical Issues (K0715 Update). This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). The applicable vehicles can be clearly identified by the SIM card slot on the faceplate of the front MMI mainunit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: ? DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is being maneuvered in or out of a parking spot). ? DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a low diagnosis threshold. ? DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to a low diagnosis threshold.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 96 number 13-63 dated May 29, 2013. Audi Lane Change Assistant deactivates or is sporadically inoperative. Message ?Side Assist Unavailable? is displayed in the Driver Information Display when the system deactivates. Audi Lane Change Assistant can be activated without issue. DTCs are stored in the Lane Change Assistance control module. A software issue within J769 causes a diagnostic fault, which deactivates the Audi Lane Change Assistant temporarily.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 37 number 13-02 dated April 26, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs is stored in the transmission control module (TCM). If DFCCs do not match exactly, this TSB does not apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: THE TRANSMISSION CONTROL MODULE SOFTWARE WOULD ILLUMINATE IN INSTRUMENT CLUSTER AND VEHICLE FAILS TO MOVE AFTER SHIFTING INTO GEAR AND NEW SOFTWARE IS NEEDED TO ADDRESS CONDITION. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 87 number 13-41 dated May 30, 2013. Moisture in the driver or front passenger foot well. Due to a faulty and/or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 48 number 13-35 dated February 14, 2013. The yellow steering symbol is illuminated in the instrument cluster. DTC C10ACF0 (steering end stops not programmed) is logged in the power steering control module, J500 (address word 44). The power steering control module expects to receive a VIN message over the data bus shortly after terminal 15 is turned on. If the VIN message is not received at the expected time, the power steering control module assumes it has been installed in a new vehicle, and it discards the programmed end position values.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 13-94 dated July 24, 2013. The driver?s voice sounds muffled or background noise sounds very loud to other caller during Bluetooth calls. Voice recognition commands are not recognized or voice recognition accuracy is poor. The location of the microphones within the roof module make them susceptible to interference by the vehicle air vents and climate control settings. When the center air vents are pointed upward, they can cause a ?swirling? effect that affects the audio quality of Bluetooth® and voice recognition. This is particularly evident on hot days when the A/C system is set to ?auto?.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 48 number 12-33 dated October 22, 2012. After replacing the electromechanical steering with the control unit J500, the unit cannot be coded via SVM spec/actual. All new replacement power steering control units (J500) must be coded and parameterized using online SVM spec/actual or an SVM code. If the SVM spec/actual returns a response of ?Check Hardware?, then the SVM code is required to code and parameterize the new replacement control unit. The SVM code can be found in Parts Bulletin 9-97, which is available online through ETKA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 19 number 13-43 dated July 12, 2013. The coolant warning light is illuminated. Coolant is leaking from the front intercooler radiator because of stone damage to the radiator. When vehicles are driven on gravel roads, there is a greater chance of front-end stone impact damage to the intercooler radiator.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-20 dated August 2, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. It is possible that the membrane on the vacuum actuator may tear. As a result, the intake manifold flaps do not function.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-89 dated May 2, 2013. MIL on. A cylinder misfire fault (DTC P0301 - P0306) with DTC P130A is stored in the engine control module (ECM), J623 (address word 01).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 97 number 13-36 dated July 10, 2013. The vehicle alarm activates for no reason and it cannot be turned off. The alarm horn does not work. DTC/fault symptom combinations are found in the comfort system control module. The DTC can be static or sporadic. The wiring harness insulation for the alarm horn can be damaged during the vehicle production assembly. Because the cable is routed through the plenum chamber, water can enter into the cable via the damaged insulation. The water causes the alarm to activate for no reason or it causes the alarm horn to not work.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 87 number 13-43 dated July 12, 2013. Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24Z6 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When making minor steering movements while driving in a straight line in Audi vehicles with electromechanical power steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up. This Update is in effect until removed. Procedure is valid only for vehicles that show the 48K8 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. When making minor steering movements while driving in a straight line in Audi vehicles with electromechanical power steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: UPDATED INFORMATION ON POWER STEERING CONTROL UNIT SOFTWARE, IN SOME VEHICLES, WITH ELECTROMECHANICAL POWER STEERING, HAVING SLIGHT IRREGULARITIES, MANUFACTURED A SPECIFIC PERIOD, MAINLY OCCURS WHEN TEMPERATURE IS AT FREEZING POINT. MODEL 2012-2014 A4, A5, Q5, A6, A7. *PE
Source components: ELECTRICAL SYSTEM:SOFTWARE · STEERING:ELECTRIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This communication is to inform you of upcoming Update 48K8. When making minor steering movements while driving in a straight line in Audi vehicles with electromechanical power steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up. Update the power steering control unit to the latest software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 13-53 dated August 7, 2013. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 12-26 dated October 23, 2012. The yellow warning for electromechanical parking park (EPB) appeared once in the instrument cluster. The warning turned off after the ignition was cycled, and there have not been additional occurrences. EPB function was not affected. The adaptive cruise control (ACC) was inoperative once, but it resumed proper operation after the ignition was cycled, and there have not been additional occurrences. DTCs are logged in the EPB control module. There is an issue with the software in the EPB control module that occurs one time. Because the issue only occurs once, replacing the control module could cause an additional occurrence.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
NHTSA source summary · Original PDF not reviewed by Recallfolio
As part of Audi's ongoing commitment to our environment, Audi is extending the Emissions Control Systems Warranty to cover cleaning of the engine cylinder head secondary air ports to remove carbon buildup under specific conditions to 10 years or 120,000 miles, whichever occurs first, from the vehicle's original in-service date for certain 2009-12 Model Year Audi vehicles with 3.2L engine, and certain 2009-2013 Model Year Audi vehicles with 3.0T engines. The vehicle's original in-service date is defined as the date the vehicle was delivered to either the original purchaser or the original lessee; or if the vehicle was first placed in service as a "demonstrator" or "company" car, on the date such vehicle was first placed in service. The warranty extension is fully transferable to subsequent owners. Audi has determined that under certain driving conditions, carbon buildup can occur in the engine cylinder head secondary airports. Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of the on-board diagnostic system. In some locales, an illuminated MIL could cause the vehicle to fail an IM emissions inspection, vehicle registration application could be denied. Audi will diagnose, and if necessary clean the engine cylinder head secondary air ports to remove the carbon buildup at no cost to the customer as long as the vehicle is within the time and mileage limits of the warranty extension. This warranty extension covers only the diagnosis and cleaning of the cylinder head secondary air ports to remove the carbon buildup. Reimbursement is applicable only to the repairs described in this Warranty Bulletin.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various "whistling" noises are heard from the blower motor when it is running, particularly when it is running at lower fan speeds. The noises may be intermittent, and may depend on the outside temperature, the position of the flaps, etc. The noises are subtle, and they may not be heard if the audio system is on or if the vehicle is moving. The noises may be caused by a section of the noise insulation on the heating and air conditioning unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Audi has determined that, under certain driving conditions, carbon buildup can occur in the engine cylinder head secondary air ports. Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL. In some locales, an illuminated Malfunction Indicator Lamp could cause your vehicle to fail an IM emissions inspection, and your vehicle registration application could be denied. Please be aware that other conditions (unrelated to the issue described in this letter) may cause the MIL in your vehicle to illuminate. Customers should be prepared to cover all diagnosis and repair costs for these other, unrelated conditions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing.