2009 Chevrolet SILVERADO Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 277, ordered newest first. Dated records on this page: Jun 1, 2011–Oct 16, 2013.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 16, 2013Service Bulletin/Repair Instructions
PIT4816E
NHTSA communication ID: 10112413
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have multiple electrical concerns and or intermittent no crank. Technician will need to remove the 175 amp Mega Fuse and inspect for arcing. If any type of arcing is found replace the affected components. Technician will also check the voltage drop on the positive and negative and the torque of the cable at the starter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have various 2-Mode Hybrid issues. Some vehicle may have service hybrid system lamp that comes on with a Diagnostic Trouble Code P061B set. Technician will need to take a snap shot of the Electronic Brake Control Module and call General Motors Technical Assistance Center for further assistance. Some vehicles may have a combination of engine stall at a stop, lacks power on acceleration, surge while driving, engine flare, transmission slip, poor or lower fuel economy or reduced EV range/limited electric propulsion since completion of recent programming. Technician will need to perform a Charge Procedure. Some vehicles have Diagnostic Trouble Code P0BBD stored without Diagnostic Trouble Code P061B or P0AFA. Technician will verify that the Drive Motor Battery was not run low on charge due to a no start concern.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Technician may find Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723. Technician should follow published Service Information diagnostics for Diagnostic Trouble Code P0701 first. Technician will also ensure the fluid level is at the top of the hot band when the transmission fluid temperature is 175° Fahrenheit. Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723 can set by the following fluid service/filter change, transmission service involving removing the pan, low fluid level caused by leaks, or after long periods of storage. If the fluid level has been properly checked using the HOT check procedure listed in Service Information document 2408059 and any of the Diagnostic Trouble Codes reset during a cold start inspect the internal suction filter for possible cracks. If no other concerns are found inspect for a stuck lube regulator valve in the pump cover due to debris.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the percentage of UV protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces UV rays down to 4% or less. Front side door glass reduces UV rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: DELAYED OR NO DRIVE AND DELAYED OR NO REVERSE WITH DTC'S, RANGE INHIBIT. MODEL YEARS 2001-2013. *PE UPDATED ON 06/08/2011. *KB UPDATED ON 06/16/2011. *KB UPDATED 11/26/12. *PE UPDATED 12/4/2013 *JS
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/CADILLAC/GMC: HYBRID DRIVEABILITY OR CUSTOMER CONCERNS OF FLARE, SLIP, STALL AT A STOP, SURGE, LACK OF POWER, POOR FUEL ECONOMY, REDUCED EV RANGE/LIMITED ELECTRIC PROPULSION, DTC P061B AFTER CAMPAIGN 09102B OR DTC P061B PRIOR TO CAMPAIGN. *PE UPDATED 3/14/11. *PE UPDATED 12/4/2013 *JS
Source components: ENGINE AND ENGINE COOLING:ENGINE · FUEL SYSTEM, GASOLINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the new fluids available for axle service and clarifies usage. Technician will use the chart to determine the proper axle lubricant to use.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/PONTIAC/ SATURN: THERE IS FLUID LEAKING FROM POWER STEERING SYSTEM, ALONG A FLUID LEAK IN FRONT OF VEHICLE UNDERNEATH AND SHOULD BE INSPECTED, CLEANED AND IDENTIFIED BEFORE REPAIRING OR REPLACING. MODEL 2010-14 LACROSSE, 2011-14 REGAL, 2007-14 ESCALADE, SUBURBAN, TAHOE, YUKON, YUKON XL, YUKON DENALI, YUKON DENALI XL, 2013-14 XTS, 2005-14 MALIBU, 2007-13 AVALANCHE, SILVERADO, SIERRA, 2006-10 G6, 2007-09 AURA. *PE
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on GM of Canada New Vehicle Limited Warranty Tire Program and Global Warranty Management (GWM) Submission Information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:APPLIANCE:AIR CONDITIONER · EQUIPMENT:ELECTRICAL · POWER TRAIN:AXLE ASSEMBLY · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about an owner that may request to have a different style mirror installed on their vehicle or request a different mirror before they purchase the vehicle. Swapping mirrors on vehicles equipped with Side Blind Zone Alert, Regular Production Option Code UFT, is not recommended. On other vehicles tech will need to verify if the vehicle is equipped with door modules or not. On vehicles with door modules technician will need to contact Techline Customer Support for new calibrations for both doors. On vehicles not equipped with door modules no calibrations are needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. ALL 2014 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: LOW ENGINE OIL PRESSURE, NO OIL PRESSURE, AND/OR ENGINE NOISE. THIS COULD BE THE RESULT OF A STICKING OIL PUMP PRESSURE RELIEF VALVE. *KB
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Technician will need to use a scan tool to verify that the alarm was activated by the inclination sensor. If the trigger is the inclination sensor, inspect the sensor's mounting location. Technician will need to relocate the sensor if it is attached to the driver's side lower Heater-Vent-Air Conditioning duct. Technician will need to reinstall the sensor to the top of the Body Control Module bracket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a cold engine tick noise for 50 seconds at start up. Technician determines if the tick noise is possibly coming from the exhaust manifold, as this noise could easily be mistaken for an engine tick noise. If your SI diagnosis does not isolate the cause of this concern, this concern should be considered a vehicle design characteristic of the ECM calibration and no additional repairs should be performed.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC: HYDRAULIC POWER STEERING LEAK AT HOSE CONNECTION TO STEERING RACK. ALL POTENTIAL LEAKS SHOULD BE COMPLETELY CLEANED AND INDENTIFIED BEFORE ATTEMPTING TO REPAIR OR REPLACE ANY POWER STEERING COMPONENTS. *JS UPDATED 4/22/13. *PE
Source components: STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a cold air leak on the front passenger side while driving. Technician will need to use black RTV silicone and apply over the seam between the upper and lower Heater-Vent-Air Conditioning case halves.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that during the Pre-Delivery Inspection it may be noticed that the backup alarm is inoperative. Technician can locate the wire harness on the right rear of the frame. Technician can route the harness up and over the spare tire hoist tube and connect to the backup alarm.
Source components: BACK OVER PREVENTION: BACK-UP ALARM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a service 4WD message displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code C0379. Technician will need to inspect the front axle actuator connector for signs of moisture intrusion. If there is corrosion on the terminals at either location replace the actuator and harness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 miles per hour at any given speed when looking straight at the needle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have misfires on cylinders 1, 4, 6 and 7. Technician should inspect the camshaft part numbers. Technician should ensure to use part number for the application by using the numbers stamped on the cam.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a rough idle and/or momentary lack of power after cold starting the engine and immediately placing the transmission in gear. Technician should follow published Service Information diagnostics first. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: ELECTRICAL SYSTEM:IGNITION · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: AFTER COLD STARTING ENGINE AND PLACING IN GEAR, WOULD HAVE A ROUGH IDLE AND/LACK OF POWER, MOMENTARILY BEFORE STARTUP A FEW MINUTES LATER. MODELS 2009-2013 EXPRESS, SILVERADO, SUBURBAN, SAVANA, SIERRA. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a compass that's not accurate or slow to update. Technician should check for a magnetic base roof mounted accessory interfering with the compass module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that 2ML70 Transmission Assembly will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the puddle light operation. Technician should be advised that the puddle lamps to operate, "Approach Lighting" must be turned on using the Drivers Information Center buttons.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B1517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine.
Source components: ELECTRICAL SYSTEM:IGNITION · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC: ORIGINAL STYLE BLOWER MOTOR ASSEMBLY IS NO LONGER AVAILABLE. A REVISED HVAC BLOWER MOTOR ASSEMBLY FOR FULL SIZE TRUCKS IS REQUIRED, WITH MODIFICATIONS, TO FUNCTION PROPERLY. *PE UPDATED 2/25/13. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have windows inoperative while the engine is running but work when the engine is off. Technician should look for aftermarket parts and remove them and retest the windows before any in depth diagnostics are performed.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube box/hitch, etc. to the rear of the truck, which affects the rear park assist operation. Technician can disable the rear park assist for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a rattle, buzz, tick, or vibration type noise that appears to be coming from the center of the dash. Technician will adjust the transmission dipstick tube away from the front of cowl to provide additional clearance.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise during light acceleration around 1200-2000 Revolutions per minute. Technician will need to reposition the fuel line and bracket down away from the floor pan.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a no crank condition after the vehicle has had very low accessory battery voltage or a dead battery condition. Technician may find Diagnostic Trouble Code P0C76 set. Technician should be advised that anytime a battery charger or booster pack is connected to the 12 volt battery, the ignition key should always be in the off position. If a battery charger or booster pack is connected to the 12 volt battery with the ignition key on tech will need to reset the Hybrid Powertrain Control Module Diagnostic Trouble Codes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Electronic Brake Control Module and Brake Pressure Modulator Valve for the 2-Mode Hybrid Utilities and Trucks will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a lack of brake assist after disconnecting the battery or after the 12 volts battery has run low on voltage. The Antilock Braking System Malfunction Indicator Lamp may also be on. Technician may find Diagnostic Trouble Code C121D sym 00 or C056D sym 00 set in the Electronic Brake Control Module. Technician should be advised to wait for a period of at least 1 minute with the ignition in the "OFF" position prior to disconnecting the negative battery cable. Technician will need to follow these steps to repair the concern. 1. Install the negative battery cable to the battery. 2. Rotate the lever lock clockwise until an audible click is heard in order to connect the negative battery cable to the battery. 3. Position the negative battery cable insulating cover over the negative terminal. 4. Start the vehicle without stepping on the brake pedal. 5. Shut the vehicle "Off" for one minute. 6. Restart vehicle and check brakes for proper operation. 7. Clear codes in the Engine Control Module and the Electronic Brake Control Module.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, ELECTRIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about Electronic Brake Control Module relearn procedure is required anytime the Electronic Brake Control Module is replaced or has been Service Programming System reprogrammed.
Source components: EQUIPMENT:ELECTRICAL · SERVICE BRAKES, ELECTRIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional vehicle speed sensor diagnostic information. Technician may encounter multiple issues when diagnosing a Vehicle Speed Sensor. Technician will find it difficult to follow the speed signal path between the components. To test connect the Fluke meter leads between circuits 821 and 822 and set the meter to Alternating current voltage and then press the hertz button. When the Engine Control Module showing correct miles per hour in the data list however it is setting a Diagnostic Trouble Code for the Vehicle Speed Sensor. To test connect the Fluke meter red lead to circuit 6399 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. The Instrument Panel Cluster speedo will work correctly when the Engine Control Module or Antilock Braking System Diagnostic Trouble Codes are for the Vehicle Speed Sensor. To test connect the Fluke meter red lead to circuit 1827 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. When the Antilock Braking System Malfunction Indicator Lamp on with Electronic Brake Control Module Diagnostic Trouble Code C0055 and no other customer complaints, to test connect the Fluke meter red lead to circuit 817 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an Antilock Braking System lamp followed by a Service Stability message in the Drivers Information Center. Technician my find Diagnostic Trouble Code C0710 set in the Electronic Brake Control Module. Technician may or may not find Diagnostic Trouble Code C0455. Technician will need to ensure the steering wheel is properly installed to the steering shaft.
Source components: SERVICE BRAKES, AIR:ANTILOCK · SERVICE BRAKES, ELECTRIC · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B0081 in the Sensing and Diagnostic Module and Passenger Presence Sensor modules. Technician should inspect the Sensing and Diagnostic Module and Passenger Presence Sensor powers, grounds, and communication circuits at all in line connectors for fully seated, backed out terminals, and proper terminal tension using the correct test probes.
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE · AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B0081 in the Sensing and Diagnostic Module and Passenger Presence Sensor modules. Technician should inspect the Sensing and Diagnostic Module and Passenger Presence Sensor powers, grounds, and communication circuits at all in line connectors for fully seated, backed out terminals, and proper terminal tension using the correct test probes.
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE · AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about hairline cracks may be noticed in the pad friction material, when performing a brake inspection. Technician should be advised that the hairline cracks do not affect the operation of the brake system and the pads should not be replaced if only hairline cracks are found.
Source components: SERVICE BRAKES · SERVICE BRAKES, AIR:DISC:PADS · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: DIAGNOSE AND REPAIR HVAC BLOWER FUNCTION. MAY NOT BE ANY AIR FLOW FROM THE HVAC VENTS. ONE POSSIBLE OF THIS CONDITION MAY BE THE CONTACTS IN THE HVAC JUNCTION BLOCK(S) LOCATED AT THE RIGHT SIDE OF THE INSTRUMENTAL PANEL. *JS UPDATED 1/24/13. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a "Service Stability Message" appears on the Drivers Information Center. Technician will find Diagnostic Trouble Code C0561 set in the Electronic Brake Control Module. Technician will need to address any other Diagnostic Trouble Codes that are set in the vehicle first before working on Diagnostic Trouble Code C0561.
Source components: EQUIPMENT:ELECTRICAL · SERVICE BRAKES, ELECTRIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the content theft alarm is inoperative. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. Technician should be advised that the vehicle must have Keyless Entry Regular Production Option Code (AU0/AU3) and Regular Production Option Code YE9 or Y91 to be equipped with content theft alarm.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have grease leaking from front hub bearings. Technician should not replace the bearing for grease purge. Technician should be advised to not clean the purged grease from the area immediately on or adjacent to the seals because this grease provides additional protection. Technician should only replace the bearing if the seals show visible damage, bearing endplay is greater than 0.005" or 0.13mm, bearing exhibits rough rotation, or bearing exhibits abnormal noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that has a squawk or grunt type noise when shifting from 2nd to 3rd gear. Technician should replace the 3-4 clutch Friction and Steel Clutch Plates along with the Apply Plate and Selective Backing Plate.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to set a personalized easy exit seat and/or power tilt column position and they will only move a predetermined amount. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have passenger window express down feature is inoperative. Technician should be advised that models equipped with either Memory Seats Regular Production Option Code (AN3) and/or Power Folding Mirrors Regular Production Option Code (DL3) will have the passenger window express down feature. Dealer should advised the customer if the vehicle does not have one of the Regular Production Option Codes AN3 and or DL3, this is a normal operating characteristic.
Source components: EQUIPMENT:ELECTRICAL · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that if the ignition key is turned to the start position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. Some customers may state that this feature is inoperative. Technician should be advised that if the Low Fuel warning lamp is on and/or the FUEL LEVEL LOW message is displayed in the Driver Information Center, the Computer?Controlled Cranking System will be disabled.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · VEHICLE SPEED CONTROL:CRUISE CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a groan, growl, or moan coming from the vehicle when operating the vehicle in four wheel drive. Driving on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for an extended period of time may cause premature wear on your vehicle's power train. Dealer should advise the customer not drive on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for extended periods of time.
Source components: POWER TRAIN · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that unable to program the key fobs to the vehicle. Technician will need to contact Techline Customer Support Center to obtain calibrations if adding Remote Keyless entry.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the cruise control being inoperative. Technician may find Diagnostic Trouble Code B3894 set in the Trailer Brake Control Module. Technician should follow published Service Information diagnostics first. Technician should check the "Master Cylinder Pressure" sensor parameter listed in the Trailer Brake Control Module data list. If it is displaying pressure with no brake pedal input, suspect a concern with the Master Cylinder Pressure Sensor, wiring/terminals, or Electronic Brake Control Module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have passenger window express down feature is inoperative. Technician should be advised that models equipped with either Memory Seats Regular Production Option Code (AN3) and/or Power Folding Mirrors Regular Production Option Code (DL3) will have the passenger window express down feature. Dealer should advised the customer if the vehicle does not have one of the Regular Production Option Codes AN3 and or DL3, this is a normal operating characteristic.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC: WILL HAVE INOPERATIVE CRUISE CONTROL; INOPERATIVE OR UNWANTED ACTIVATION OF RADIO CONTROLS; BACKLIGHTING FLASHES, FLICKERS OR INOPERATIVE DUE TO POSSIBLE SHORT TO GROUND ON STEERING WHEEL COIL CONNECTOR X2. MODELS 2007-2013 ESCALADES MODELS, AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA, YUKON MODELS. *PE
Source components: ELECTRICAL SYSTEM · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET/CADILLAC: INSTRUMENT PANEL MESSAGES REGARDING STABILITRAK MESSAGE, TRACTION CONTROL MESSAGE, SERVICE BRAKE SYSTEM MESSAGE, IS OFF AND GAUGES, IN VARIOUS MODULES LOW SPEED SETTINGS, ARE INOPERATIVE. MODELS 2007-13 ALL ESCALADES; AVALANCHE, SILVERADO, SUBURBAN, TAHOE; SIERRA, ALL YUKONS AND DENALIS. *PE
Source components: ELECTRONIC STABILITY CONTROL (ESC) · ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · TRACTION CONTROL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/GMC/CHEVROLET: INFORMATION ON CRUISE CONTROL BEING INOPERATIVE DUE TO BPP CIRCUIT SIGNAL AND/OR TCC/CRUISE BRAKE PEDAL PARAMETERS, WHEN BRAKE PEDAL IS RELEASED BUT SHOWS APPLIED. MODELS 2007-2013 ALL ESCALADES, AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA, ALL YUKONS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC: THERE IS SLIPPING OR HAVE NO FOURTH, FIFTH OR SIXTH GEAR AND MALFUNCTION INDICATOR LAMP (MIL) WOULD BE ON, WITH DIAGNOSTIC TROUBLE CODE (DTC) P0796 FOUND AS ACTIVE. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/CADILLAC/GMC: CERTAIN VEHICLES EXPERIENCING ERRATIC OR INOPERATIVE SPEEDOMETER OR ANTI-LOCK BRAKE SYSTEM MESSAGE OR MALFUNCTIONING INDICATOR LIGHT DISPLAYING IN DRIVER'S INFORMATION CENTER. *PE UPDATED 08/5/2013 *JS
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: J-35616-64B TERMINAL TEST PROBE AND REPLACEMENT TERMINAL. ALSO INCLUDED MODELS VERANO, REGAL, LACROSSE, CTS, SRX, VOLT, SONIC, MALIBU, IMPALA, EQUINOX, CRUZE, AVALANCHE, TAHOE SUBURBAN, SILVERADO, SIERRA, YUKON, AND TERRAIN FOR MODEL YEAR 2013. MODEL ESCALADE MODEL YEAR 2012-2013. MODEL PONTIAC G3 MODEL YEAR 2007. MODEL WAVE MODEL YEARS 2005-2010. DENALI MODELS MODEL YEARS 2007-2013. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: DIAGNOSIS AND REPAIR- MALFUNCTION INDICATOR LAMP ILLUMINATED, REDUCE ENGINE POWER MESSAGE DISPLAYED, DTC P2135 SET. ALSO INCLUDED MODEL SIERRA DENALI YEAR 2010-2011 *JS
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: TICK OR RATTLE NOISE FROM FRONT OF DASH, TRANSMISSION FILLER TUBE CRACKED OR BROKEN (INSPECT FILLER TUBE, REPLACE TUBE AS NECESSARY). *JS UPDATED 05/3/2013 *JS
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: LOSS OF HIGH SPEED GMLAN COMMUNICATIONS, INTERMITTENT NO CRANK, IP GAGE FLUCTUATION, INTERMITTENT DOOR LOOK CYCLING, INTERMITTENT CHIME OPERATION, VARIOUS IP WARNING LAMPS ILLUMINATED, TRANSMISSION MAY NOT SHIFT, COMMUNICATION DTCS U0073, U0100, U0101, U0102 U0121 OR U0140 SET (REPAIR TERMINALS IN TRANSMISSION HARNESS CONNECTOR, REPAIR OPEN OR SHORTED GM HIGH SPEED LAN CIRCUITS, OPEN OR SHORTED DATA LINK RESISTOR, CORROSION OR POOR CONNECTIONS IN VARIOUS CONTROL MODULE CONNECTORS). *JS
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC: CORRECT FRONT AXLE VENT HOSE ROUTING. THE FRONT AXLE VENT HOSE IS MOUNTED IN THE LEFT SIDE OF THE ENGINE COMPARTMENT, AND MAY NOT BE CORRECTLY ROUTED. *PE UPDATED ON 5/1/2012. *KB
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ILLUMINATION OF CHECK ENGINE SOON LIGHT MAY BE CAUSED BY EVAPORATIVE EMISSION CANISTER PURGE SOLENOID VALVE NOT FUNCTIONING PROPERLY. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: SEE DOCUEMTN SEARCH BUTTON FOR OWNER LETTER. AUXILIARY BATTERY FEED MAY CAUSE FUSIBLE LINK TO MELT AND OPEN CIRCUIT TO PREVENT DAMAGE OR FIRE IN WIRING HARNESS, DUE TO ELECTRICAL OVER LOAD. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: DIAGNOSTIC INFORMATION FOR INTERMITTENT RESTRAINTS, AIR BAG (SIR) INDICATOR/LAMP ON WITH DTC(S) B0012, B0013, B0016, B0016, B0019, B0020, B0022, B0023, B0026, B0033, B0040, B0042 OR B0044 SET. THIS MAY BE CAUSED BY A LOOSE, MISSING, OR BROKEN CONNECTOR POSITION ASSURANCE (CPA) RETAINER AT THE AIR BAG FOR THE SET DTC. INCLUDES TRAILBLAZER EXT. *PE UPDATED 8/16/10. *PE UPDATED 3/12/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC/HUMMER: SOME SUVS AND TRUCKS ARE EXHIBITING A CONDITION WHERE BY GRINDING/RATCHETING TYPE NOISE COMING FROM AUTOMATIC TRANSMISSION WHEN SHIFTING INTO PARK WHILE IN 4WD LOW (4LO) RANGE. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET/HUMMER/GMC/PONTIAC/CADILLAC/SATURN: TECHNICIANS MAY FIND DTCS P0601, P0603, P0604, P062F OR P1621 STORED IN THE TCM AS AN ACTIVE OR A HISTORY CODE. SOME OF THESE DTCS CAN ALSO BE SET IN THE ECM OR FPCM. MAKE SURE THAT YOU KNOW WHICH MODULE (FOR EXAMPLE ECM, FPCM OR TCM) HAS SET THE DTC BEFORE ATTEMPTING TO DIAGNOSE AND REPAIR THIS CONDITION. *PE UPDATED 8/1/11. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).