2009 Chevrolet SILVERADO Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 277, ordered newest first. Dated records on this page: Oct 24, 2013–Jul 17, 2017.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 17, 2017Service Bulletin/Repair Instructions
06-03-09-004H
NHTSA communication ID: 10108599
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to lube the rear leaf springs on vehicles with the condition of a squeak noise originating from the rear of the vehicle.
Source components: SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
14648A - Customer Satisfaction. Certain vehicles have a performance issue with their OnStar modules that could impact the vehicle?s battery life. If the vehicle?s OnStar module contains this condition, the OnStar green telltale light will be illuminated even when the vehicle is off. This condition can drain the vehicle?s battery if the vehicle is not started for approximately four days. The condition may also render the OnStar system inoperative, which would disable all OnStar services, including automatic crash response and emergency roadside services. This condition can occur even if the vehicle is not actively subscribed to OnStar. Dealers are to remove the fuse for the OnStar module to reset it.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with a list of modules to check for communication with the scan tool, if the navigation radio does not display the current Hybrid mode. Dealer will use a scan tool to check communication with Accessory Direct current Power Control Module, Air Condition control module, Drive Motor Generator Power Inverter Module, Engine Control Module, Battery Energy Control Module, and Transfer Case Control Module. Repair the loss of communication with the affected module and the power flow should return to the radio display.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, LC8, LC9, LH9, LMF, LMG, LY6, or LZ1. Vehicle may have Service Engine Soon lamp with Diagnostic Trouble Code P0521 or Low Oil Pressure message on the instrument panel. Dealer will need to determine if bulletin 10-06-01-008 was completed. If the bulletin was performed inspect the left rocker cover. Dealer will insure the left rocker can hold water without leaking. If leaks are found apply room temperature vulcanization silicone to the rocker cover if possible or replace the left rocker cover.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with the additional steps that are needed to help perform a successful brake bleed on the 2-Mode Hybrid with Regular Production Option Code HP2. With a battery maintainer installed on the vehicle use brake pressure bleeder that maintains 30 psi for the entire bleed procedure.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A COLD ENGINE TICK NOISE FOR 50 SECONDS AT START UP. TECHNICIAN DETERMINES IF THE TICK NOISE IS POSSIBLY COMING FROM THE EXHAUST MANIFOLD, AS THIS NOISE COULD EASILY BE MISTAKEN FOR AN ENGINE TICK NOISE. IF YOUR SI DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN, THIS CONCERN SHOULD BE CONSIDERED A VEHICLE DESIGN CHARACTERISTIC OF THE ECM CALIBRATION AND NO ADDITIONAL REPAIRS SHOULD BE PERFORMED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to apply dielectric grease and a piece of adhesive shim stock to the steering angle sensor connector to correct a condition of service stabilitak message displayed in DIC and DTC C0455 or C0710
Source components: STEERING · STEERING:ELECTRIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and bleed the power steering system to correct a condition of power steering noise or fluid leak from power steering pump, gear or high pressure hose during extreme low temperature conditions.
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 - Suspected Tampering or Vehicle Modifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for the re-torque of leaf spring bolts to correct a customer concern for a clunking noise coming from the rear of the vehicle.
Source components: SUSPENSION · SUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY · SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for the re-torque of leaf spring bolts to correct a customer concern for a clunking noise coming from the rear of the vehicle.
Source components: SUSPENSION · SUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY · SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2015 model year to repair information on correcting a customer concern of poor, limited, reduced Remote Keyless Entry (RKE) or Remote Vehicle Start (RVS) range.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET/PONTIAC/SATURN/SAAB/GMC/CADILLAC: TSB CONTAINS AN OWNER NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. IN CERTAIN VEHICLES AND SUVS, ONSTAR MODULE GREEN TELLTALE LIGHT IS ILLUMINATED WHEN VEHICLE IS OFF AND DRAINING BATTERY AND VEHICLE NOT ABLE TO START AFTER FOUR (4) DAYS AND WOULD DISABLE ALL ONSTAR SERVICES. *PE
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: LOW BEAM HEADLAMP BULB DIAGNOSIS/ REPLACEMENT (INSPECT BULB AND CONNECTOR). DO NOT REPLACE THE ENTIRE HEADLAMP ASSEMBLY FOR THIS CONDITION. REPLACE THE BULB AND INSPECT THE CONNECTOR. *JS UPDATED 4/7/15. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THERE IS UNWANTED STABILITY ACTION OR STABILITY LIGHT ON. THIS CAN BE CAUSED BY THE SUSPENSION BEING MODIFIED. *RM UPDATED 6/18/12. *PE MODELS 2007-13 ALL ESCALADE; AVALANCHE, SILVERADO, SUBURBAN, TAHOE; SIERRA, SIERRA DENALI, ALL YUKONS. UPDATED 11/28/12. *PE UPDATED 4/1015. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC CHEVROLET SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. MATERIAL OVER SENSING & DIAGNOSTIC MODULE RETAINING MOISTURE. VEHICLES MAY HAVE A CONDITION WHERE AN ELECTRONIC COMPONENT LOCATED BENEATH THE DRIVER'S SEAT MAY CORRODE DUE TO A SIGNIFICANT QUANTITY OF SNOW AND/OR WATER CONTAINING ROAD SALT OR OTHER CONTAMINANTS ENTERING THE VEHICLE AND SATURATING THE ACOUSTICAL PADDING BENEATH THE CARPET. CSC LETTER WAS RECEIVED. *PE UPDATED 4/7/15. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and now is refered to Article 3.2.9 of the 1st addition manual for details of Technician Identification and Accounting of Labor Time
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the OnStar LED is staying on after the vehicle Retained Accessory Power has turned off and/or their Bluetooth phone stays connected after leaving the vehicle. Technician will need to check the Station Identification number. If the Station Identification number falls in the range technician will need to perform an over the air system programming.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the OnStar LED is staying on after the vehicle Retained Accessory Power has turned off and/or their Bluetooth phone stays connected after leaving the vehicle. Technician will need to perform a power cycle to the Vehicle Communication Interface Module. If the concern is gone, no further action is required. If the concern is still present after the power cycle technician will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: ENGINES, WITH EGR SYSTEM, HAS LEAKAGE FROM EGR COOLER ENGINE COOLANT INTO THE COMBUSTION CHAMBER. MODEL 2002-15 SILVERADO, SIERRA, 2004-09 KODIAK C4500-C5500, TOPKICK C4500-C5500, 2006-15 EXPRESS, SAVANA. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle's 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector from General Motors Customer Care and Aftersales along with the trailer's 7-way connector plug.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL · TRAILER HITCHES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the operation of the ground illumination lamp. For the puddle lamps to operate they must be turned on using the Drivers Information Center buttons and it must be dark outside.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have "Press check to turn off motion sensor" message on the Driver Information Center. If this message is displayed, the vehicle has a General Motors Accessory shock sensor, motion sensor or inclination sensor installed. Dealer should advise the customer this is normal operation with this accessory installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on or reduced engine power message. Technician may find Diagnostic Trouble Codes P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138. Technician will need to inspect the Accelerator Pedal Position circuits for poor terminal tension.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: AN OPTIONAL ENGINE BLOCK HEATER PLUG IN FOR ONBOARD AC POWER AND WITH CONTINUOUS USAGE WILL RESULT IN SHORTING OF WIRES, OVER HEATING SYSTEM, ELECTRICAL FAILURE AND COMPARTMENT ENGINE FIRES. MODEL 2003-15 EXPRESS CUT AWAY VANS, SILVERADO CHASSIS CAB, SAVANA CUT AWAY VANS, SIERRA CHASSIS CAB. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC: LOSS OF PROPULSION, WHEN SPEED IS LESS THAN 5 KM/H (3MPH), SERVICE HYBRID SYSTEM IS DISPLAYED IN DRIVER INFORMATION CENTER (DIC) AND MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATES. MODEL 2008-2013 ESCALADE, SILVERADO, TAHOE, SIERRA, YUKON. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B15517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an air condition that has poor performance during high ambient temperatures. Technician will need to check the refrigerant charge and record the recovered amount on the repair order. Technician should recharge the system if needed. Technician will also need to verify if Global Diagnostic System 2 high side readings match a high side pressure gauge. If the readings vary greatly diagnostics will need to be performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Auxiliary Transmission Fluid Pump Control Module and Auxiliary Transmission Fluid Pump placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 2-Mode Drive Motor Generator Battery placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 2ML70 Transmission Assembly will be placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: SOME VEHICLES/TRUCKS MAY EXPERIENCE A NO CRANKING OR STARTING, CAUSED BY POSSIBLE EXCESSIVE LEAKAGE FROM CYLINDER PAST EXHAUST OR INTAKE VALVE, LOW STATIC COMPRESSION, SENSOR IS DISCONNECTED, OR WHILE CRANKING, VALVE TRAIN FAILS TO MOVE. MODEL 2009-2014 CORVETTE, CAMARO, EXPRESS, SS, SILVERADO, SUBURBAN, TAHOE, SAVANA, SIERRA, YUKON. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a an extended crank on cold start, brief rough running on cold start, black exhaust color, and/or Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0172 and or P0175. Technician will need to check the Fuel Alcohol Content parameter found in the Fuel Trim Data List of the scan tool and the measured ethanol content of a fuel sample using the J44175 tester. If the difference is 17% or greater, reprogram the Engine Control Module with the latest calibrations from TIS2web.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a groan, growl, or moan coming from the vehicle when operating the vehicle in four wheel drive. Driving on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for an extended period of time may cause premature wear on your vehicle?s power train. Dealer should advise the customer not drive on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for extended periods of time.
Source components: POWER TRAIN · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: STRUCTURE:BODY:TAILGATE · STRUCTURE:BODY:TAILGATE:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have navigation or radio screen is blank or flashes on and off, no sound from speakers, and rear DVD screen inoperative. Technician will find Diagnostic Trouble Codes B1265, B1288, or B1289. Technician will need to repair circuit 7066.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a groan, growl, or moan coming from the vehicle when operating the vehicle in four wheel drive. Driving on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for an extended period of time may cause premature wear on your vehicle's power train. Dealer should advise the customer not drive on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for extended periods of time.
Source components: POWER TRAIN · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code B2555 may be found in a Driver and/or Passenger Door Module. Technician should ignore the Diagnostic Trouble Code if set in a DDM and/or PDM on a vehicles not equipped with front door panel courtesy lights.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that after refueling the fuel gauge will show empty. Technician may find Diagnostic Trouble Code P2636 has set. Technician should be advised that the vehicle is being refueled with the engine running or ignition on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published "Engine Cranks But Does Not Run" diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that after installing the GM Accessory Heated Seat Kit, one or more of the following issues may be present the heated seat back and/or bottom turns off after approximately 30 seconds and after turning on the heated seat switch, the indicators remain on, but the seat is not heating. Technician may find Diagnostic Trouble Codes B1935 Sym 0E, B2180 Sym 0E, B2425 Sym 0D, and/or B2430 Sym 0D. Technician will need to inspect the accessory heated seat wiring harness and make sure the heater element connectors are installed correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have tailgate may not lower slowly like the New 2014 Silverado 1500 / Sierra 1500 models. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: EQUIPMENT:ELECTRICAL · STRUCTURE:BODY:TAILGATE · STRUCTURE:BODY:TAILGATE:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Technician will need to ensure fleet vehicles with RPO 6E2 or 6E8 should be checked to verify that the Theft Deterrent Module is in fleet mode prior to attempting to add keys.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a random bump, chuggle, or fishbite sensation when crowding the throttle slightly with the Torque Converter Clutch on while cruising at 35-60 miles per hour. Technician should follow all published Service Information diagnostics if the concern is repaired compare to a like vehicle with the same options.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that unable to program the key fobs to the vehicle. Technician will need to contact Techline Customer Support Center to obtain calibrations if adding Remote Keyless entry.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that are unable to override the automatic door locking feature. Technician will update the Body Control Module on 2006 to 2007 model years. On 2010 to 2014 model years technician will need to contact Techline Customer Support for calibrations.
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES:DOORS:LATCH · STRUCTURE:BODY:DOOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customer's wanting to add the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full Size pickup/utility when the vehicle was not ordered with the option. Dealer should advise the customer that if the vehicle does not have the option Regular Production Option Code (JL1) it cannot be added to the vehicle.