2010 Audi Q5 Manufacturer communications & TSBs.Page 10
Original record summaries, dates and identifiers for this model-year. Records 901–996 of 996, ordered newest first. Dated records on this page: May 13, 2009–Mar 25, 2013.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 25, 2013Service Bulletin/Repair Instructions
A191335 2025303-
NHTSA communication ID: 10123882
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES:DOORS:LATCH.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 11-48 dated July 25, 2011. Vehicle doors cannot be locked or unlocked using Advanced key. Vehicle cannot be started using the Start-Stop button. In Access/Start Authorization Control Module J518 (address word 05), DTC 03283 (Driver's side Access/Start Authorization Antenna Short Circuit to Ground), DTC 03284 (Right Access/Start Authorization Antenna Short Circuit to Ground) or DTC 00183 (Interior Access/Start Authorization Antenna 1 -R138-) are stored. Vehicle keys function properly otherwise, operating the door locks via the remote control as well as starting the vehicle using the ignition switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.
NHTSA source summary · Original PDF not reviewed by Recallfolio
One Daytime Running Light (DRL) intermittently flickers. One Daytime Running Light (DRL) intermittently lights up with more intensity then dims back to normal. The headlight beams still function normally. The LED DRL control unit's PWM output reacts to an intermittent system voltage change, causing the LED to flicker or change intensity. DTCs will not be logged in the vehicle electrical system control module, J519 (09). The customer complaint can only be sporadically reproduced.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer hears wind noise coming from the top of the vehicle while driving with the roof carrier bars installed. When the roof carrier bars are installed on the vehicle the acoustic environment in the cabin is predictably affected. The intent of the roof carrier bars is solely for the transport of cargo. When installed an increase in wind noise should be expected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 72 number 12-03 dated September 5, 2012. Customer may report squeak or rattle sounds coming from the rear seat area. The rattle sound can be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. The squeak noise may be coming from the rear seat armrest area, specifically from the contact surface between the armrest lock and the striker pin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 12-65 dated May 14, 2012. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the handle is slack.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 87 number 12-31 dated September 5, 2012. Moisture in the driver or front passenger foot well. Due to a faulty and / or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: THERE IS A GAP BETWEEN BODY AND SEALING SURFACE OF DRAIN HOSE THAT ALLOWS CONDENSATION FROM EVAPORATOR TO ENTER FRONT FOOT WELL AREA DUE FAULTY AND INCORRECT INSTALLATION OF CONDENSATION DRAIN HOSE. MODELS 2008-2013 A4, A5, A5 CABRIOLET, Q5. *PE
Source components: STRUCTURE:BODY · STRUCTURE:FRAME AND MEMBERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 40 number 12-26 dated September 26, 2012. Clicking or clacking noise when maneuvering or parking. Normal driving dynamics may cause microscopic movements between the wheel bearing and wheel bearing housing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 64 number 12-19 dated March 5, 2012. The customer may report noises when operating the window or noises from inside the door when driving on rough roads. When lowering the window, it collides with the clip that holds the window guide cable. This causes the clip to open and contact the window during operation, or rattle while driving on rough roads.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 26 number 12-10 dated March 30, 2012. MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage greater than 20,000 miles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 94 number 12-69 dated March 15, 2012. Part or all of the daytime running lights do not work on vehicles with LED DRLs. For vehicles with halogen DRLs, please reference TSB 2017488, 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EXTERIOR LIGHTING:HEADLIGHTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC? s are present in the engine control module:
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL on. Engine misfire. Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module.
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 94 number 12-78 dated June 4, 2012. A ? bulb out? warning is active in the instrument cluster?s Driver Information System (DIS) display and one or both of the rear side marker lights are burnt out. Moisture and debris can enter into the lower taillight housing causing one or more of the bulbs to burn out.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: IN THE DRIVER INFORMATION SYSTEM (DIS) INSTRUMENT CLUSTER, A WARNING IS ACTIVATED REGARDING BULB OUT AND ONE OR BOTH REAR SIDE MARKER LIGHTS ARE BURNT OUT, DUE TO POSSIBLE DEBRIS OR MOISTURE IN TAILLIGHT HOUSING. MODEL 2010-2013 Q5. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 94 number 11-52 dated October 11, 2011. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens. Damp air settles on the inside of a cold lens, which creates condensation. The headlight circulation system allows air from the outside to flow through the headlights. This open waterprotected ventilation system (needed for pressure compensation) creates different climate zones in the headlight: very warm areas, where the lens is warmed up by the light, and relatively cool areas, where the lens is cooled own by the air flow. Considerable differences in humidity and temperature between the inside and the outside of the headlights, even while driving, can lead to condensation. This is especially true in cold and wet weather, but it can also happen after a car wash, after steam cleaning the engine or the front end, with overnight temperature changes, etc. This phenomenon is more visible on lenses made of clear glass than on lenses with patterns. The moisture does not affect the headlight function (light performance) and does not lead to corrosion or other damage to headlight parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 27 number 12-14 dated October 12, 2012. Complaints are reported by the customer regarding electrical features and functions in the vehicle. One or more warning lights on in cluster. The DIS or other displays in cluster are blank. MMI does not function. Windows do not function. LED indicators in various buttons inside the vehicle do not light up. The voltage regulator on the alternator can sporadically fail causing the electrical system to experience too high of voltage. As a result, the affected vehicle electronic components go in to high voltage protection and deactivate sensitive displays and indicators to prevent electrical damage. When an over voltage condition occurs the vehicle electronics and alternator are protected, thus there is no need to replace the entire alternator assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 17 number 12 - 31 dated August 30, 2012. Oil consumption measurement - Repair Authorization (CA). In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil.
NHTSA source summary · Original PDF not reviewed by Recallfolio
complaints are reported by the customer regarding electrical features and functions in the vehicle. One or more warning lights on in cluster. The DIS or other displays in cluster are blank. MMI does not function. Windows do not function. LED indicators in various buttons inside the vehicle do not light up. The voltage regulator on the alternator can sporadically fail causing the electrical system to experience too high of voltage. As a result, the affected vehicle electronic components go in to high voltage protection and deactivate sensitive displays and indicators to prevent electrical damage. When an over voltage condition occurs the vehicle electronics and alternator are protected, thus there is no need to replace the entire alternator assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 12 ? 75 dated October 3, 2012. The outer door seals have become partially detached. Loss of adhesion between the door structure and door seal due to a flaw in the attachment process in production.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL on. DTCs for the cam actuators are stored in ECM memory. After the activation of the cam actuator to change to the other cam profile, the pin of the actuator is pushed back in by the cam. This is confirmed by a voltage impulse, which is registered by the engine control unit and confirms the operation. If this does not happen, or not at the right time, a DTC "implausible signal" is saved in ECM memory. Check the distance of the pin tip of the cam actuator for valve lift system to the camshaft when it is not operated with a gauge. The measurement of the tip to the basic camshaft circle outside of the groove must be taken. If this measurement is 0.9mm, the actuator 06E103697J must be installed. The actuator 06E103697J must only be used, if the measurement is 0.9mm or bigger.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 11 ? 59 dated October 21, 2011. The outer door seals have become partially detached. Loss of adhesion between the door structure and door seal due to a flaw in the attachment process in production.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 85 number 12 ? 08 dated August 17, 2012. Customer may report the front of the passenger floor mat is wet after heavy rains. The flat surface of the fresh air intake may warp over time and cause a gap where it meets with the plenum wall. During heavy rains, water can back up and enter the vehicle through this gap.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 10 - 60 dated September 28, 2010. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: BACK UP CAMERA IMAGE IS INCORRECT OR OFF, TOO BRIGHT, TOO DARK, FUZZY, DISTORTED OR OPAQUE. MODELS AUDI Q5, Q7, A4, A5, A5 CABRIOLET (2009-14), A5, S5 (2008-14), A8 (2010-14) AND A6 (2011-14). *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: WHEN ACTIVATED, THE INSTRUMENT CLUSTER SYSTEM DISPLAY ILLUMINATES BULB OUT WARNING, INDICATING ONE OR BOTH OF REAR MARKER SIDE LIGHTS BURNT OUT. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: WHEN SELECTING REVERSE GEAR, THE PICTURE OF REARVIEW CAMERA FAILS TO APPEAR, SPORADICALLY. CERTAIN MODELS, CAMERA IMAGE CAN BE RE=ACTIVATED. MODEL YEARS 2008-2013. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: CONDENSATION, FROM EVAPORATOR, IS ENTERING FOOTWELL AREA, IN FRONT, BETWEEN BODY AND SEALING SURFACE OF DRAIN HOSE THAT ASSEMBLED BY SUPPLIER INCORRECTLY. MODELS A4, A5 COUPE, Q5 AND A5 CABRIOLET. MY 2009-2011. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: VEHICLE HAVE ISSUES WITH IGNITION KEY CAN NOT BE REMOVED FROM IGNITION; VEHICLE IN PARK POSITION BUT UNABLE TO MOVE SHIFTER; ENGINE SWITCHED OFF BUT REMOTE CONTROL CAN NOT LOCK WITH ADVANCED KEY; PARK IS NOT RECOGNIZED ELECTRICALLY. *PE
Source components: ELECTRICAL SYSTEM:IGNITION · POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT · POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:FLOOR SHIFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: SOME MODEL YEAR VEHICLES MUST HAVE THE SERVICE PART FOR THE AIRBAG CONTROL UNIT CODED AND/OR PARAMETER USING SVM CODE LISTED IN ETKA. MODELS A4, S4, A5, S5, Q5, TT, TTS, A3, PA , C6, A6 PA, D4, A8,C7 A7. *PE
Source components: AIR BAGS · AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: ON CERTAIN MODEL YEAR 2008 TO 2013 VEHICLES, DURING ADJUSTMENT OR REMOVAL, BRAKE LIGHT SENSORS BEING REPLACED ARE DAMAGED, PREVENTING PROPER ANALYSIS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLKSWAGEN: THE MESSAGE 'TIRE PRESSURE SYSTEM MALFUNCTION' APPEARS ON THE INSTRUMENT PANEL. THERE WILL BE A STORED TROUBLE CODE. THIS PROBLEM IS LIKELY CAUSED BY SOFTWARE. *RM
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE ENGINE THERMOSTAT STAYS CLOSE AND MAY CAUSE THE ENGINE TO OVERHEAT. WARNING LIGHTS WILL ILLUMINATE. 2010-2011 MODELS. *RM
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A SEAL INSIDE THE COOLANT PUMP CAN WEAR OUT AND LEAK COOLANT. THIS ALSO CAUSED THE ENGINE LIGHT TO COME ON. *RM UPDATED ON 06/27/2011. *KB
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: RVU (REQUIRED VEHICLE UPDATE) 94E7 REPLACING DRL CONTROL UNITS. ALL DAYTIME RUNNING LIGHT (DRL) LEDS IN ONE HEADLIGHT ASSEMBLY ARE INOPERATIVE. REDESIGN OF DRL CONTROL UNIT ELECTRONICS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: CRACKING NOISES FROM FRONT AXLE. WHILE DRIVING ON UNEVEN ROADS OR WHEN TURNINGTHE STEERING WHEEL OVER THE FULL RANGE, CRACKING NOISES CAN BE HEARD COMING FROM THE FRONT AXLE. THE NOISE COMES FROM THE SUPPORT BRACKET FOR THE TOP OF THE FRONT STRUT. *PE
Source components: STEERING: STEERING WHEEL/HANDLE BAR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: KEY DOES NOT STAY OR ENGAGE IN IGNITION LOCK. ON VEHICLES WITHOUT ADVANCED KEY, THE REMOTE KEYS ARE INOPERABLE. ON VEHICLES WITH ADVANCED KEY, UNLOCKING/LOCKING USING THE DOOR HANDLE AND THE OPENING OF THE TRUNK LID WITH TRUNK HANDLE ARE INOPERABLE; VEHICLE CANNOT BE STARTED WITH START/STOP BUTTON; REMOTE KEYS ARE INOPERABLE. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: DAYTIME RUNNING LIGHTS DO NOT WORK. DAYTIME RUNNING LIGHTS DO NOT WORK ON VEHICLES WITH XENON HEADLIGHTS. THE THUMB WHEEL OR OPTION FOR DAYTIME RUNNING LIGHTS IS TURNED OFF BY MISTAKE. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
REPLACED AIRBAG CONTROL UNIT CANNOT BE CODED. AFTER REPLACING THE AIRBAG CONTROL UNIT, THE CONTROL UNIT CANNOT BE CODED VIA SVM SPEC/ACTUAL. THE LATEST REVISION OF THE AIRBAG CONTROL UNIT MUST BE CODED AND PARAMETERIZED USING AN SVM CODE, WHICH IS LISTED ETKA IN THE REMARKS AREA FOR THE PART NUMBER. *PE
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: MIL ON; ROUGH IDLE; ONE OR MORE OF THE FOLLOWING DTCS ARE STORED-DTC P0300 (RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED); DTC P0301-0312 (CYL. 1 MISFIRE DETECTED-CYL.12 MISFIRE DETECTED); ENGINE MAY HAVE REDUCED PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: TPMS LIGHT ILLUMINATED-REPAIR AUTHORIZATION. THE TPMS WARNING LIGHT IS ILLUMINATED. NO ISSUES HAVE BEEN IDENTIFIED WITH THE ALL NEW INDIRECT TPM SYSTEM. *PE
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: ONE OR MORE DAYTIME RUNNING LIGHT LEDS IN ONE HEADLIGHT ASSEMBLY ARE INOPERATIVE. THERE ARE TWO POSSIBLE CAUSES-LED CIRCUIT BOARD; DRL CONTROL UNIT, LOCATED INSIDE THE HEADLIGHT ASSEMBLY. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: MIL ON; ROUGH IDLE, ONE OR MORE OF THE FOLLOWING DTCS ARE STORED-DTC P0300 RANDOM/MULTIPLE CYLINER MISFIRE DETECTED; DTC P0301-0312 (CYL. 1 MISFIRE DETECTED-CYL. 12 MISFIRE DETECTED); ENGINE MAY HAVE REDUCED PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: SOFTWARE VERSION MANAGEMENT (SVM) OPERATING INSTRUCTIONS. DETAILING THE GENERAL PROCESS FOR CARRYING OUT A SOFTWARE VERSION MANAGEMENT (SVM) SOFTWARE UPDATE FOR ANY TSB OR REQUIRED VEHICLE UPDATE (RVU). TROUBLESHOOTING INFORMATION IS INCLUDED. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: MIL ON AND ONE OR MORE OF THE FOLLOWING DTCS ARE STORED INTHE ECM DATA MEMORY-P310B (LOW PRESSURE FUEL SYSTEM REGULATION, FUEL PRESSURE OUTSIDE TOLERANCE); P129F OR P008B (LOW PRESSURE FUEL SYSTEM, PRESSURE TOO HIGH); P129F OR P008A (LOW PRESSURE FUEL SYSTEM, PRESSURE TOO LOW); P2540 (LOW PRESSURE FUEL SYSTEM, PRESSURE OUT OF RANGE; AND P0087 (RAIL FUEL PRESSURE SYSTEM, PRESSURE TOO LOW). *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: FALSE WARNING BY LANE CHANGE ASSISTANT (AUDI SIDE ASSIST). SOFTWARE FAULT. OPTIMIZED SOFTWARE. REPLACEMENT OF THE CONTROL UNIT IS NOT NECESSARY. WARRANTY CLAIMS FOR CONTROL UNIT REPLACEMENTS WITHOUT USE AND APPLICATION OF THIS TSB WILL BE DEBITED. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: SOFTWARE VERSION MANAGEMENT (SVM), OPERATING INSTRUCTIONS. SVM IS A PROCESS TO UPDATE THE PROGRAMMING IN FLASHABLE (RE-PROGRAMMABLE) CONTROL MODULES AND/OR TO DOCUMENT CHANGES IN SOFTWARE LEVELS IN AUDI VEHICLES. THIS SYSTEM USES THE VAS 5051B OR VAS 5052 DIAGNOSTIC TOOLS TO SEND VEHICLE SPECIFIC DATA TO THE SVM DATABASE, TO DOWNLOAD INSTRUCTIONS FROM THE SVM DATABASE, AND TO FLASH CONTROL UNITS FOR IDENTIFIED SOFTWARE UPDATES. *PE