The manufacturer’s record · Page 3 of 4
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 370, ordered newest first. Dated records on this page: Jan 13, 2014–Dec 1, 2016.
Back to 2013 Nissan ALTIMA problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10119177
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2016 ALTIMA WITH QR25DE ENGINE; MIL ON WITH DTC P0101 This bulletin applies only to models equipped with 4-cylinder engines. This bulletin has been amended throughout. Discard all previous versions of this bulletin.
Source components: ENGINE.
Source record 10119177 at NHTSANHTSA communication ID: 10109110
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013 ? 2016 ALTIMA; RUST AROUND REAR LICENSE LAMP FINISHER IF YOU CONFIRM When rust is found on the rear deck lid surface in the area surrounding the license lamp finisher (Figure 1) or replacing the license lamp finisher for any reason. ACTION - Replace the license lamp finisher with the new replacement part listed in the Parts Information. - Refer to the Electronic Service Manual (ESM), section EXT ? Exterior for removal and installation information. - Repair any damaged surfaces that were in direct contact with the license lamp finisher.
Source components: EQUIPMENT · STRUCTURE:BODY.
Source record 10109110 at NHTSANHTSA communication ID: 10119266
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
Source components: ENGINE.
Source record 10119266 at NHTSANHTSA communication ID: 10119282
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
Source components: ENGINE.
Source record 10119282 at NHTSANHTSA communication ID: 10119279
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2014 ALTIMA; A/C DOES NOT BLOW COLD AND CLUTCH DOES NOT ENGAGE IF YOU CONFIRM The air conditioner does not blow cold air, AND The magnet clutch is determined to be the cause when following the diagnosis procedure in the HAC section of the Electronic Service Manual (ESM). ACTION Replace the magnet coil. - Refer to SERVICE PROCEDURE on page 3. NOTE: Do NOT discharge the refrigerant or remove the A/C compressor for this procedure.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10119279 at NHTSANHTSA communication ID: 10119276
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2014 ALTIMA AND 2014-2016 ROGUE; MIL ON WITH DTC P0776, P1715 MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin has been amended to remove 2015-2016 Altima from the Applied Vehicles. Please discard previous versions of this bulletin.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10119276 at NHTSANHTSA communication ID: 10120586
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10120586 at NHTSANHTSA communication ID: 10091576
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NO AUDIO DURING PHONE CALL WITH APPLE IOS 10, NAVIGATION SYSTEM REBOOTS, AND/OR AUDIO CONTROLS WILL NOT RESPOND THIS BULLETIN HAS BEEN AMENDED. THE TITLE AND IF YOU CONFIRM SECTION HAVE BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10091576 at NHTSANHTSA communication ID: 10091608
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NISSAN; DOORS DIFFICULT TO CLOSE WITH TEMPERATURE BELOW FREEZING IF YOU CONFIRM: THE FOLLOWING INCIDENT, OR THE CUSTOMER REPORTS THIS INCIDENT: - THE VEHICLE HAS BEEN SETTING (NOT RUNNING) IN TEMPERATURES BELOW 14°F (-10°C) FOR AN EXTENDED PERIOD (SUCH AS OVERNIGHT). THEN - A SIDE DOOR IS OPENED. THEN - THE DOOR IS DIFFICULT TO CLOSE/LATCH, WILL NOT CLOSE/LATCH WITH NORMAL PRESSURE; REQUIRES ADDITIONAL EFFORT TO CLOSE/LATCH, OR THE DOOR MAY ONLY LATCH HALF WAY. THEN - THE DOOR WILL CLOSE/LATCH NORMALLY WHEN THE VEHICLE HAS WARMED UP (VEHICLE LEFT IN THE SUN, MOVED INDOORS, OR DRIVEN FOR SEVERAL MINUTES). NOTE: O THE ABOVE INCIDENT DOES NOT APPLY TO SLIDING SIDE DOORS OR A REAR HATCH (BACK DOOR). O THE ABOVE INCIDENT, IF IT SHOULD OCCUR, COULD BE CONFIRMED OR REPORTED FOR ONE OR MORE SIDE DOORS. ACTION REPLACE THE DOOR LOCK FOR THE AFFECTED DOOR. - DO NOT REPLACE ALL SIDE DOOR LOCKS AUTOMATICALLY. REPLACE ONLY THE DOOR LOCK OF THE DOOR(S) WITH THE INCIDENT AS DESCRIBED UNDER IF YOU CONFIRM. - REFER TO THE ELECTRONIC SERVICE MANUAL (ESM), SECTION DLK DOOR & LOCK FOR REPLACEMENT PROCEDURE."
Source components: LATCHES/LOCKS/LINKAGES:DOORS:LATCH.
Source record 10091608 at NHTSANHTSA communication ID: 10091527
NHTSA source summary · Original PDF not reviewed by Recallfolio
"2013-2015 ALTIMA WITH 4-CYL ENGINE; CABIN BOOM AND/OR STEERING/FLOOR VIBRATION WHILE DRIVING 4-CYLINDER ENGINE ONLY IF YOU CONFIRM: A BOOM OR DRONE SENSATION IS HEARD IN THE CABIN AREA AND/OR A VIBRATION IS FELT IN THE FLOOR AND/OR STEERING WHEEL WHEN DRIVING AND THE ENGINE IS APPROXIMATELY 1,800 RPM. ACTION: 1. CHECK THE GAP BETWEEN THE RUBBER AND METAL PORTIONS OF THE FRONT TUBE EXHAUST HANGER (SEE FIGURE 1 AND PAGE 2, FIGURE 2). 2. IF LESS THAN 1 MM (0.04 INCH) GAP, ADD SHIMS (FLAT WASHERS) BETWEEN THE FRONT SUSPENSION MEMBER AND FRONT EXHAUST TUBE HANGER. SEE PAGE 2, FIGURE 2 AND 3. - MAXIMUM SHIM THICKNESS: 4.6 MM (0.18 INCH)"
Source components: ENGINE.
Source record 10091527 at NHTSANHTSA communication ID: 10091506
NHTSA source summary · Original PDF not reviewed by Recallfolio
"2013-2016 ALTIMA AND 2014-2016 ROGUE; MIL ON WITH DTC P0776, P1715 MAY HAVE HESITATION AND/OR LACK OF POWER ALTIMA WITH 4-CYLINDER ENGINE ONLY THIS BULLETIN HAS BEEN AMENDED. THE TITLE IS CHANGED, A DTC IS ADDED UNDER IF YOU CONFIRM, AND TCM REPROGRAMMING IS ADDED TO THE SERVICE PROCEDURE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10091506 at NHTSANHTSA communication ID: 10091503
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN."
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10091503 at NHTSANHTSA communication ID: 10091413
NHTSA source summary · Original PDF not reviewed by Recallfolio
"REMOTE ENGINE START NOT WORKING THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE TO ITEMS 1, 4, AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON, UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM."
Source components: ENGINE.
Source record 10091413 at NHTSANHTSA communication ID: 10192841
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10192841 at NHTSANHTSA communication ID: 10192840
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · TIRES.
Source record 10192840 at NHTSANHTSA communication ID: 10192834
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM One or more of the DTCs listed in Table A are stored in the Transmission Control Module (TCM). And No other DTCs are stored other than what are listed in Table A. And The diagnostic procedures in the Electronic Service Manual (ESM) for each DTC in Table A, that is stored in the TCM, has been performed and indicates that the CVT assembly must be replaced. NOTE: Do not replace the CVT. ACTION Replace the CVT valve body assembly (control valve) with a unit from Parts Information. See page 2 for important information when replacing the CVT control valve.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10192834 at NHTSANHTSA communication ID: 10192833
NHTSA source summary · Original PDF not reviewed by Recallfolio
IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
Source components: EQUIPMENT · POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10192833 at NHTSANHTSA communication ID: 10192829
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The following, or the customer reports the following: - Intermittently there is low power when accelerating, And/or - The stop lamps (brake lights) stay ON after releasing the brake pedal, with the ignition ON or OFF. ACTION - Delete the stop lamp relay and bypass the stop lamp relay circuit. - Replace the stop lamp switch with the one listed in PARTS INFORMATION. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · ENGINE · EXTERIOR LIGHTING:BRAKE LIGHTS.
Source record 10192829 at NHTSANHTSA communication ID: 10192816
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration) AND One of these DTCs is stored: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE - If a transmission judder (as described above) is not reported, this bulletin does not apply. - If either P17F0 or P17F1 are not stored, this bulletin does not apply. - NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart in this bulletin. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVTinspection possible. See this bulletin for further detail.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
Source record 10192816 at NHTSANHTSA communication ID: 10192813
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · STEERING.
Source record 10192813 at NHTSANHTSA communication ID: 10194176
NHTSA source summary · Original PDF not reviewed by Recallfolio
2-Sensor occupant classification System Diagnostics and Information
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10194176 at NHTSANHTSA communication ID: 10192805
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10192805 at NHTSANHTSA communication ID: 10192801
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
Source components: EQUIPMENT:OTHER:LABELS · FORWARD COLLISION AVOIDANCE.
Source record 10192801 at NHTSANHTSA communication ID: 10194179
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan; Procedure to clean CVT Transmission fluid coolers
Source components: POWER TRAIN.
Source record 10194179 at NHTSANHTSA communication ID: 10194192
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2016 Altima and 2014-2016 Rogue; MIL on with DTC P0776
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT:BELT.
Source record 10194192 at NHTSANHTSA communication ID: 10075093
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE.
Source record 10075093 at NHTSANHTSA communication ID: 10194180
NHTSA source summary · Original PDF not reviewed by Recallfolio
Enhanced Diagnostic Logic for CVT Judder
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10194180 at NHTSANHTSA communication ID: 10192793
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on Applied Vehicles. The new DTCs are: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. Refer to page 4, step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. NOTE:The current TCM Part Numbers in this bulletin have been updated. The vehicle you are working on may require reprogramming per this bulletin again. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module) See this bulletin for further detail.
Source components: EQUIPMENT · POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10192793 at NHTSANHTSA communication ID: 10194191
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2015 Altima and 2014-2016 Rogue; MIL on with DTC P0776
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT:BELT.
Source record 10194191 at NHTSANHTSA communication ID: 10194190
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2015 Altima; CVT delayed engagement when shifting into drive or reverse
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10194190 at NHTSANHTSA communication ID: 10194189
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2016 Altima and 2014-2016 Rogue; CVT Judder and DTC P17F0 or P17F1 stored (4 cyl engine only)
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10194189 at NHTSANHTSA communication ID: 10192791
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The CVT has a delayed engagement when shifting into Drive or Reverse, and there are no DTCs stored in the ECM and/or TCM. ACTION: Refer to page 5, step 6 in the SERVICE PROCEDURE of this bulletin to check if TCM reprogramming applies to the vehicle you are working on. 1. Reprogram the TCM, if reprogramming applies. 2. Inspect the CVT belt per the SERVICE PROCEDURE in this bulletin. 3. Perform CVT repairs based on inspection results. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10192791 at NHTSANHTSA communication ID: 10075092
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE.
Source record 10075092 at NHTSANHTSA communication ID: 10075091
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: POWER TRAIN.
Source record 10075091 at NHTSANHTSA communication ID: 10075090
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: POWER TRAIN.
Source record 10075090 at NHTSANHTSA communication ID: 10194181
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pathfinder, Quest, Murano, Maxima, Altima V6, CVT Judder and DTC P17F0 or P17F1 Stored
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10194181 at NHTSANHTSA communication ID: 10194173
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT/TDCM Calibration Data "Write" Procedure
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10194173 at NHTSANHTSA communication ID: 10194184
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel Filler Cap tether clip service information
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP.
Source record 10194184 at NHTSANHTSA communication ID: 10192787
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
Source components: EQUIPMENT · FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP.
Source record 10192787 at NHTSANHTSA communication ID: 10194207
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2016 Altima with QR25DE Engine; MIL oin with DTC P0116
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE.
Source record 10194207 at NHTSANHTSA communication ID: 10075208
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2016 ALTIMA WITH QR25DE ENGINE; MIL ON WITH DTC P0116 IF YOU CONFIRM The MIL is ON with P0116 Engine Coolant Temperature (ECT SENSOR) stored, and There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. IMPORTANT:
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
Source record 10075208 at NHTSANHTSA communication ID: 10192780
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The MIL is ON with P0116 Engine Coolant Temperature (ECT SENSOR) stored, and There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING.
Source record 10192780 at NHTSANHTSA communication ID: 10192773
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of the following DTCs are stored in the TCM: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: - If a transmission judder (as described above) is NOT reported by the customer, this bulletin does not apply. - If DTC P17F0 or P17F1 was NOT found stored, this bulletin does not apply. - NTB15-083, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart on page 2. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVT inspection possible. See this bulletin for further detail.
Source components: POWER TRAIN.
Source record 10192773 at NHTSANHTSA communication ID: 10192769
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A customer concern of while turning the steering wheel or when driving at low speed (straight or turning), a high pitch power steering noise can be heard. * Only while seated inside the vehicle And * With all of the windows up NOTE: If the audio and/or HVAC systems are turned ON it may be difficult to hear this issue. ACTION Install an Insulator onto the end of the power steering pump motor housing with the Service Procedure starting on the next page. Please see this bulletin for further details.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE · POWER TRAIN · STEERING · VISIBILITY · WHEELS.
Source record 10192769 at NHTSANHTSA communication ID: 10194199
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan; Power steering noise heard inside vehicle with windows closed
Source components: EQUIPMENT · STEERING.
Source record 10194199 at NHTSANHTSA communication ID: 10192750
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
Source components: EXTERIOR LIGHTING.
Source record 10192750 at NHTSANHTSA communication ID: 10192727
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
Source components: VISIBILITY.
Source record 10192727 at NHTSANHTSA communication ID: 10192725
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: A whine or grind type noise heard during acceleration and/or constant highway speeds. -The level of noise may increase as vehicle speed increases AND there are no other drivability issues or stored DTCs related to the CVT assembly (CVT). ACTION: Refer to the REPAIR FLOW CHART on page 3 for repair procedure. Refer to page 2 for information on special service tools. NOTE: Parts Kit #1 (see PARTS INFORMATION) must be available at the time the reduction gear bearing shim selection procedure, starting on page 11, is to be performed. See this bulletin for further detail.
Source components: BACK OVER PREVENTION · POWER TRAIN.
Source record 10192725 at NHTSANHTSA communication ID: 10192720
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The function to detect the last item to trigger the vehicles theft alarm system can now be accessed with CONSULT-III plus (C-III plus). This function can be accessed by selecting: * Diagnosis (All Systems) or Diagnosis (One System). Then * BCM Then * THEFT ALM Then * Work Support Then * THEFT ALM TRG. See this bulletin for further details.
Source components: ELECTRICAL SYSTEM.
Source record 10192720 at NHTSANHTSA communication ID: 10194193
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2015 Altima; Low power/Stop lamps stay on
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10194193 at NHTSANHTSA communication ID: 10075094
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ELECTRICAL SYSTEM.
Source record 10075094 at NHTSANHTSA communication ID: 10074573
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10074573 at NHTSANHTSA communication ID: 10192707
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM.
Source record 10192707 at NHTSANHTSA communication ID: 10192687
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM.
Source record 10192687 at NHTSANHTSA communication ID: 10192679
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
Source components: VISIBILITY.
Source record 10192679 at NHTSANHTSA communication ID: 10192677
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
Source components: VISIBILITY.
Source record 10192677 at NHTSANHTSA communication ID: 10074569
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: EQUIPMENT.
Source record 10074569 at NHTSANHTSA communication ID: 10192663
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail.
Source components: PARKING BRAKE · SEAT BELTS · VEHICLE SPEED CONTROL.
Source record 10192663 at NHTSANHTSA communication ID: 10192661
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION: The Navigation (NAVI) SD Map Data Cards are not interchangeable between the two versions of NAVI units offered in Nissan vehicles that use this type of map data. * If the wrong SD Map Data Card is used, the NAVI will display an update screen (Figures 1 and 2, reference only) and will only accept Cancel. * If this screen is displayed, install the correct SD Map Data Card, found in table A on page 2, and the NAVI unit will return to correct operation. See this bulletin for further detail.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10192661 at NHTSANHTSA communication ID: 10192650
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10192650 at NHTSANHTSA communication ID: 10192645
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on applied vehicles. These new DTC?s are: P17F1 (CVT_JUDDER (C/U INSPECTION)) P17F0 (CVT_JUDDER (T/M INSPECTION)) ACTION: 1. Refer to step 6 and TABLE A on page 4 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you areworking on. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module). Please see this bulletin for further details.
Source components: POWER TRAIN.
Source record 10192645 at NHTSANHTSA communication ID: 10192643
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM All of the following - The engine will not start (no crank; starter will not engage) when pushing the ignition switch, and I-Key Error message is displayed in the combination meter, and DTC B2604 (PNP/Clutch Switch) is stored, past or present. ACTION Perform adjustment of the shift control cable per the Service Procedure in this bulletin. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM.
Source record 10192643 at NHTSANHTSA communication ID: 10192638
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
Source components: BACK OVER PREVENTION · LANE DEPARTURE · SERVICE BRAKES · WHEELS.
Source record 10192638 at NHTSANHTSA communication ID: 10192615
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT.
Source record 10192615 at NHTSANHTSA communication ID: 10192614
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason, follow the steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10192614 at NHTSANHTSA communication ID: 10192608
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION For the Applied Vehicles in this bulletin, when an ABS Actuator and Electric Unit (ABS control unit) is replaced for any reason, Configuration of the ABS Control Unit must be performed. If Configuration is not performed, DTC C1170 (VARIANT CODING) will be stored. The Service Procedure in this bulletin contains the steps for performing ABS Control Unit Manual Configuration. See this bulletin for further detail.
Source components: EQUIPMENT.
Source record 10192608 at NHTSANHTSA communication ID: 10057133
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: 2013-2015 ALTIMA, MURANO, ROGUE(T32). CONFIGURATION MUST BE PERFORMED ON THE SELECTED VEHICLES WHEN AN ABS CONTROL UNIT IS BEING REPLACED. *LJ UPDATED 9/10/15. *PE
Source components: SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT.
Source record 10057133 at NHTSANHTSA communication ID: 10192605
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear CV-type axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. - For 2007-2013 Versa and 2013 LEAF vehicles, see the Service Procedure torque specifications on page 4. See this bulletin for further detail.
Source components: BACK OVER PREVENTION · EQUIPMENT · POWER TRAIN · WHEELS.
Source record 10192605 at NHTSANHTSA communication ID: 10192597
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
Source components: BACK OVER PREVENTION · EQUIPMENT · SERVICE BRAKES · STEERING · WHEELS.
Source record 10192597 at NHTSANHTSA communication ID: 10192591
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
Source record 10192591 at NHTSANHTSA communication ID: 10192574
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
Source components: WHEELS.
Source record 10192574 at NHTSANHTSA communication ID: 10192552
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Some of the wheel alignment specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the 2013-2015 Altima Sedan Electronic Service Manuals are incorrect. Updated Electronic Service Manuals will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the updated service information hyperlinked in this bulletin.
Source components: ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · SUSPENSION · WHEELS.
Source record 10192552 at NHTSANHTSA communication ID: 10192542
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
Source components: WHEELS.
Source record 10192542 at NHTSANHTSA communication ID: 10192532
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
Source components: EQUIPMENT.
Source record 10192532 at NHTSANHTSA communication ID: 10192524
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
Source components: POWER TRAIN · STEERING.
Source record 10192524 at NHTSANHTSA communication ID: 10192520
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The MIL is ON with DTC P0101 for Mass Air Flow sensor (MAF) stored in the ECM, AND there are no drivability concerns. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
Source components: BACK OVER PREVENTION.
Source record 10192520 at NHTSANHTSA communication ID: 10192513
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
Source components: AIR BAGS · BACK OVER PREVENTION · EQUIPMENT.
Source record 10192513 at NHTSANHTSA communication ID: 10192508
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
Source components: EQUIPMENT.
Source record 10192508 at NHTSANHTSA communication ID: 10192491
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ----- Page 2 - Two (2) Intelligent Keys Are Lost ----- Page 3 See this bulletin for further detail.
Source components: STRUCTURE.
Source record 10192491 at NHTSANHTSA communication ID: 10192486
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The OCS (Occupant Classification System) sensors for the Applied Vehicles are now available as service parts. See this bulletin for further detail.
Source components: AIR BAGS · ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10192486 at NHTSANHTSA communication ID: 10192478
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10192478 at NHTSANHTSA communication ID: 10192474
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10192474 at NHTSANHTSA communication ID: 10192471
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION A two-piece design front engine mount is currently being used for the applied vehicles listed. A single thunk noise may be heard on the first acceleration of the day from this type of mount and is considered normal operation. The mount has also been designed with built in free-play that is normal. Under normal driving conditions: * A "thunk" noise may be heard on the first acceleration of the day. And * Does not occur again, or at any other time. DO NOT REPLACE THE MOUNT: * If it has free play or a "single event" thunk sound on the first acceleration of the day. This is considered a normal characteristic of this type of engine mount. * If a shift shock condition is present when shifting from park into gear or between any combination of gears. This condition is due to transmissions line pressures and not movement of the mount. NOTE: Refer to the Electronic Service Manual section TM - Transaxle & Transmission for further diagnostic information on shift shock. See this bulletin for further details.
Source components: ENGINE · STRUCTURE.
Source record 10192471 at NHTSANHTSA communication ID: 10192464
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting an inventory inspection on 105,290 specific MY2013-15 Nissan ALT, PTH, LEF, MUR, NV2, NVT, SEN, and VER NOTE vehicles to inspect the software on the OCS ECU.
Source components: ENGINE · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
Source record 10192464 at NHTSANHTSA communication ID: 10192436
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A squeaking/ticking noise is coming from the Headliner between the Moonroof and B-pillar area shown in Figure A. * Can occur on rough roads or during conditions that cause body flex such as when entering or exiting a sloped driveway. ACTION Remove Moonroof brackets and apply UHMW tape, from Squeak and Rattle kit J-50397 (part # J-50397-15), to the bracket. Please see this bulletin for further details.
Source components: EQUIPMENT · STRUCTURE · VISIBILITY:SUN/MOON ROOF ASSEMBLY.
Source record 10192436 at NHTSANHTSA communication ID: 10056181
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: REGARDING SOME VEHICLES USING TWO STAIN GAUGE OCCUPANT CLASSIFICATION SYSTEM (OCS) OPERATION, AND THE PRESSURES NECESSARY DUE TO DIFFERENT RESPONSE OF OCCUPANT SEATING POSTURE. MODEL 2013-2015 ALTIMA, SENTRA, PATHFINDER, LEAF, NV200, NV200 TAXI, ROGUE. *PE
Source components: EQUIPMENT:ELECTRICAL.
Source record 10056181 at NHTSANHTSA communication ID: 10192422
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The purpose of this bulletin is to clarify language contained in the owner?s manual language for the APPLIED VEHICLES. For the APPLIED VEHICLES, the below language supersedes similar language in existing owner?s manuals. Future printings of owner?s manuals for the APPLIED VEHICLES will also contain the below language. For the APPLIED VEHICLES: NISSAN recommends using Genuine NISSAN NS-3 CVT Fluid ONLY in NISSAN CVTs. Do not mix with other fluids. Do not use Automatic transmission fluid (ATF) or Manual Transmission fluid in a NISSAN CVT, as it may damage the CVT. Damage caused by the use of fluids other than as recommended is not covered under NISSAN's New Vehicle Limited Warranty. Using fluids that are not equivalent to Genuine NISSAN NS-3 CVT Fluid may also damage the CVT. Damage caused by the use of fluids other than as recommended is not covered under NISSAN's New Vehicle Limited Warranty. See this bulletin for further detail.
Source components: EQUIPMENT · POWER TRAIN.
Source record 10192422 at NHTSANHTSA communication ID: 10192421
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Applied vehicles equipped with a CVT have a "cap" that appears to be a fluid level gauge. This "cap" will NOT have a gauge or "dipstick". This is normal. Do NOT replace the "cap" because it is thought to have a "dipstick". The fluid level is not checked from this location. The fluid level for applied vehicles is checked from the oil pan (refer to the appropriate section of the Electronic Service Manual [ESM]). Whenever checking, filling, or topping off a CVT's fluid level of an applied vehicle for any reason, use the procedure outlined in the appropriate section of the ESM. See this bulletin for further detail.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
Source record 10192421 at NHTSANHTSA communication ID: 10192394
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10192394 at NHTSANHTSA communication ID: 10192378
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A squeal/squeak noise is coming from the rear brakes: - When the brakes are either hot (after 10-15 minutes of driving) or cold (after vehicle has not been driven for 2-3 hours), - while moving forward or in reverse, - at speeds less than 10 MPH, - while traveling straight, AND - with light to moderate brake application (pedal pressure). NOTE - These are the typical conditions in which to duplicate the rear brake squeal/squeak; however, these conditions are not intended to detail all of the possible conditions in which the noise may occur. When attempting to duplicate this noise it is important to have a second person safely standing outside of the vehicle to determine if the noise is coming from the front or rear brakes. ACTION Replace the rear brake pads and the rear brake hardware kit with the parts listed in the Parts Information section of this bulletin. - Refer to the Electronic Service Manual (ESM), section BR - Brake System, for removal and installation information. See this bulletin for further detail.
Source components: EQUIPMENT · SERVICE BRAKES, HYDRAULIC.
Source record 10192378 at NHTSANHTSA communication ID: 10192377
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The customer states the following: - While driving, the audio setting in the Vehicle Information Display (VID) is blank while displaying normally in the audio unit. - All other items in the VID display normally i.e. temperature, MPG, etc. - Items above and below the VID display normally i.e. DTE, gear selection, etc. - The issue occurs with the ignition ON or the engine running. - The audio setting normally displays in the combination meter with the audio system on. NOTE: With the ignition in the ACC position, the audio display will go off after approximately 5 seconds. This is normal. ACTION: Replace the combination meter assembly with the one listed in PARTS INFORMATION. NOTE: Do NOT replace the audio unit or any other related parts for this issue, if it should occur. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10192377 at NHTSANHTSA communication ID: 10192372
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The customer is experiencing a noise coming from the passenger side engine compartment and The source of the noise is confirmed to be the Hydraulic Electric Power Steering (H-EPS) and The noise is louder than the normal operational noise of the H-EPS. Notes: - Some operational noise from the front of the vehicle generated by the H-EPS is normal when the steering wheel is operated. - Comparing the incident vehicle to a "known good vehicle" will help determine if the H-EPS noise is louder than normal. ACTION: Refer to the Repair Flow Chart on page 2. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · STEERING.
Source record 10192372 at NHTSANHTSA communication ID: 10192370
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION - The Applied Vehicles are equipped with a hood ledge finisher on the passenger (RH) side only. - Do not submit a claim for a "missing" hood ledge finisher on driver's (LH) side. See this bulletin for further detail.
Source components: EQUIPMENT · STRUCTURE:BODY:HOOD.
Source record 10192370 at NHTSANHTSA communication ID: 10192361
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10192361 at NHTSANHTSA communication ID: 10192354
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM:WIRING.
Source record 10192354 at NHTSANHTSA communication ID: 10192340
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The base model of the 2013-2014 Altima 2.5 Sedan is not equipped with an engine cover. Base model 2013 Altima 2.5 Sedan vehicles built before the VINs and dates shown below are not equipped with exhaust finishers. 1N4AL3AP(*)DC 227196 // March 13, 2013 1N4AL3AP(*)DN 530748 // March 8, 2013 The base model can be identified by the model designation on the trunk lid. The trunk lid will not have any of the following: - S - SV - SL Do not attempt to install an engine cover or exhaust finishers* under warranty on the base model. Installation of these parts on this model is not covered under warranty. *If vehicle was built before VINs and dates shown above.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10192340 at NHTSANHTSA communication ID: 10192328
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: When slowly raising the engine RPM, a hissing, whining, and/or air leak type noise of an applied vehicle is heard coming from the driver side lower instrument panel area. - The noise is verified while the vehicle is parked and the transmission is in the Park (P) position. NOTE: A customer may state the noise can be duplicated during light to moderate acceleration in the 10 - 40 MPH range. ACTION: 1. Remove the ground wire connected between the transmission and driver side frame rail. 2. If the noise stops after repeating the procedure under IF YOU CONFIRM, replace the ground wire with the one listed in PARTS INFORMATION. See this bulletin for further detail.
Source components: ENGINE · POWER TRAIN.
Source record 10192328 at NHTSANHTSA communication ID: 10192305
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
Source components: AIR BAGS · EQUIPMENT.
Source record 10192305 at NHTSANHTSA communication ID: 10192298
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: A wind or road type noise is coming from either front door around the door mirror area AND / OR A rattle or flutter type noise is heard from the window or mirror area(s). NOTE: The noises reduce during a road test after applying "painter's tape" or suitable covering where noted in Figure 1. - The rattle noise is coming from the lower cover due to loose fit. ACTION: Refer to the REPAIR FLOW CHART on page 2. See this bulletin for further detail.
Source components: EQUIPMENT · VISIBILITY.
Source record 10192298 at NHTSANHTSA communication ID: 10192293
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
Source components: ENGINE · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
Source record 10192293 at NHTSA