The manufacturer’s record · Page 5 of 8
Original record summaries, dates and identifiers for this model-year. Records 401–500 of 788, ordered newest first. Dated records on this page: Jun 24, 2015–Mar 30, 2016.
Back to 2014 Mazda CX-5 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10185967
NHTSA source summary · Original PDF not reviewed by Recallfolio
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes âÂÂlinkedâ to the VIN of that vehicle.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10185967 at NHTSANHTSA communication ID: 10185966
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article provides HVAC heater/defroster operating tips using Mode selector dial. This includes the use of intermediate positions.
Source components: EQUIPMENT · UNKNOWN OR OTHER.
Source record 10185966 at NHTSANHTSA communication ID: 10091406
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.
Source components: EQUIPMENT.
Source record 10091406 at NHTSANHTSA communication ID: 10091393
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS ARTICLE PROVIDES HVAC HEATER/DEFROSTER OPERATING TIPS USING MODE SELECTOR DIAL. THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.
Source components: VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
Source record 10091393 at NHTSANHTSA communication ID: 10091265
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.
Source components: EQUIPMENT.
Source record 10091265 at NHTSANHTSA communication ID: 10091263
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS ARTICLE PROVIDES HVAC HEATER/DEFROSTER OPERATING TIPS USING MODE SELECTOR DIAL. THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.
Source components: VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:HEATER CORE.
Source record 10091263 at NHTSANHTSA communication ID: 10185969
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a rattle type noise coming from the rear of the vehicle when driving on rough roads. This may be caused by a loose spare tire jack.
Source components: EQUIPMENT.
Source record 10185969 at NHTSANHTSA communication ID: 10185968
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a blurry rear view monitor display. This may be caused by an aftermarket accessory device.
Source components: ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:SOFTWARE · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10185968 at NHTSANHTSA communication ID: 10091433
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT A BLURRY REAR VIEW MONITOR DISPLAY. THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE
Source components: EQUIPMENT.
Source record 10091433 at NHTSANHTSA communication ID: 10091361
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT A RATTLE TYPE NOISE COMING FROM THE REAR OF THE VEHICLE WHEN DRIVING ON ROUGH ROADS. THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK.
Source components: EQUIPMENT.
Source record 10091361 at NHTSANHTSA communication ID: 10091266
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT A BLURRY REAR VIEW MONITOR DISPLAY. THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE.
Source components: EQUIPMENT.
Source record 10091266 at NHTSANHTSA communication ID: 10185951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Beginning with the CX-5 and Mazda6 models, grip type front and rear stabilizer bushings have been incorpo-rated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
Source components: STRUCTURE.
Source record 10185951 at NHTSANHTSA communication ID: 10101088
NHTSA source summary · Original PDF not reviewed by Recallfolio
BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.
Source components: SUSPENSION:FRONT:STABILIZER BAR.
Source record 10101088 at NHTSANHTSA communication ID: 10090861
NHTSA source summary · Original PDF not reviewed by Recallfolio
BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.
Source components: SUSPENSION.
Source record 10090861 at NHTSANHTSA communication ID: 10185908
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with LED or Discharge type headlights may exhibit white milky stains on the inner sur-face of the headlight lens. Some customers may complain of the poor appearance. This concern is caused by gas that emits from a gasket in the lamp unit. The gas adheres to the inner surface of the headlight lens and reacts with the anti-clouding coating and moisture in the air to create white milky stains. The gasket material has been improved to eliminate this concern.
Source components: EXTERIOR LIGHTING · EXTERIOR LIGHTING:HEADLIGHTS:CONCEALMENT DEVICES.
Source record 10185908 at NHTSANHTSA communication ID: 10101083
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EQUIPPED WITH LED OR DISCHARGE TYPE HEADLIGHTS MAY EXHIBIT WHITE MILKY STAINS ON THE INNER SUR-FACE OF THE HEADLIGHT LENS. SOME CUSTOMERS MAY COMPLAIN OF THE POOR APPEARANCE. THIS CONCERN IS CAUSED BY GAS THAT EMITS FROM A GASKET IN THE LAMP UNIT. THE GAS ADHERES TO THE INNER SURFACE OF THE HEADLIGHT LENS AND REACTS WITH THE ANTI-CLOUDING COATING AND MOISTURE IN THE AIR TO CREATE WHITE MILKY STAINS. THE GASKET MATERIAL HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10101083 at NHTSANHTSA communication ID: 10090823
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EQUIPPED WITH LED OR DISCHARGE TYPE HEADLIGHTS MAY EXHIBIT WHITE MILKY STAINS ON THE INNER SUR-FACE OF THE HEADLIGHT LENS. SOME CUSTOMERS MAY COMPLAIN OF THE POOR APPEARANCE. THIS CONCERN IS CAUSED BY GAS THAT EMITS FROM A GASKET IN THE LAMP UNIT. THE GAS ADHERES TO THE INNER SURFACE OF THE HEADLIGHT LENS AND REACTS WITH THE ANTI-CLOUDING COATING AND MOISTURE IN THE AIR TO CREATE WHITE MILKY STAINS. THE GASKET MATERIAL HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10090823 at NHTSANHTSA communication ID: 10185907
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped.
Source components: STEERING · SUSPENSION:FRONT:SHOCK ABSORBER.
Source record 10185907 at NHTSANHTSA communication ID: 10101081
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS · SUSPENSION:FRONT:SHOCK ABSORBER.
Source record 10101081 at NHTSANHTSA communication ID: 10090821
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.
Source components: SUSPENSION.
Source record 10090821 at NHTSANHTSA communication ID: 10185906
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded, P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.
Source components: ENGINE AND ENGINE COOLING.
Source record 10185906 at NHTSANHTSA communication ID: 10185904
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the steering wheel is off center more than 3" even when driving straight on a flat road.
Source components: STEERING.
Source record 10185904 at NHTSANHTSA communication ID: 10101069
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.P0015:00 - EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
Source components: ENGINE · ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10101069 at NHTSANHTSA communication ID: 10101062
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD.
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
Source record 10101062 at NHTSANHTSA communication ID: 10090817
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.P0015:00 - EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
Source components: ENGINE.
Source record 10090817 at NHTSANHTSA communication ID: 10090812
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD.
Source components: STEERING.
Source record 10090812 at NHTSANHTSA communication ID: 10213462
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Technical Service Bulletins March 2016
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10213462 at NHTSANHTSA communication ID: 10185958
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter a 2013-2016 CX-5 with DTC P011A with overheating and/or no heat from the heater, compare the heater performance to another CX-5. If another CX-5 is not available, check the heater core flow and if restricted, drain/replace coolant and replace the heater core. NOTE: If the code is set by itself, without overheating and/or no heat from the heater, follow the Workshop Manual on MS3 online.
Source components: EQUIPMENT.
Source record 10185958 at NHTSANHTSA communication ID: 10091444
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU ENCOUNTER A 2013-2016 CX-5 WITH DTC P011A WITH OVERHEATING AND/OR NO HEAT FROM THE HEATER, COMPARE THE HEATER PERFORMANCE TO ANOTHER CX-5. IF ANOTHER CX-5 IS NOT AVAILABLE, CHECK THE HEATER CORE FLOW AND IF RESTRICTED, DRAIN/REPLACE COOLANT AND REPLACE THE HEATER CORE. NOTE: IF THE CODE IS SET BY ITSELF, WITHOUT OVERHEATING AND/OR NO HEAT FROM THE HEATER, FOLLOW THE WORKSHOP MANUAL ON MS3 ONLINE.
Source components: ENGINE.
Source record 10091444 at NHTSANHTSA communication ID: 10084961
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU ENCOUNTER A 2013-2016 CX-5 WITH DTC P011A WITH OVERHEATING AND/OR NO HEAT FROM THE HEATER, COMPARE THE HEATER PERFORMANCE TO ANOTHER CX-5. IF ANOTHER CX-5 IS NOT AVAILABLE, CHECK THE HEATER CORE FLOW AND IF RESTRICTED, DRAIN/REPLACE COOLANT AND REPLACE THE HEATER CORE. NOTE: IF THE CODE IS SET BY ITSELF, WITHOUT OVERHEATING AND/OR NO HEAT FROM THE HEATER, FOLLOW THE WORKSHOP MANUAL ON MS3 ONLINE.
Source components: ENGINE AND ENGINE COOLING:ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10084961 at NHTSANHTSA communication ID: 10213431
NHTSA source summary · Original PDF not reviewed by Recallfolio
White Milky stains on inner surface of headlight lens
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10213431 at NHTSANHTSA communication ID: 10213430
NHTSA source summary · Original PDF not reviewed by Recallfolio
Excessive condensation or water within the headlamp assembly caustion
Source components: ELECTRICAL SYSTEM:ADAS:BLINDSPOT:WARNING:LAMP.
Source record 10213430 at NHTSANHTSA communication ID: 10213326
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda guidelines for factory scheduled maintenance
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10213326 at NHTSANHTSA communication ID: 10105891
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.
Source components: SERVICE BRAKES.
Source record 10105891 at NHTSANHTSA communication ID: 10076682
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHITE MILKY STAINS ON INNER SURFACE OF HEADLIGHT LENS. SOME VEHICLES EQUIPPED WITH LED OR DISCHARGE TYPE HEADLIGHTS MAY EXHIBIT WHITE MILKY STAINS ON THE INNER SURFACE OF HEADLIGHT LENS. SOME CUSTOMERS MAY COMPLAIN OF POOR APPEARANCE. THIS CONCERN IS CAUSED BY GAS THAT EMITS FROM A GASKET IN THE LAMP UNIT. THE GAS ADHERES TO INNER SURFACEOF HEADLIGHT LENS AND REACTS WITH ANTI-CLOUDING COATING AND MOISTURE IN THE AIR TO CREATE WHITE MILKY STAINS. THE GASKET MATERIAL HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN. CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED USING THE FOLLOWING REPAIR PROCEDURE.
Source components: EQUIPMENT · EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10076682 at NHTSANHTSA communication ID: 10076647
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: SUSPENSION:FRONT:CONTROL ARM:LOWER ARM.
Source record 10076647 at NHTSANHTSA communication ID: 10213428
NHTSA source summary · Original PDF not reviewed by Recallfolio
Stains found on kpaint during PDI
Source components: STRUCTURE:BODY:DOOR.
Source record 10213428 at NHTSANHTSA communication ID: 10213427
NHTSA source summary · Original PDF not reviewed by Recallfolio
HandsFree bluetooth module and/or text messaging troubleshooting procedure
Source components: ELECTRICAL SYSTEM.
Source record 10213427 at NHTSANHTSA communication ID: 10213426
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various Elecfdtrical System Malfunction(s) Reflated to C15 Connector Corporation
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10213426 at NHTSANHTSA communication ID: 10076678
NHTSA source summary · Original PDF not reviewed by Recallfolio
STAINS FOUND ON PAINT DURING PDI SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEN PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED ARE TO REMOVE STAIN(S).
Source components: STRUCTURE.
Source record 10076678 at NHTSANHTSA communication ID: 10076677
NHTSA source summary · Original PDF not reviewed by Recallfolio
HANDS-FREE BLUETOOTH MODULE AND/OR TEXT MESSAGING TROUBLESHOOTING PROCEDURE. SOME VEHICLES MAY EXHIBIT BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THEHANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CREATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010. CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10076677 at NHTSANHTSA communication ID: 10076676
NHTSA source summary · Original PDF not reviewed by Recallfolio
VARIOUS ELECTRICAL SYSTEM MALFUNCTION(S) RELATEDTO C-15 CONNECTOR CORROSION. SOME VEHICLES MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING SYMPTOMS IN CONNECTION WITH A MALFUNCTION RELATED TO THE C-15 CONNECTOR. THE DRIVER SIDE POWER WINDOW DOES NOT OPERATE. THE DOOR DOES NOT OPEN WHEN USING THE ADVANCED KEYLESS SYSTEM. THE WARNING LAMP STAYS ON EVEN AFTER THE IGNITION SWITCH IS TURNED OFF. DTC B10E7:17 (START STOP UNIT, IG1 RELAY CIRCUIT MALFUNCTION) AND DTCS RELATED TO COMMUNICATION ERRORS MAY BE STORED IN PCM MEMORY.
Source components: ELECTRICAL SYSTEM.
Source record 10076676 at NHTSANHTSA communication ID: 10213333
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery test procedure requirements using the GR81291
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10213333 at NHTSANHTSA communication ID: 10213417
NHTSA source summary · Original PDF not reviewed by Recallfolio
Passenger fAirbag deactivation (PAD) indicator light illumination
Source components: AIR BAGS · EXTERIOR LIGHTING.
Source record 10213417 at NHTSANHTSA communication ID: 10213329
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Start /Stop Procedure with room fuse removed
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
Source record 10213329 at NHTSANHTSA communication ID: 10213424
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front power seats do not slide back and forth
Source components: POWER TRAIN · SEATS.
Source record 10213424 at NHTSANHTSA communication ID: 10076674
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRONT POWER SEATS DO NOT SLIDE BACK AND FORTH. SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. THIS CONCERN MAY BE CAUSED BY A FOREIGN OBJECT GETTING STUCK UNDER THE POWER SLIDE UNIT (BELOW) WHILE IN OPERATION. THIS CAN CAUSE MOTOR MOUNTING BRACKET (A) DEFORMATION, RESULTING IN MOTOR CABLE (B) BREAKAGE.
Source components: SEATS:FRONT ASSEMBLY:POWER ADJUST.
Source record 10076674 at NHTSANHTSA communication ID: 10076695
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-16 MX-5/MIATA CLUB AND LAUNCH EDITION - SERVICE PARTS INFORMATION. CERTAIN PARTS USED ON 2013-2016 MX-5/MIATA CLUB AND LAUNCH EDITIONS WERE ADDED BY MNAO'S PORT FACILITIES OR DEALERS AND ARE NOT SHOWN IN THE BEPC. REFER TO THE ILLUSTRATIONS BELOW TO ORDER SERVICE PARTS.
Source components: EQUIPMENT.
Source record 10076695 at NHTSANHTSA communication ID: 10213421
NHTSA source summary · Original PDF not reviewed by Recallfolio
Condensation/Fog in front and rear combination lights
Source components: EXTERIOR LIGHTING:FOG LIGHTS.
Source record 10213421 at NHTSANHTSA communication ID: 10213405
NHTSA source summary · Original PDF not reviewed by Recallfolio
ATFFZ required for SKYACTIV drive 6speed automatic transaxle
Source components: POWER TRAIN.
Source record 10213405 at NHTSANHTSA communication ID: 10100889
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE NEW SKYACTIV-DRIVE FW6A-EL AT USES AUTOMATIC TRANSMISSION FLUID (ATF) TYPE: FZ. ONLY USE ATF-FZ TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. IT IS A LOW VISCOSITY FORMULA WITH LESS FRICTION FOR BETTER FUEL ECONOMY. NOTE: ATF-FZ IS COLORED BLUE FOR EASY IDENTIFICATION. TO CHECK THE FLUID LEVEL, REMOVE THE BOLT, THEN REMOVE THE DIPSTICK. THE DIPSTICK IS MARKED WITH A FZ ON SKYACTIV-DRIVE FW6A-EL AT. WHEN FINISHED, INSERT THE DIPSTICK AND INSTALL THE BOLT.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10100889 at NHTSANHTSA communication ID: 10100888
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT (HEADLAMP/HEADLIGHT) OR REAR (TAILLAMP/TAIL-LIGHT) COMBINATION LIGHTS. THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMP-TOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.
Source components: EXTERIOR LIGHTING:HEADLIGHTS · EXTERIOR LIGHTING:TAIL LIGHTS.
Source record 10100888 at NHTSANHTSA communication ID: 10213325
NHTSA source summary · Original PDF not reviewed by Recallfolio
Special service tool shipment Janaurary 2016
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10213325 at NHTSANHTSA communication ID: 10105849
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN SUPPORT OF IMPROVED ELECTRICAL DIAGNOSIS ON SKYACTIV VEHICLES, MAZDA WILL SHIP A TERMINAL TEST KIT TO ALL DEALERS. THE TEST KIT IS DESIGNED PECIFICALLY FOR SKYACTIV MODULE TERMINALS. THE SST WILL BE SHIPPED BY MAZDAS TOOL VENDOR BOSCH STARTING JANUARY 15, 2016. PROCEDURES FOR USAGE ARE FOUND IN THE SKYACTIV WIRING TERMINAL TEST KIT WBT, COURSE #1649. THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST:
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10105849 at NHTSANHTSA communication ID: 10213393
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rattle/Chatter noise from rear differential
Source components: STRUCTURE · SUSPENSION.
Source record 10213393 at NHTSANHTSA communication ID: 10105859
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHILE DRIVING AT LOW SPEEDS, SOME VEHICLES MAY EXHIBIT A CHATTERING / RATTLING TYPE NOISE FROM THE REAR OF THE VEHICLE. THE NOISE MAY BE CAUSED BY A REAR DIFFERENTIAL BEARING FAILURE.
Source components: SUSPENSION:FRONT:WHEEL BEARING.
Source record 10105859 at NHTSANHTSA communication ID: 10076649
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT.
Source record 10076649 at NHTSANHTSA communication ID: 10105639
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
Source components: ENGINE.
Source record 10105639 at NHTSANHTSA communication ID: 10213378
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Oil seepage from engine oil pressure switch
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
Source record 10213378 at NHTSANHTSA communication ID: 10105646
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO: UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6) STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY) TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6) 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6) 3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY) 4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY) NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.
Source components: STEERING · SUSPENSION:FRONT:SHOCK ABSORBER.
Source record 10105646 at NHTSANHTSA communication ID: 10105644
NHTSA source summary · Original PDF not reviewed by Recallfolio
FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES.
Source components: ENGINE.
Source record 10105644 at NHTSANHTSA communication ID: 10076642
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: SUSPENSION:FRONT:SHOCK ABSORBER.
Source record 10076642 at NHTSANHTSA communication ID: 10213400
NHTSA source summary · Original PDF not reviewed by Recallfolio
20132014 CX5 Squeaking/Grinding noise from rear brakes
Source components: SERVICE BRAKES.
Source record 10213400 at NHTSANHTSA communication ID: 10105655
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A SQUEAKING / GRINDING NOISE FROM THE REAR BRAKES. THIS NOISE MAY BE CAUSED BY THE WEAR INDICATORS OF PREMATURELY WORN OUTER REAR BRAKE PADS. NOTE: THE INNER REAR BRAKE PADS WILL ONLY SHOW A LITTLE WEAR. THIS CONDITION ONLY AFFECTS THE OUTER REAR BRAKE PAD(S). DURING USAGE OF THE VEHICLE IN AREAS WHERE ROAD SALT IS USED, THE OUTER REAR BRAKE PAD(S) MAY BECOME STUCK DUE TO CORROSION. THIS MAY CAUSE BRAKE DRAGGING AND PREMATURE WEAR TO THE OUTER BRAKE PAD(S) ONLY. THE TREATMENT OF THE BRAKE PAD BACK PLATE HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
Source components: SERVICE BRAKES.
Source record 10105655 at NHTSANHTSA communication ID: 10076655
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: SERVICE BRAKES.
Source record 10076655 at NHTSANHTSA communication ID: 10213404
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Engine light and A/T Warning light on with one or more of these DTS (P0842, P0847, P0872, P0877, P0780, P1738) Stored in TCM Memory
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10213404 at NHTSANHTSA communication ID: 10105656
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10105656 at NHTSANHTSA communication ID: 10105621
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
Source record 10105621 at NHTSANHTSA communication ID: 10105624
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · SUSPENSION:FRONT:CONTROL ARM:LOWER ARM.
Source record 10105624 at NHTSANHTSA communication ID: 10076638
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: SUSPENSION:FRONT:CONTROL ARM:LOWER ARM.
Source record 10076638 at NHTSANHTSA communication ID: 10213407
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHINING NOISE FROM AUTOMATIC TRANSAXLE.
Source components: BACK OVER PREVENTION.
Source record 10213407 at NHTSANHTSA communication ID: 10076661
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: POWER TRAIN:AXLE ASSEMBLY.
Source record 10076661 at NHTSANHTSA communication ID: 10105629
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
Source record 10105629 at NHTSANHTSA communication ID: 10213436
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rattle/Pop noise from instkrument panel and/or creak noise from apillar over rough/bumpy roads
Source components: BACK OVER PREVENTION.
Source record 10213436 at NHTSANHTSA communication ID: 10105630
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHILE DRIVING OVER ROUGH OR BUMPY ROADS, SOME VEHICLES MAY EXHIBIT A RATTLE / POP NOISE FROM THE INSTRUMENT PANEL AND/OR A CREAK NOISE FROM THE A-PILLAR. RATTLE / POP NOISE FROM INSTRUMENT PANEL: THE RATTLE / POP NOISE MAY BE CAUSED BY LOW COWL PANEL (A) MOUNTING BOLT (B) TORQUE.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · STRUCTURE:BODY.
Source record 10105630 at NHTSANHTSA communication ID: 10076687
NHTSA source summary · Original PDF not reviewed by Recallfolio
RATTLE/POP NOISE FROM INSTRUMENT PANEL AND/OR CREAK NOISE FROM A-PILLAR OVER ROUGH/BUMPY ROADS. WHILE DRIVING OVER ROUGH OR BUMPY ROADS, SOME VEHICLES MAY EXHIBIT A RATTLE/POP NOISE FROM THE INSTRUMENT PANEL AND/OR A CREAK NOISE FROM THE A-PILLAR. THE RATTLE/POP NOISE MAY BE CAUSED BY A LOW COWL PANEL (A) MOUNTING BOLT (B) TORQUE.
Source components: EQUIPMENT · STRUCTURE · SUSPENSION.
Source record 10076687 at NHTSANHTSA communication ID: 10105634
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
Source components: ENGINE.
Source record 10105634 at NHTSANHTSA communication ID: 10213459
NHTSA source summary · Original PDF not reviewed by Recallfolio
20132014 CX5 Various electrical system malfunction(s) related to C15 Connector corrosion
Source components: ELECTRICAL SYSTEM.
Source record 10213459 at NHTSANHTSA communication ID: 10105517
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A SQUEAKING / GRINDING NOISE FROM THE REAR BRAKES. THIS NOISE MAY BE CAUSED BY THE WEAR INDICATORS OF PREMATURELY WORN OUTER REAR BRAKE PADS. NOTE: THE INNER REAR BRAKE PADS WILL ONLY SHOW A LITTLE WEAR. THIS CONDITION ONLY AFFECTS THE OUTER REAR BRAKE PAD(S). DURING USAGE OF THE VEHICLE IN AREAS WHERE ROAD SALT IS USED, THE OUTER REAR BRAKE PAD(S) MAY BECOME STUCK DUE TO CORROSION. THIS MAY CAUSE BRAKE DRAGGING AND REMATURE WEAR TO THE OUTER BRAKE PAD(S) ONLY.THE TREATMENT OF THE BRAKE PAD BACK PLATE HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
Source components: SERVICE BRAKES.
Source record 10105517 at NHTSANHTSA communication ID: 10105514
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING SYMPTOMS IN CONNECTION WITH A MALFUNCTION RELATED TO THE C-15 CONNECTOR. THE DRIVER SIDE POWER WINDOW DOES NOT OPERATE. THE DOOR DOES NOT OPEN WHEN USING THE ADVANCED KEYLESS SYSTEM. THE WARNING LAMP STAYS ON EVEN AFTER THE IGNITION SWITCH IS TURNED OFF. DTC B10E7:17 (START STOP UNIT, IG1 RELAY CIRCUIT MALFUNCTION) AND DTCS RELATED TO COMMUNICATION ERRORS MAY BE STORED IN PCM MEMORY. THE SYMPTOMS LISTED ABOVE MAY BE CAUSED BY CORROSION OF THE C-15 CONNECTOR TERMINALS DUE TO WATER INTRUSION THROUGH THE FRONT DOOR. IN LOW AMBIENT TEMPERATURES, THE DOOR HARNESS HARDENS. IF THE DOOR IS FULLY OPENED, IT MAY CREATE A GAP BETWEEN THE DOOR AND THE DOOR HARNESS GROMMET, WHICH MAY ALLOW WATER TO ENTER THROUGH THE GAP.MASS PRODUCTION CHANGES: THE FRONT DOOR HARNESS GROMMET HAS BEEN CHANGED TO IMPROVE SEALING PERFORMANCE. HOLES INSIDE THE FRONT PILLAR (WHICH ARE MADE FOR WEIGHT REDUCTION), HAVE BEEN COVERED TO PREVENT WATER INTRUSION.
Source components: ELECTRICAL SYSTEM.
Source record 10105514 at NHTSANHTSA communication ID: 10105523
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10105523 at NHTSANHTSA communication ID: 10105522
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE: THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION. THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT GETS STUCK WITH THE STEERING GEAR HOUSING. TO ELIMINATE THE NOISE, THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED.
Source components: STEERING.
Source record 10105522 at NHTSANHTSA communication ID: 10105520
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT RUST (A) ON THE LIFTGATE OPENING AROUND THE LEFT AND/OR RIGHT SIDE STOPPER (B). THE PAINT IN THIS AREA MAY BE THINNER THAN NORMAL DUE TO PRODUCTION VARIANCES. THE PRODUCTION PROCESS HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.
Source components: STRUCTURE:BODY:HATCHBACK/LIFTGATE.
Source record 10105520 at NHTSANHTSA communication ID: 10101457
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A GROAN TYPE NOISE FROM THE FRONT WHEEL HUB BEARING WHILE DRIVING AT HIGH SPEED OR WHEN CORNERING. THIS MAY BE CAUSED BY FRONT WHEEL HUB BEARING CORROSION.
Source components: WHEELS:HUB.
Source record 10101457 at NHTSANHTSA communication ID: 10101459
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10101459 at NHTSANHTSA communication ID: 10101466
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10101466 at NHTSANHTSA communication ID: 10105504
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. THIS CONCERN MAY BE CAUSED BY A FOREIGN OBJECT GETTING STUCK UNDER THE POWER SLIDE UNIT (BELOW) WHILE IN OPERATION. THIS CAN CAUSE MOTOR MOUNTING BRACKET (A) DEFORMATION, RESULTING IN MOTOR CABLE (B) BREAKAGE. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE MOTOR MOUNTING BRACKET (A) HAS BEEN MODIFIED TO INCREASE ITS STRENGTH.
Source components: EQUIPMENT:ELECTRICAL · SEATS:FRONT ASSEMBLY:POWER ADJUST.
Source record 10105504 at NHTSANHTSA communication ID: 10105462
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. IPOD ERROR MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10105462 at NHTSANHTSA communication ID: 10105465
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE: THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION. THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT GETS STUCK WITH THE STEERING GEAR HOUSING. TO ELIMINATE THE NOISE, THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED.
Source components: STEERING.
Source record 10105465 at NHTSANHTSA communication ID: 10105464
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A VIBRATION FROM THE DRIVER-SIDE POWER DOOR MIRROR GLASS WHEN THE VEHICLE IS DRIVEN AT HIGH SPEEDS. THIS CONCERN MAY BE DUE TO A LACK OF RIGIDITY OF THE MIRROR BASE SO THE MIRROR VIBRATES WHEN IT RECEIVES VEHICLE VIBRATION OR WIND PRESSURE. AN ADDITIONAL REINFORCEMENT HAS BEEN INSTALLED INSIDE THE DOOR TO INCREASE THE DOOR PANEL STRENGTH WHERE THE DOOR MIRROR IS MOUNTED. ALSO, THE DOOR MIRROR SHAPE HAS BEEN CHANGED. BOTH OF THESE MODIFICATIONS HAVE BEEN IMPLEMENTED TO ELIMINATE MIRROR GLASS VIBRATION CONCERNS.
Source components: STRUCTURE:BODY:DOOR · VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
Source record 10105464 at NHTSANHTSA communication ID: 10105481
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10105481 at NHTSANHTSA communication ID: 10105468
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMERS PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10105468 at NHTSANHTSA communication ID: 10105501
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. P2610:00: INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM P2507:00: PCM BATTERY VOLTAGE LOW INPUT AS A PAST MALFUNCTION, THE CUSTOMER WILL NOT NOTICE IT (NO WARNING LIGHT ILLUMINATED), BUT THE DTC MAY BE FOUND DURING A VEHICLE SERVICE. P2507 IN THIS SITUATION IS ONLY APPLICABLE ON 2016 AND LATER MODELS. THIS IS CAUSED BY THE ENGINE BEING STARTED 3 OR MORE TIMES AFTER A SHORT DURATION OF ENGINE OFF (LESS THAN 15 SECONDS) WITH THE ROOM FUSED REMOVED.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10105501 at NHTSANHTSA communication ID: 10105507
NHTSA source summary · Original PDF not reviewed by Recallfolio
ON SOME VEHICLES, THE FUEL FILLER LID WILL NOT OPEN/CLOSE. THIS MAY BE CAUSED BY SNOW WITH ROAD SALT BEING BROUGHT INTO THE FOOTWELL AREA. THE MELTED SALT WATER THEN FLOWS ALONG THE OPENER LEVER (A) AND ENTERS INTO THE CABLE (B) CAUSING THE INNER-CABLE TO CORRODE AND SEIZE. TO CORRECT THE PROBLEM, A FLANGE HAS BEEN ADDED TO THE FUEL FILLER LID OPENER LEVER (A) TO PREVENT WATER FROM FLOWING ALONG THE LEVER TO THE FUEL FILLER LID CABLE.
Source components: EQUIPMENT:MECHANICAL.
Source record 10105507 at NHTSANHTSA communication ID: 10105502
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITHOUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY). THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM THAT MAY DETECT FALSE ERROR OF THE A/F SENSOR, RESULTING IN FALSE DETECTION OF P0421. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED. CATALYST MONITOR FUNCTION EXPLANATION THE PCM MONITORS THE OXYGEN STORAGE AMOUNT PROPORTIONAL TO CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC. THE PCM STARTS TO MONITOR AFTER RECOVERY (FUEL INJECTION STARTS) FROM FUEL CUT CONTROL. THE PCM TEMPORARILY CHANGES THE TARGET AIR/FUEL RATIO TO RICH AT FUEL CUT RECOVERY, AND DETECTS THE RESPONSE TIME UNTIL THE HO2S OUTPUT SIGNAL OUTPUTS THE VOLTAGE ON THE RICH SIDE. IF THE CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC DETERIORATES, THE AMOUNT OF THE TIME UNTIL THE HO2S DETECTS THE VOLTAGE ON THE RICH SIDE IS SHORTER COMPARED TO THE NORMAL PURIFICATION CHARACTERISTIC AS SHOWN. THE PCM DETECTS A CATALYTIC CONVERTER MALFUNCTION USING THIS CHARACTERISTIC.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10105502 at NHTSANHTSA communication ID: 10099418
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE: THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION. THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT GETS STUCK WITH THE STEERING GEAR HOUSING. TO ELIMINATE THE NOISE, THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED.
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
Source record 10099418 at NHTSANHTSA communication ID: 10099417
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM. THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10099417 at NHTSANHTSA communication ID: 10099427
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. UNDER REPEATED STRESS, THE WIRE MAY BREAK CAUSING AN INOPERATIVE SEAT WARMER CONDITION.
Source components: SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
Source record 10099427 at NHTSANHTSA communication ID: 10099420
NHTSA source summary · Original PDF not reviewed by Recallfolio
FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES. ALL SKYACTIV ENGINES EQUIPPED WITH OIL PRESSURE SWITCH PART NUMBER PE01-18-501A ARE APPLICABLE TO THIS ISSUE.
Source components: ENGINE.
Source record 10099420 at NHTSANHTSA communication ID: 10099232
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT EITHER AN AUDIO SCREEN THAT IS LOCKING-UP (BLACK SCREEN) OR AN INOPERATIVE AUDIO TOUCH SCREEN. IN BOTH CASES HOWEVER, THE AUDIO UNIT SOUND OUTPUT IS NORMAL. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE AUDIO UNIT. THE PRODUCTION PROCESS AT THE AUDIO SUPPLIER HAS BEEN IMPROVED TO ELIMINATE THESE CONCERNS.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10099232 at NHTSA