Original record summaries, dates and identifiers for this model-year. Records 401–492 of 492, ordered newest first. Dated records on this page: Jun 1, 2020–May 11, 2023.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 11, 2023Service Bulletin/Repair Instructions
Bulletin
NHTSA communication ID: 10240001
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification 51A - Incorrect Grille Insert Color
NHTSA source summary · Original PDF not reviewed by Recallfolio
Restore Vehicle Configuration Customers may experience the following: ? Speed warning alert/Chime chimes continuously above a (80 KMPH) speed - instead of one time chime alert. This bulletin involves performing a restore vehicle configuration procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Heated Windshield Inoperative Customers may comment on the following: ? The heated windshield is inoperative. This bulletin involves inspecting and possibly connecting the heated windshield button to the windshield.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) or warning lamp illumination. Upon further investigation the technician may find that the multiple Diagnostic Trouble Codes (DTCs) have been set: ? C1403-29 - Transfer Case Range Position Sensor-Signal Invalid. ? C14AA-62 - Transfer Case Motor Position Sensor Supply-Signal Compare Failure. This bulletin involves reprogramming the DTCM with the latest software available.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Leak - Liftgate Glass to Swing Gate Water leak into rear cargo area at the bottom of lift glass seal and top of swing gate. This bulletin involves installing two pieces of foam pads.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PSU right intake camshaft Case 1) If you are to flash the PSU (Pentastar Upgrade Engine) PCM due to P0300 code presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ROCKER ARM ASSY - ROLLER ROCKER Case 1.- Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Ticking Noise Engine makes an abnormal ticking noise. There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ambient Air Temperature Missing, Malfunction Indicator Lamp (MIL) Lamp On, Diagnostic Trouble Code (DTC) P0070-15 Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P016F - Closed Loop Fuel Pressure Control At Limit - Pressure Too Low. ? P025C - Fuel Pump Module Control Circuit Low. ? P0300-00 - Multiple Cylinder Misfire. ? P0301-00 - Cylinder 1 Misfire. ? P0302-00 - Cylinder 2 Misfire. ? P0303-00 - Cylinder 3 Misfire. ? P0304-00 - Cylinder 4 Misfire. ? P0305-00 - Cylinder 5 Misfire. ? P0403-00 - EGR Control Circuit Open (Disabled Fault). ? P208B - Reductant Pump 1 Control Performance. Other Software enhancements: ? Low speed engine idle improvements. ? Improved engine restart performance and torque response during low fuel level and/or hot ambient conditions. This bulletin involves reprogramming the PCM with the latest available software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Missing Side Steps Vehicles ordered with side steps did not receive side steps installed. This bulletin involves installing missing side steps. NOTE: Vehicles were ordered with the side step option but did not get the side steps from the Factory.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P2B95 - Cold Start Injection Pulse Performance. This bulletin involves reprogramming the PCM with the latest available software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery Charge Indicator (BCI) Replacement Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC has been set: ? B1271-00 - Charge Level Indicator Internal. Customer may also experience the following: ? BCI does not indicate charge status while the vehicle is charging. This bulletin involves replacing the BCIM.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Axle Assembly Do not replace the Axle for Axle Locker Sensor failure. The parts kit (SENSOR KIT, Axle: 68544629A$) must be used to repair the Axle Locker Sensor on JL/JT equipped with the M210 and M220 Tru-Lok axles (DSE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating to QR40.12 Software Version Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating to QR40.12 Software Version Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Wheel Hub and Bearing Before replacing the front or rear wheel hub and bearing for moaning, grinding, or groaning type noise, verify the noise is not coming from the transfer case. Follow the diagnostic procedure outlined in SOL Publication S2303000001 prior to any repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FILTER KIT, Transmission Oil For leak concerns that have been isolated to a transmission pan gasket, please replace ONLY the gasket. Pan/filter replacement are not required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FILTER KIT, Transmission Oil For leak concerns that have been isolated to a transmission pan gasket, please replace ONLY the gasket. Pan/filter replacement are not required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ROCKER ARM ASSY - ROLLER ROCKER Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ROCKER ARM ASSY - ROLLER ROCKER Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ENGINE ASSY - 3.6L AUTO TRANS Before replacing the engine due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ENGINE ASSY - 3.6L AUTO TRANS Before replacing the engine due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Corrosion on Door, Hood And/or Swing Gate Hinges Corrosion found on the door, hood and/or swing gate hinge(s). This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim (Fig. 1) .Zinc Shim
NHTSA source summary · Original PDF not reviewed by Recallfolio
Corrosion on Door, Hood And/or Swing Gate Hinges Corrosion found on the door, hood and/or swing gate hinge(s). This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim (Fig. 1) .Zinc Shim
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Corrosion on Door hood Swing Gate Hinges Corrosion found on the door, hood and/or swing gate hinge(s). This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim. (Fig. 1) .Zinc Shim
NHTSA source summary · Original PDF not reviewed by Recallfolio
Corrosion on Door hood Swing Gate Hinges Corrosion found on the door, hood and/or swing gate hinge(s). This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim. (Fig. 1) .Zinc Shim
NHTSA source summary · Original PDF not reviewed by Recallfolio
Valve - Coolant JL PHEV Hoses to 3-Way valve coolant hoses misroute causes P0E80-00. Check hose routing as outlined in Star Online Publication S2208000205 or on a known good vehicle before replacing valve. Routing hoses correctly will likely fix the issue.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.
Source components: BACK OVER PREVENTION · EQUIPMENT:ELECTRICAL:INFOTAINMENT · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Integrated Dual Charging Module Before replacing the IDCM part please follow the appropriate service procedure for DTC P0D27, ensure to clear the codes and perform a charging test. If the codes come back again, proceed with the replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Sky One Power Top Rattle This bulletin involves checking the torque values on the Sky One-Touch power top screws andreplacing all 16 screws if one is found with an incorrect torque value. Customers may experience the following: A rattle noise over bumps and rough roads while driving coming from the roof area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.