2012 Audi A6 Manufacturer communications & TSBs.Page 10
Original record summaries, dates and identifiers for this model-year. Records 901–1,000 of 1,501, ordered newest first. Dated records on this page: Nov 14, 2013–Feb 27, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 27, 2014Service Bulletin/Repair Instructions
A871447 2010146-
NHTSA communication ID: 10125561
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 13-62 dated November 21, 2013. Brakes on vehicles produced before September 3, 2012 (calendar week 36 of 2012), squeak or squeal when used with light to moderate force.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when the user searches for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 74 number 13-15 dated November 15, 2013. Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D).
NHTSA source summary · Original PDF not reviewed by Recallfolio
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
Source components: ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 47 number 12-04 dated September 5, 2012. Rattling noises are heard from the front axle when the vehicle is driven over bumpy or rough roads. Poor quality of some retaining springs causes this condition. Functionality of the brakes is not affected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 90 number 13-43 dated December 3, 2013. The seatbelt warning light is illuminated, but the passenger seatbelt is buckled. The seatbelt warning chime is not on. This bulletin only applies to vehicles equipped with navigation system. Software of the instrument cluster control module needs to be updated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 14-67 dated January 21, 2014. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. This TSB should not be used if another brake noise TSB is available for the vehicle. For additional helpful information, refer to the Audi Brake Systems brochure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: THE ENGINE WOULD HAVE A ROUGH IDLE, DIFFERENT MISFIRE FAULTS OR REDUCED PERFORMANCE WITHOUT LOSS OF POWER OR STALLING, THAT CAUSES THE MALFUNCTION INDICATOR LAMP (MIL) ON. MODEL 2008-2015 A3, A4, ALLROAD, TT, A5, A5 CABRIOLET, Q5, A6. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 48 number 13-47 dated August 2, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 09-30 dated April 14, 2009. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 14-59 dated January 21, 2014. The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:BACK UP LIGHTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 14-64 dated January 2, 2014. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 14-55 dated January 8, 2014. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may report that the head-up display (HUD) flickers or dims quickly. Software in the windshield projection head-up display control module, J898 (address word 82), causes incorrect brightness control.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ECM Software Update (FED_EMS)
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM) · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. This Update is in effect until removed.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The NVLD pressure switch may erroneously detect a very small leak. New pressure sensors in production: ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, that are separate (two components): part numbers 8K0906253 and 8K0906253B supersede to 8K0906253D. ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, which are integrated (one component): part numbers 8K0906253A and 8K0906253C supersede to 8K0906253E.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.
Source components: SERVICE BRAKES, HYDRAULIC · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 20 number 13-28 dated November 14, 2013. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the ECM. Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 11-23 dated May 23, 2011. The MIL is on. DTC P169A00 is stored in the ECM. The vehicle is in transport mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The faults listed above are caused by an incorrect software setting and can occur under certain driving conditions. In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The faults listed above are caused by an incorrect software setting and can occur under certain driving conditions. In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The faults listed above are caused by an incorrect software setting and can occur under certain driving conditions. In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-07 dated June 21, 2013. The MIL is on. DTCs are stored in the engine control module (ECM). The faults listed above are caused by an incorrect software setting and can occur under certain driving conditions. In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated. The MIL will illuminate and DTC P112800 and/or DTC P113000 will be stored when the intake air temperature is high. Freeze frame data will show an intake air temperature above 104°F (40°C). The MIL will illuminate and DTC P008700 will be stored when the coolant temperature is high. Freeze frame data will show a coolant temperature above 212°F (100°C). There are no condition restrictions for DTC P244000 or DTC P244200.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 13-11 dated October 31, 2013. When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver?s voice sounds muffled, as if it is being heard from under water. The microphone seal is damaged during installation into the roof module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 57 number 13-87 dated March 27, 2013. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the handle is slack. When fitting the Bowden cable from the mounting bar to the door lock, the cable can get kinked. In some cases, this can increase the inner friction of the strand in the Bowden cable. As a result, the door lock stays in pressed position or does not completely return to its zero position. When the Bowden cable gets twisted during the installation, the rubber grommets can get distorted. Consequently, the Bowden cable has a too-high inner friction and the door lock does not move to the zero position.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-19 dated August 1, 2013. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: SOME VEHICLES WOULD EXPERIENCE ROUGH IDLE, DRIVING POWER REDUCED, ILLUMINATION OF MALFUNCTION INDICATOR LAMP (MIL) ON INSTRUMENT PANEL DUE TO SPECIFIC FAULT CODES PRESENCE. MODEL 2010-2013 A4, A5, A6, Q5. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-35 dated October 8, 2013. During reset of the service reminder, the message ?AIR system - action required - observe test plan? appears on the ODIS tester. MIL is not illuminated. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-37 dated October 10, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION PROVIDED REGARDING WARRANTY EXTENSION ON CARBON BUILDUP REMOVAL, ENGINE CYLINDER HEAD SECONDARY AIR PORTS. MODELS 2009-2012. NO MODEL PROVIDED. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-66 dated January 17, 2013. MIL on. DTCs are stored in the engine control module (ECM). Under extreme driving conditions (such short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incorrect tolerances of cruise control ?Set? button. Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. ?Set? button on cruise control stalk does not work.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The seatbelt warning light is illuminated, but the passenger seatbelt is buckled. The seatbelt warning chime is not on. This bulletin only applies to 2012 vehicles equipped with navigation system. Software of the instrument cluster control module needs to be updated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 27 number 13-17 dated April 5, 2013. Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. ?Set? button on cruise control stalk does not work. DTCs are present in the vehicle. Incorrect tolerances of cruise control ?Set? button.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 13-51 dated July 30, 2013. Brakes on vehicles produced before September 3, 2012 (calendar week 36 of 2012), squeak or squeal when used with light to moderate force.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D). No leak is present. There is a software issue in the seat pneumatics control modules that causes the seat pneumatics to automatically actuate in high altitudes (change in air pressure) or in fluctuating temperatures in order to maintain pressure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
After the engine is switched off, the fuel system creates a natural vacuum as the fuel in the fuel tank cools off. If the natural vacuum leak detection (NVLD) system cannot detect this natural vacuum during the system self-test, the DTC will be stored in the ECM.