2019 Jeep CHEROKEE
Manufacturer communications & TSBs.Page 1

03-002-26

NHTSA communication ID: 11035039

NHTSA source summary · Original PDF not reviewed by Recallfolio

Stop/Start Illuminated, 0x22 During Fork Wear Routine Technicians may experience the following: SYMPTOM: ● Negative response 0X22 after Recall 01C flash triggers one or more communication codes with controllers.

Source components: ELECTRICAL SYSTEM · ENGINE.

03-001-26

NHTSA communication ID: 11035038

NHTSA source summary · Original PDF not reviewed by Recallfolio

Unable to Complete 01C Recall Drive Cycle C14A7-97 Active Technicians may experience the following: SYMPTOM: ● After performing Recall 01C, the vehicle may get a 'Service AWD' message on the EVIC.

Source components: POWER TRAIN.

S2208000045 REV.D

NHTSA communication ID: 11034385

NHTSA source summary · Original PDF not reviewed by Recallfolio

Backup Camera Poor Image Quality Inspection

Source components: STRUCTURE:BODY.

S2523000003 REV.A

NHTSA communication ID: 11031688

NHTSA source summary · Original PDF not reviewed by Recallfolio

Door Latch, Handle And Ajar Additional Service Information.

Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.

08-075-26 REV. A

NHTSA communication ID: 11031423

NHTSA source summary · Original PDF not reviewed by Recallfolio

Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

Source components: ELECTRICAL SYSTEM.

21-027-26 REV. A

NHTSA communication ID: 11031328

NHTSA source summary · Original PDF not reviewed by Recallfolio

Two Speed Power Transfer Unit Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): ? C1494-07 - PTU Fork Position-Mechanincal Failures. Customers m

Source components: POWER TRAIN.

14082

NHTSA communication ID: 11031348

NHTSA source summary · Original PDF not reviewed by Recallfolio

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

Campaign / software reference: ID-26-22 Middle East & Africa

Source components: POWER TRAIN.

14081

NHTSA communication ID: 11031347

NHTSA source summary · Original PDF not reviewed by Recallfolio

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

Campaign / software reference: ID-26-20 APAC

Source components: POWER TRAIN.

14079

NHTSA communication ID: 11031346

NHTSA source summary · Original PDF not reviewed by Recallfolio

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

Campaign / software reference: ID-26-21

Source components: POWER TRAIN.

14078

NHTSA communication ID: 11031345

NHTSA source summary · Original PDF not reviewed by Recallfolio

(XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

Campaign / software reference: ID-26-21 Enlarged Europe

Source components: POWER TRAIN.

111447

NHTSA communication ID: 11031344

NHTSA source summary · Original PDF not reviewed by Recallfolio

ID-26-19 (XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

Campaign / software reference: ID-26-19

Source components: POWER TRAIN.

111432

NHTSA communication ID: 11031343

NHTSA source summary · Original PDF not reviewed by Recallfolio

D-26-10 (XX1) Two Speed Power Transfer Unit (PTU) - Select 2017 - 2019 Jeep Cherokee (KL)

Campaign / software reference: D-26-10

Source components: POWER TRAIN.

21-027-26

NHTSA communication ID: 11031327

NHTSA source summary · Original PDF not reviewed by Recallfolio

Two Speed Power Transfer Unit Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): ? C1494-07 - PTU Fork Position-Mechanincal Failures. Customers m

Source components: POWER TRAIN.

18-044-26

NHTSA communication ID: 11030229

NHTSA source summary · Original PDF not reviewed by Recallfolio

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi

Source components: ENGINE.

S2208000045 REV.C

NHTSA communication ID: 11030269

NHTSA source summary · Original PDF not reviewed by Recallfolio

Backup Camera Poor Image Quality Inspection

Source components: UNKNOWN OR OTHER.

S1408000384 REV.J

NHTSA communication ID: 11030035

NHTSA source summary · Original PDF not reviewed by Recallfolio

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Source components: ELECTRICAL SYSTEM.

08-075-26

NHTSA communication ID: 11029670

NHTSA source summary · Original PDF not reviewed by Recallfolio

Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.

S1408000384 REV.I

NHTSA communication ID: 11028904

NHTSA source summary · Original PDF not reviewed by Recallfolio

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Source components: ELECTRICAL SYSTEM.

S1721000016 REV.B

NHTSA communication ID: 11026812

NHTSA source summary · Original PDF not reviewed by Recallfolio

Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked.

Source components: POWER TRAIN.

9100736

NHTSA communication ID: 11026652

NHTSA source summary · Original PDF not reviewed by Recallfolio

Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Source components: ELECTRICAL SYSTEM.

S1805000006 REV.B

NHTSA communication ID: 11025508

NHTSA source summary · Original PDF not reviewed by Recallfolio

ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

Source components: SERVICE BRAKES.

9100325 Rev 1

NHTSA communication ID: 11024035

NHTSA source summary · Original PDF not reviewed by Recallfolio

Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.

Source components: ENGINE.

23-008-25 REV. A

NHTSA communication ID: 11023326

NHTSA source summary · Original PDF not reviewed by Recallfolio

Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

Source components: STRUCTURE:BODY.

02-002-25 REV. A

NHTSA communication ID: 11023168

NHTSA source summary · Original PDF not reviewed by Recallfolio

Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.

Source components: SUSPENSION.

31-001-25 REV. B

NHTSA communication ID: 11022011

NHTSA source summary · Original PDF not reviewed by Recallfolio

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

Source components: STRUCTURE:BODY.

9100653

NHTSA communication ID: 11022027

NHTSA source summary · Original PDF not reviewed by Recallfolio

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Source components: UNKNOWN OR OTHER.

9100645

NHTSA communication ID: 11022026

NHTSA source summary · Original PDF not reviewed by Recallfolio

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Source components: UNKNOWN OR OTHER.

31-001-25 REV. A

NHTSA communication ID: 11022012

NHTSA source summary · Original PDF not reviewed by Recallfolio

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

Source components: STRUCTURE:BODY.

31-001-25

NHTSA communication ID: 11022003

NHTSA source summary · Original PDF not reviewed by Recallfolio

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

Source components: STRUCTURE:BODY.

08-220-25

NHTSA communication ID: 11021010

NHTSA source summary · Original PDF not reviewed by Recallfolio

Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

Source components: STRUCTURE:BODY.

S2208000138 REV.B

NHTSA communication ID: 11020600

NHTSA source summary · Original PDF not reviewed by Recallfolio

Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed

Source components: ELECTRICAL SYSTEM.

S2323000002 REV.A

NHTSA communication ID: 11018447

NHTSA source summary · Original PDF not reviewed by Recallfolio

"Washer Light On And Will Not Turn Off After Adding Washer Solvent."

Source components: ELECTRICAL SYSTEM.

9100471

NHTSA communication ID: 11015810

NHTSA source summary · Original PDF not reviewed by Recallfolio

"CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Source components: UNKNOWN OR OTHER.

23-008-25

NHTSA communication ID: 11014385

NHTSA source summary · Original PDF not reviewed by Recallfolio

"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. "

Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.

102934

NHTSA communication ID: 11013643

NHTSA source summary · Original PDF not reviewed by Recallfolio

THROTTLE BODY

Source components: ENGINE.

S1408000384 REV.H

NHTSA communication ID: 11013171

NHTSA source summary · Original PDF not reviewed by Recallfolio

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Source components: ELECTRICAL SYSTEM.

S2523000003

NHTSA communication ID: 11012884

NHTSA source summary · Original PDF not reviewed by Recallfolio

Door Latch, Handle And Ajar Additional Service Information.

Source components: STRUCTURE:BODY.

S1408000384 REV.G

NHTSA communication ID: 11012777

NHTSA source summary · Original PDF not reviewed by Recallfolio

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Source components: ELECTRICAL SYSTEM.

9100468

NHTSA communication ID: 11012010

NHTSA source summary · Original PDF not reviewed by Recallfolio

FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

Source components: UNKNOWN OR OTHER.

9100445

NHTSA communication ID: 11011799

NHTSA source summary · Original PDF not reviewed by Recallfolio

Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369691AD) is the proper repair.

Source components: ELECTRICAL SYSTEM.

S2208000045 REV.B

NHTSA communication ID: 11011774

NHTSA source summary · Original PDF not reviewed by Recallfolio

Backup Camera Poor Image Quality Inspection

Source components: BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING.

S228A000017 REV.A

NHTSA communication ID: 11007954

NHTSA source summary · Original PDF not reviewed by Recallfolio

Battery Drain Suspected or "Identified" From USB or Media Hub

Source components: ELECTRICAL SYSTEM.

09-018-24

NHTSA communication ID: 11006983

NHTSA source summary · Original PDF not reviewed by Recallfolio

"2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block."

Source components: ENGINE.

23-004-24 REV. A

NHTSA communication ID: 11006241

NHTSA source summary · Original PDF not reviewed by Recallfolio

"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses."

Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.

31-001-24

NHTSA communication ID: 11005320

NHTSA source summary · Original PDF not reviewed by Recallfolio

"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

Source components: STRUCTURE:BODY.

08-153-24

NHTSA communication ID: 11002805

NHTSA source summary · Original PDF not reviewed by Recallfolio

"Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing."

Source components: STRUCTURE:BODY.

S1408000384 REV.F

NHTSA communication ID: 11002828

NHTSA source summary · Original PDF not reviewed by Recallfolio

"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Source components: ELECTRICAL SYSTEM · ENGINE.

97892

NHTSA communication ID: 11000172

NHTSA source summary · Original PDF not reviewed by Recallfolio

SWITCH - BRAKE

Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.

2300424

NHTSA communication ID: 10251854

NHTSA source summary · Original PDF not reviewed by Recallfolio

Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.

Source components: EXTERIOR LIGHTING:HEADLIGHTS.

S248A000001

NHTSA communication ID: 10251785

NHTSA source summary · Original PDF not reviewed by Recallfolio

SOS and Assistance Call Not Working After Radio Exchange Unit Installed

Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..

S1408000384

NHTSA communication ID: 10251783

NHTSA source summary · Original PDF not reviewed by Recallfolio

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.

S1721000016

NHTSA communication ID: 10247452

NHTSA source summary · Original PDF not reviewed by Recallfolio

Service 4wd Light On, AWD System Service Required Message Illuminated. Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked, Set.

Source components: AIR BAGS · ENGINE AND ENGINE COOLING.

9100229

NHTSA communication ID: 10244356

NHTSA source summary · Original PDF not reviewed by Recallfolio

LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.

Source components: SUSPENSION.

9100226

NHTSA communication ID: 10248509

NHTSA source summary · Original PDF not reviewed by Recallfolio

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Source components: ELECTRICAL SYSTEM.

9004542

NHTSA communication ID: 10248508

NHTSA source summary · Original PDF not reviewed by Recallfolio

Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.

Source components: VISIBILITY:WINDSHIELD WIPER/WASHER.

9100226

NHTSA communication ID: 10244348

NHTSA source summary · Original PDF not reviewed by Recallfolio

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Source components: ELECTRICAL SYSTEM:WIRING.

9004542

NHTSA communication ID: 10244347

NHTSA source summary · Original PDF not reviewed by Recallfolio

Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.

Source components: VISIBILITY:WINDSHIELD WIPER/WASHER.

93120

NHTSA communication ID: 10243209

NHTSA source summary · Original PDF not reviewed by Recallfolio

FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

93023

NHTSA communication ID: 10243208

NHTSA source summary · Original PDF not reviewed by Recallfolio

Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

S2108000093

NHTSA communication ID: 10243153

NHTSA source summary · Original PDF not reviewed by Recallfolio

Apple CarPlay Does Not Work Or Not Connecting

Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.

ZD7

NHTSA communication ID: 10242779

NHTSA source summary · Original PDF not reviewed by Recallfolio

Customer Satisfaction Notification ZD7 - Radio Software update

Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..

9100196

NHTSA communication ID: 10242717

NHTSA source summary · Original PDF not reviewed by Recallfolio

Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

ReferenceZD7

NHTSA communication ID: 10241056

NHTSA source summary · Original PDF not reviewed by Recallfolio

Customer Satisfaction Notification ZD7 - Radio Software Update

Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..

BulletinA

NHTSA communication ID: 10240002

NHTSA source summary · Original PDF not reviewed by Recallfolio

Customer Satisfaction Notification ZD7 - Radio Software Update

Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..

1806523

NHTSA communication ID: 10239969

NHTSA source summary · Original PDF not reviewed by Recallfolio

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software.

Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).

S238A000024

NHTSA communication ID: 10240004

NHTSA source summary · Original PDF not reviewed by Recallfolio

SOS, Assistance Calls Not Successful After Radio Replacement or Radio Software Update

Source components: EQUIPMENT:ELECTRICAL:INFOTAINMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.

0700723

NHTSA communication ID: 10239957

NHTSA source summary · Original PDF not reviewed by Recallfolio

Water Quality When Mixed With Engine Coolant

Source components: ENGINE AND ENGINE COOLING.

0811223

NHTSA communication ID: 10236957

NHTSA source summary · Original PDF not reviewed by Recallfolio

Rear Tail Lamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). This bulletin is to communicate the procedure for rear tail lamp condensation clearing.

Source components: EXTERIOR LIGHTING · EXTERIOR LIGHTING:TAIL LIGHTS.

9100142

NHTSA communication ID: 10236969

NHTSA source summary · Original PDF not reviewed by Recallfolio

Mirror

Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES.

1804823

NHTSA communication ID: 10236933

NHTSA source summary · Original PDF not reviewed by Recallfolio

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.

0900323

NHTSA communication ID: 10236928

NHTSA source summary · Original PDF not reviewed by Recallfolio

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ? Oil pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

Source components: ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION · UNKNOWN OR OTHER.

9003357A

NHTSA communication ID: 10247906

NHTSA source summary · Original PDF not reviewed by Recallfolio

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Source components: ENGINE AND ENGINE COOLING.

9003357a

NHTSA communication ID: 10234379

NHTSA source summary · Original PDF not reviewed by Recallfolio

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Source components: ENGINE AND ENGINE COOLING.

S228A000028

NHTSA communication ID: 10234424

NHTSA source summary · Original PDF not reviewed by Recallfolio

Radio Remained On After Ignition Is Switched Off, Dead Battery From Excessive Radio Current Draw

Source components: ELECTRICAL SYSTEM.

9003357

NHTSA communication ID: 10247905

NHTSA source summary · Original PDF not reviewed by Recallfolio

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Source components: BACK OVER PREVENTION.

S1408000384

NHTSA communication ID: 10234420

NHTSA source summary · Original PDF not reviewed by Recallfolio

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Source components: ELECTRICAL SYSTEM.

9003357

NHTSA communication ID: 10234378

NHTSA source summary · Original PDF not reviewed by Recallfolio

ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Source components: ENGINE AND ENGINE COOLING.

3100123

NHTSA communication ID: 10247995

NHTSA source summary · Original PDF not reviewed by Recallfolio

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Source components: STRUCTURE.

3100123

NHTSA communication ID: 10234468

NHTSA source summary · Original PDF not reviewed by Recallfolio

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Source components: STRUCTURE.

08-038-23

NHTSA communication ID: 10231815

NHTSA source summary · Original PDF not reviewed by Recallfolio

Radio Over The Air JR34.3 Updating to JR34.32.Software Version Customers may experience one or more of the following: Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.

Source components: BACK OVER PREVENTION:SOFTWARE.

S2308000009

NHTSA communication ID: 10231745

NHTSA source summary · Original PDF not reviewed by Recallfolio

Electric Power Steering (EPS) Will Not Calibrate, Negative Response Error Code 0X10

Source components: POWER TRAIN · STEERING.

09-003-23

NHTSA communication ID: 10231800

NHTSA source summary · Original PDF not reviewed by Recallfolio

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: Oil pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

Source components: EXTERIOR LIGHTING · SERVICE BRAKES.

88806

NHTSA communication ID: 10231750

NHTSA source summary · Original PDF not reviewed by Recallfolio

Warranty Bulletin D-23-01 - (XB1) 2.4L Engine ? Select 2014 - 2019 Jeep Cherokee (KL), 2017 - 2018 Jeep Compass (MP), 2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

S2323000002

NHTSA communication ID: 10231711

NHTSA source summary · Original PDF not reviewed by Recallfolio

Washer Light On And Will Not Turn Off After Adding Washer Solvent.

Source components: EQUIPMENT:ELECTRICAL.

S2218000023

NHTSA communication ID: 10229769

NHTSA source summary · Original PDF not reviewed by Recallfolio

Malfunction Indicator Lamp (MIL) Illuminated. Diagnostic Trouble Code (DTC) U02A3 ? Lost Communication ith Particulate Matter (PM) Sensor, Set After PM Sensor Replacement.

Source components: BACK OVER PREVENTION · EXTERIOR LIGHTING.

08-003-22 REV. A

NHTSA communication ID: 10229816

NHTSA source summary · Original PDF not reviewed by Recallfolio

UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

Source components: BACK OVER PREVENTION · EQUIPMENT:ELECTRICAL:INFOTAINMENT · STEERING.

31-002-22

NHTSA communication ID: 10229810

NHTSA source summary · Original PDF not reviewed by Recallfolio

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Source components: STRUCTURE.

08-229-22

NHTSA communication ID: 10229805

NHTSA source summary · Original PDF not reviewed by Recallfolio

Radio Over The Air Software Version Update to 22.66 This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from IR22.64 and IR22.65 to IR22.66. The national launch for the FOTA is expected to begin on January 09, 2023. ? Wi-Fi hotspot connection not working. ? No internet connection message on the phone when trying to connect to a device

Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..

09-013-22

NHTSA communication ID: 10229804

NHTSA source summary · Original PDF not reviewed by Recallfolio

2.4L Engine Oil Consumption Test The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

Source components: ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION: OIL COOLER.

S2008000131 Rev.

NHTSA communication ID: 10229743

NHTSA source summary · Original PDF not reviewed by Recallfolio

U11E9 Lost Communication with AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated

Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.

18-161-22

NHTSA communication ID: 10229791

NHTSA source summary · Original PDF not reviewed by Recallfolio

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. P2C90 - Crankcase Ventilation System - Hose "A" Disconnected. P1D73 - AGS performance fault. P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(Enlarged Europe and Middle East/Africa) only equipped with Gas ParticulateFilter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included: AGS stuck condition (The customer won't see an issue, but this calibrationallows AGS performance fault - P1D73, to work correctly). Software corrects an issue with the wrong cylinder identification if an injectorcircuit performance fault is set in the PCM: If any of the series of injector control circuit faults are set, please refer tothe bullet-pointed list below to determine which injector to address.

Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE · VEHICLE SPEED CONTROL.

0821422

NHTSA communication ID: 10230541

NHTSA source summary · Original PDF not reviewed by Recallfolio

Radio Over The Air Updates to JR34.3/JR34.4 and JR34.41

Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..

S228A000028

NHTSA communication ID: 10227721

NHTSA source summary · Original PDF not reviewed by Recallfolio

Radio Remained On After Ignition Is Switched Off, Dead Battery from Excessive Radio Current Draw

Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..

S1823000031

NHTSA communication ID: 10225989

NHTSA source summary · Original PDF not reviewed by Recallfolio

Flat Tow Or Recreational Towing KL Cherokee

Source components: EQUIPMENT.

3100122

NHTSA communication ID: 10229572

NHTSA source summary · Original PDF not reviewed by Recallfolio

Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Source components: STRUCTURE.

3100122

NHTSA communication ID: 10225424

NHTSA source summary · Original PDF not reviewed by Recallfolio

Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Source components: STRUCTURE.

3100122

NHTSA communication ID: 10225287

NHTSA source summary · Original PDF not reviewed by Recallfolio

Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.

S228A000017

NHTSA communication ID: 10229479

NHTSA source summary · Original PDF not reviewed by Recallfolio

Battery Drain Suspected or "Identified" From USB or Media Hub

Source components: ELECTRICAL SYSTEM.

S228A000017

NHTSA communication ID: 10225342

NHTSA source summary · Original PDF not reviewed by Recallfolio

Battery Drain Suspected or "Identified" From USB or Media Hub

Source components: ELECTRICAL SYSTEM.

S228A000017

NHTSA communication ID: 10225205

NHTSA source summary · Original PDF not reviewed by Recallfolio

Battery Drain Suspected or "Identified" From USB or Media Hub

Source components: ELECTRICAL SYSTEM.