2012 Chevrolet CRUZE Manufacturer communications & TSBs.Page 13
Original record summaries, dates and identifiers for this model-year. Records 1,201–1,300 of 1,816, ordered newest first. Dated records on this page: Feb 19, 2014–Jun 26, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 26, 2014Service Bulletin/Repair Instructions
PI1237A
NHTSA communication ID: 10126307
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary was created to inform the technician of a possible camshaft position exticer wheel not properly installed, if the engine was just previously repaired,and procedure on how to use the special tool to install the exciter wheels properly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Technician will need to use a scan tool and verify current Digital Radio Receiver Status under Data Display. Technician will need to look at the second line labeled Digital Radio Receiver Status will display a number of 00 - 04. Technician will repair per the status code.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to install a seat cushion lateral retair to correct the customers concern of the drivers and passenger seat moving laterally, clunking, squeaking, clicking, or shifting around while cornering.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that loose connection between the vehicle and a Bluetooth phone. Technician will need to use a scan tool to check the "Firmware Over-the-Air" value. If the "Firmware Over-the-Air" value is up to date and customer's concern is still present contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains if the fuse is open when the customer plugs in the trailer, that it may be the cause if diagnostics finds no problems to that point.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have the Antilock Braking System, Service Traction Control System, and/or Service Stabilitrak lights are on. The Electronic Brake Control Module may have one or more of the following Diagnostic Trouble Codes C0035-C0050 with specifically symptom 18, 5A, or 0F. Technician will gain access to the correct wheel bear per the Diagnostic Trouble Code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
Source components: SERVICE BRAKES, AIR:ANTILOCK · SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary was created to inform the technician of a possible camshaft position exticer wheel not properly installed, if the engine was just previously repaired,and procedure on how to use the special tool to install the exciter wheels properly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin states to add the DTC symptom byte to the documentation to help aid engineering pinpoint concerns when trying to locate a root cause.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: DUE TO LOOSE GROUND TERMINAL CONNECTIONS, IN SOME VEHICLES AND TRUCKS EXPERIENCE, ACCESSORIES MALFUNCTIONS, DIC MESSAGES, IPC WARNING INDICATORS, SES LIGHT ON. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THE BRAKE, TRACTION, OR STABILITY LIGHTS ARE ON BECAUSE OF DEBRIS STUCK ON THE WHEEL SPEED SENSOR. UPDATED ON 06/15/2011. *KB UPDATED ON 06/20/2011. *RM UPDATED 6/27/11. *PE UPDATED 10/3/11. *PE UPDATED 05/08/2013 *JS UPDATED ON 7/9/2013. *KB UPDATED 7/28/14. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure to replace the starter and fuse block to correct the customer concern of a knocking noise on start up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to lube the clutch pedal pin and clutch pedal return spring to correct the customers concern of a squeaking clutch pedal.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to repair or replace the steering column seal to correct the customers concern of a groan, squeak or rubbing noise when turning the steering wheel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a customer?s request to install OnStar Bluetooth. Dealer should be advised at this time, there are no provisions to add this option to vehicles that were not built with it.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a list of message codes that are not included in the owners manual if the customer states that it was displayed on the DIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to install a new coolant drain tube and clean any greese found under the windshield cowl to correct a customers concern of a coolant odor inside the vehicle.
Source components: ENGINE AND ENGINE COOLING · VISIBILITY:WINDSHIELD.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a grind growl noise on the 1-2 shift that can be felt in the clutch pedal and brake pedal if applied during a 1-2 shift under light or normal acceleration. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: SERVICE BRAKES · VEHICLE SPEED CONTROL:ACCELERATOR PEDAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that when replacing the camshaft part number 12626660. Technician will need to ensure that the date code and the finish of the camshaft. If the cam is discolored or has chatter marks, have parts department send the cam back as (MR code7) new defective.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to replace the starer and the fuse block to correct a customers concern of the starter or flywheel making a knocking noise.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:STARTER ASSEMBLY.