The manufacturer’s record · Page 13 of 17
Original record summaries, dates and identifiers for this model-year. Records 1,201–1,300 of 1,652, ordered newest first. Dated records on this page: Jan 14, 2014–Jun 1, 2014.
Back to 2010 Chevrolet SILVERADO 1500 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10247674
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Charging System Message Or Low Volt Gauge Reading After Cold Start.
Source components: ELECTRICAL SYSTEM.
Source record 10247674 at NHTSANHTSA communication ID: 10247673
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Charging System Message Or Low Volt Gauge Reading After Cold Start
Source components: ELECTRICAL SYSTEM.
Source record 10247673 at NHTSANHTSA communication ID: 10247112
NHTSA source summary · Original PDF not reviewed by Recallfolio
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10247112 at NHTSANHTSA communication ID: 10247083
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistle Noise From Drivers Side A Pillar Area.
Source components: STRUCTURE.
Source record 10247083 at NHTSANHTSA communication ID: 10245313
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Charging System Message Or Low Volt Gauge Reading After Cold Start.
Source components: ELECTRICAL SYSTEM.
Source record 10245313 at NHTSANHTSA communication ID: 10245312
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Charging System Message Or Low Volt Gauge Reading After Cold Start
Source components: ELECTRICAL SYSTEM.
Source record 10245312 at NHTSANHTSA communication ID: 10137937
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.
Source components: TIRES.
Source record 10137937 at NHTSANHTSA communication ID: 10137935
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
Source components: ENGINE · POWER TRAIN.
Source record 10137935 at NHTSANHTSA communication ID: 10137934
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10137934 at NHTSANHTSA communication ID: 10137932
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10137932 at NHTSANHTSA communication ID: 10137928
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
Source components: EQUIPMENT · TIRES.
Source record 10137928 at NHTSANHTSA communication ID: 10137927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer.
Source components: EQUIPMENT · TIRES.
Source record 10137927 at NHTSANHTSA communication ID: 10137919
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
Source components: EQUIPMENT.
Source record 10137919 at NHTSANHTSA communication ID: 10137915
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains a normal condition from changes in Exhaust Tone for Active Fuel Management Engines when in Three or Four Cylinder Mode
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.
Source record 10137915 at NHTSANHTSA communication ID: 10137914
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
Source components: EQUIPMENT.
Source record 10137914 at NHTSANHTSA communication ID: 10137901
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10137901 at NHTSANHTSA communication ID: 10137890
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT · POWER TRAIN.
Source record 10137890 at NHTSANHTSA communication ID: 10253176
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Exhaust Fluid System Message Displayed.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10253176 at NHTSANHTSA communication ID: 10253148
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auxiliary Transmission Fluid Pump.
Source components: POWER TRAIN.
Source record 10253148 at NHTSANHTSA communication ID: 10247678
NHTSA source summary · Original PDF not reviewed by Recallfolio
High Voltage 2-Mode Battery Parts Restriction-TAC
Source components: ELECTRICAL SYSTEM.
Source record 10247678 at NHTSANHTSA communication ID: 10245317
NHTSA source summary · Original PDF not reviewed by Recallfolio
High Voltage 2-Mode Battery Parts Restriction-TAC
Source components: ELECTRICAL SYSTEM.
Source record 10245317 at NHTSANHTSA communication ID: 10069968
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10069968 at NHTSANHTSA communication ID: 10135235
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer
Source components: ELECTRICAL SYSTEM.
Source record 10135235 at NHTSANHTSA communication ID: 10111821
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a ?Service Exhaust Fluid System? and a ?See Owner?s Manual Now? message displayed on the Instrument Panel Cluster. Technician may find reductant level sensor Diagnostic Trouble Codes P203D, P21AB, and P21B0 set. Technician will need to follow published Service Information diagnostics for the Diagnostic Trouble Codes that are set. If no wiring concerns are found replace the Diesel Exhaust Fluid tank assembly.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT.
Source record 10111821 at NHTSANHTSA communication ID: 10135219
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
Source components: EXTERIOR LIGHTING.
Source record 10135219 at NHTSANHTSA communication ID: 10135218
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
Source components: EQUIPMENT.
Source record 10135218 at NHTSANHTSA communication ID: 10111818
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 2010 through 2015 6.6L Duramax Diesel Engine Fuel Injection Pump Part numbers 12645102, 12658095 and 12661059 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
Source components: ENGINE.
Source record 10111818 at NHTSANHTSA communication ID: 10111811
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10111811 at NHTSANHTSA communication ID: 10111810
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111810 at NHTSANHTSA communication ID: 10111805
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE).
Source record 10111805 at NHTSANHTSA communication ID: 10135202
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on how to disable high voltage safely.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10135202 at NHTSANHTSA communication ID: 10135201
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10135201 at NHTSANHTSA communication ID: 10135200
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to install a new cabin air filter kit for vehicles that did not have one if the customer whants one installed to fix the concern of dust intruding into cabin interior.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10135200 at NHTSANHTSA communication ID: 10135197
NHTSA source summary · Original PDF not reviewed by Recallfolio
The purpose of this document is to provide the Service Personnel with a guide to determine which Service Information documents and scan tool parameters to reference when encountering an: Exhaust Fluid Quality Poor Message Displayed, and a Reductant Fluid Quality Test Status that will Pass, Time Out, Fail or Interrupt and other DEF Messages that may be observed.
Source components: ENGINE AND ENGINE COOLING.
Source record 10135197 at NHTSANHTSA communication ID: 10111783
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
Source components: FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS.
Source record 10111783 at NHTSANHTSA communication ID: 10253175
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Exhaust Fluid System Message Displayed.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10253175 at NHTSANHTSA communication ID: 10250013
NHTSA source summary · Original PDF not reviewed by Recallfolio
High Voltage Safety ? High Voltage Disabling
Source components: ELECTRICAL SYSTEM.
Source record 10250013 at NHTSANHTSA communication ID: 10247727
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bump Feel Or Clunk Noise After A Stop.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10247727 at NHTSANHTSA communication ID: 10247072
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bump Feel Or Clunk Noise After A Stop.
Source components: SERVICE BRAKES.
Source record 10247072 at NHTSANHTSA communication ID: 10069957
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10069957 at NHTSANHTSA communication ID: 10137887
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10137887 at NHTSANHTSA communication ID: 10111884
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
Source components: EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK ASSEMBLY · FUEL SYSTEM, GASOLINE.
Source record 10111884 at NHTSANHTSA communication ID: 10111876
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube box/hitch, etc. to the rear of the truck, which affects the rear park assist operation. Technician can disable the rear park assist for this concern.
Source components: STRUCTURE:BODY:BUMPERS.
Source record 10111876 at NHTSANHTSA communication ID: 10111875
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
Source components: ENGINE.
Source record 10111875 at NHTSANHTSA communication ID: 10137868
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the customer to clean the exhaust filter when prompt to or the MIL may come on and the truck DPF system may fail.
Source components: ENGINE AND ENGINE COOLING.
Source record 10137868 at NHTSANHTSA communication ID: 10137866
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
Source components: EQUIPMENT.
Source record 10137866 at NHTSANHTSA communication ID: 10111850
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111850 at NHTSANHTSA communication ID: 10111849
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10111849 at NHTSANHTSA communication ID: 10111848
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111848 at NHTSANHTSA communication ID: 10111846
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a customer?s request to install OnStar Bluetooth. Dealer should be advised at this time, there are no provisions to add this option to vehicles that were not built with it.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111846 at NHTSANHTSA communication ID: 10111845
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10111845 at NHTSANHTSA communication ID: 10247703
NHTSA source summary · Original PDF not reviewed by Recallfolio
Removing / Disabling Rear Park Assist RPO UD7.
Source components: BACK OVER PREVENTION:SOFTWARE · UNKNOWN OR OTHER.
Source record 10247703 at NHTSANHTSA communication ID: 10247681
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information On Requests To Add OnStar Bluetooth Option.
Source components: EQUIPMENT.
Source record 10247681 at NHTSANHTSA communication ID: 10245950
NHTSA source summary · Original PDF not reviewed by Recallfolio
Canadian Customers Unable To Place Calls In The United States
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10245950 at NHTSANHTSA communication ID: 10245342
NHTSA source summary · Original PDF not reviewed by Recallfolio
Removing / Disabling Rear Park Assist RPO UD7.
Source components: ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:SENSORS · ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:SOFTWARE.
Source record 10245342 at NHTSANHTSA communication ID: 10073396
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10073396 at NHTSANHTSA communication ID: 10070906
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: STEERING.
Source record 10070906 at NHTSANHTSA communication ID: 10065826
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10065826 at NHTSANHTSA communication ID: 10138655
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to install double sided tape to the windshield molding to correct the customers concern of a tapping or clicking noise at the winshield area.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · VISIBILITY:WINDSHIELD.
Source record 10138655 at NHTSANHTSA communication ID: 10138651
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains the use of diesel fuel additives to remove water or enhance performance.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, DIESEL.
Source record 10138651 at NHTSANHTSA communication ID: 10111966
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111966 at NHTSANHTSA communication ID: 10111964
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111964 at NHTSANHTSA communication ID: 10138646
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
Source record 10138646 at NHTSANHTSA communication ID: 10111959
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a clunk type noise on start up with the vehicle in park when the vehicle is equipped Allison LCT1000 transmission. This condition is considered to be an operating characteristic of the Allison LCT1000 transmission.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10111959 at NHTSANHTSA communication ID: 10111956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: ENGINE.
Source record 10111956 at NHTSANHTSA communication ID: 10138640
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
Source record 10138640 at NHTSANHTSA communication ID: 10138639
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician the proper way to install and torque the wheel.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · WHEELS.
Source record 10138639 at NHTSANHTSA communication ID: 10138638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
Source components: WHEELS.
Source record 10138638 at NHTSANHTSA communication ID: 10138637
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES · WHEELS:RIM.
Source record 10138637 at NHTSANHTSA communication ID: 10138631
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
Source components: TIRES · WHEELS:RIM.
Source record 10138631 at NHTSANHTSA communication ID: 10138630
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains the use of Nitrogen in GM tires.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES.
Source record 10138630 at NHTSANHTSA communication ID: 10138629
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and recommended practices.
Source components: TIRES.
Source record 10138629 at NHTSANHTSA communication ID: 10138621
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138621 at NHTSANHTSA communication ID: 10111934
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Drive Motor Generator Control Module, also known as PIM) for the 2-Mode Hybrid Utilities and Trucks are being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111934 at NHTSANHTSA communication ID: 10111927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, GASOLINE · SERVICE BRAKES, HYDRAULIC.
Source record 10111927 at NHTSANHTSA communication ID: 10138609
NHTSA source summary · Original PDF not reviewed by Recallfolio
The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138609 at NHTSANHTSA communication ID: 10138606
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a windshield.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · VISIBILITY:WINDSHIELD.
Source record 10138606 at NHTSANHTSA communication ID: 10138605
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10138605 at NHTSANHTSA communication ID: 10111911
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that First Responder Guides for General Motors vehicles can be accessed via the web at http://www.gmstc.com.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111911 at NHTSANHTSA communication ID: 10138601
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to inspect the transmissions filter for splits or cracks to correct the customers concern for no forward, reverse or slips.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10138601 at NHTSANHTSA communication ID: 10111894
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111894 at NHTSANHTSA communication ID: 10111892
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a cold engine tick noise for 50 seconds at start up. Technician determines if the tick noise is possibly coming from the exhaust manifold, as this noise could easily be mistaken for an engine tick noise. If your SI diagnosis does not isolate the cause of this concern, this concern should be considered a vehicle design characteristic of the ECM calibration and no additional repairs should be performed.
Source components: ENGINE.
Source record 10111892 at NHTSANHTSA communication ID: 10253174
NHTSA source summary · Original PDF not reviewed by Recallfolio
NQG 4WD Models With Noise Vibration On Dry Pavement.
Source components: POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
Source record 10253174 at NHTSANHTSA communication ID: 10253135
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cold Extended Crank .
Source components: ENGINE AND ENGINE COOLING.
Source record 10253135 at NHTSANHTSA communication ID: 10246621
NHTSA source summary · Original PDF not reviewed by Recallfolio
Car and Truck Fix it Right the First Time Issues
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10246621 at NHTSANHTSA communication ID: 10190932
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190932 at NHTSANHTSA communication ID: 10190931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190931 at NHTSANHTSA communication ID: 10137784
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
Source components: EQUIPMENT.
Source record 10137784 at NHTSANHTSA communication ID: 10112045
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10112045 at NHTSANHTSA communication ID: 10137781
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137781 at NHTSANHTSA communication ID: 10112013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10112013 at NHTSANHTSA communication ID: 10112006
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns.
Source components: PARKING BRAKE:DRIVELINE.
Source record 10112006 at NHTSANHTSA communication ID: 10112005
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
Source record 10112005 at NHTSANHTSA communication ID: 10112000
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
Source record 10112000 at NHTSANHTSA communication ID: 10111998
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 6.6L Diesel Engine Fuel Injection Pump part numbers 12645102 and 12658095 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
Source components: ENGINE · FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP.
Source record 10111998 at NHTSANHTSA communication ID: 10111997
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
Source components: EQUIPMENT.
Source record 10111997 at NHTSANHTSA communication ID: 10111993
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B15517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10111993 at NHTSANHTSA communication ID: 10137777
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10137777 at NHTSANHTSA communication ID: 10137776
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER · POWER TRAIN:CLUTCH ASSEMBLY.
Source record 10137776 at NHTSANHTSA communication ID: 10111986
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER.
Source record 10111986 at NHTSA