Original record summaries, dates and identifiers for this model-year. Records 1,301–1,400 of 1,527, ordered newest first. Dated records on this page: Dec 11, 2012–May 1, 2013.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 1, 2013Service Bulletin/Repair Instructions
130089004B
NHTSA communication ID: 10246617
NHTSA source summary · Original PDF not reviewed by Recallfolio
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of a customer concern where the heated seat indicator light is not functioning or the heated seats are not up to operating temperature during a remote vehicle start event. This is normal operation of the heated seat during a remote vehicle start event. The electronic climate control module is not in a complete wake up state during a remote vehicle start mode and will not enable the light emitting diode. After a cold soak below 32 degrees Fahrenheit the seat will not get hot in the 10 minutes or less of the remote vehicle start mode. This is due to the fact that the heat element is not in direct contract with the seat surface while the seat is unoccupied and the foam below the heater is full cold insulating air which takes time to heat up. Technician is to communicate to the customer this condition is a normal operating characteristic of their vehicle. It will not impact the designed performance or reliability of the vehicle. Please share this information with the customer, including a copy of this message.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when attempting to start vehicle "No Fob Detected" message is displayed. Technician will find the Key FOB works and the vehicle will start with the key FOB is placed in the pocket. Technician will need to replace the Key FOB with the Key FOB with Passive Entry Passive Start.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have excessive oil consumption and/or that they have to add oil between oil changes. Technician should reprogram the Engine Control Module with the latest TIS2web calibrations to adjust the engine oil life monitor to a maximum of 7,500 miles. Technician should also inspect for any obvious oil leaks that may explain the oil consumption complaint, and repair as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank. Dealer will ensure the customer is fully extending the key.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of diagnostic instructions to take when the key will not fold into the fob or will not stay in the folded position. The technician may comment that the key in the fob will not fold close or stay latched closed. Damage to the folding mechanism could result from storing the key in the door lock cylinder and accidently bumping or making contact with the key fob. Please advise all dealer personnel to refrain from storing the key in the door lock even for brief periods.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: ON SOME TRUCKS AND PASSENGER VEHICLES, ACCESSORY POWER OUTLETS (APO) AND TRAILER LIGHTING ARE COMMON ACCESSED ELECTRICAL SYSTEMS THAT ARE AFFECTED BY DEVICES THAT ARE PLUGGED IN AND BECOME INOPERATIVE DUE TO AN OPEN FUSE AND NO PROBLEM WITH VEHICLE IDENTIFIED. MODELS YEARS 2010-2014 TRUCKS AND PASSENGER. NO MODELS. *PE
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information accessory power outlet and trailer lighting fuse replacement due to electrical systems that can be affected by devices that are plugged in by the customer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have the Antilock Braking System, Service Traction Control System, and/or Service Stabilitrak lights are on. The Electronic Brake Control Module may have one or more of the following Diagnostic Trouble Codes C0035-C0050 with specifically symptom 18, 5A, or 0F. Technician will gain access to the correct wheel bear per the Diagnostic Trouble Code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an engine oil leak that appeared as they were driving the vehicle in extremely cold ambient temperatures. The technician may find the oil leak is coming from the rear main seal. Technician will need to check for proper thermostat operation by following thermostat Diagnosis as outlined in Service Information and replace the thermostat as necessary. Also the technician will remove the cam cover, inspect the positive crankcase ventilation baffle inside, and replace the cam cover if obvious sludge build up is present. Any debris in the positive crankcase ventilation pipes, hoses, the positive crankcase ventilation nipple on the cam cover, and the throttle body should be cleaned out. Technician should inspect the related positive crankcase ventilation hoses/connections for potential damage and replace if necessary. Run the engine at operating temperature for 15 minutes at idle. Then turn the engine off, and drain the engine oil for at least 15 minutes to remove all oil and condensation or water from the crankcase. Follow Service Information repair procedures to repair any oil leaks that were induced as a result of the frozen positive crankcase ventilation system and excessive crankcase pressure. Technician should insure the Engine Control Module calibrations have been installed to adjust the engine oil life monitor to a maximum of 7,500 miles (12,070 KM) as well.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
12312 - Customer Satisfaction Program. GM recently introduced into production a software update for the oil life monitor system that will enhance the way the engine oil is monitored and is providing it to customers who do not have this updated software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET/GMC: ENGINE IS MAKES RATTLING NOISE WHEN STARTING UP AND IS INTERMITTENT, AND IS HEARD IN CAMSHAFT POSITION ACTUATOR DUE TO ENGINE SHUT DOWN AND OIL PRESSURE NOT ALLOW TO CAMSHAFT POSITION ACTUATOR. MODELS 2011-2012 LACROSSE, REGAL, EQUINOX, ORLANDO, TERRAIN. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/SAAB: SOME VEHICLES HAVE FLOOR MATS THAT ARE DIFFICULT TO FULLY SEAT ON CARPET SIDE RETAINER DUE TO FLOOR RETAINER BEING BROKEN AND VARIOUS BREAKPOINTS FOR STYLE OF RETAINER AND BECAUSE DIFFERENT STYLES OR DESIGNS NOT INTERCHANGEABLE AND CONTAINS NON MATCHING RETAINERS. MODELS 2010-13 LACROSSE, SRX, 2011-13 REGAL, CRUZE, EQUINOX, VOLT, TERRAIN, 9-4X, 2012-13 VERANO, SONIC, 2008-13 CTS AND 2013 MALIBU. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information on replacement for the auxiliary floor mat retainer due to the floor mat retainer won't seat on the carpet.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have excessive oil consumption and/or that they have to add oil between oil changes. Technician should reprogram the Engine Control Module with the latest TIS2web calibrations to adjust the engine oil life monitor to a maximum of 7,500 miles. Technician should also inspect for any obvious oil leaks that may explain the oil consumption complaint, and repair as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have excessive oil consumption and/or that they have to add oil between oil changes. Technician should reprogram the Engine Control Module with the latest TIS2web calibrations to adjust the engine oil life monitor to a maximum of 7,500 miles.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a loud tick or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information on the driver airbag light is flashing in the cluster and/or the passenger airbag ON indicator does not illuminate when the passenger is present when the SDM setup has not been completed after reprogramming.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET: THERE IS AN OIL/FLUID LEAKAGE UNDER FRONT OF VEHICLE, POSSIBLY FROM WHEEL DRIVE SHAFT SEALS, AND ENGINEERING IS TRYING TO DETERMINE ROOT CAUSE OF LEAKAGE. MODELS 2011-2013 REGAL, CRUZE, 2012-2013 VERANO, SONIC. *PE
Source components: POWER TRAIN:DRIVELINE:DRIVESHAFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE ECM FOR CONCERNS REGARDING A LOUD RATTLE NOISE ON START UP THAT STOPS IN 3 SECONDS OR LESS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that loose connection between the vehicle and a Bluetooth phone. Technician will need to use a scan tool to check the "Firmware Over-the-Air" value. If the "Firmware Over-the-Air" value is up to date and customer's concern is still present contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information on doing a pressure line test prior to replacement and removal of the transmission for conditions relating to No Forward, No Reverse, No Crank, Engine Cranks But Will Not Start.