Original record summaries, dates and identifiers for this model-year. Records 101–200 of 246, ordered newest first. Dated records on this page: Nov 20, 2019–Aug 25, 2021.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 25, 2021Service Bulletin/Repair Instructions
9003453
NHTSA communication ID: 10218450
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA or 68501446AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, & Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA or 68501448AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
Source components: BACK OVER PREVENTION · FUEL SYSTEM, GASOLINE · POWER TRAIN · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE, TORQUE CONVERTER DRIVE For 3.6L with 62TE NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts (8) 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only (shot peened)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures toFCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE, TORQUE CONVERTER DRIVE For 3.6L with 62TE NOTE: FOR ALL PROMASTER VF 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS Part Number 06511385A$ ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts 8 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only shot peened
NHTSA source summary · Original PDF not reviewed by Recallfolio
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIRROR, Outside Rearview, Includes Mirror Glass For exterior mirror not locking in the correct position or not working, please contact FCA Redacted Content before any replacement. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIRROR, Outside Rearview, Includes Mirror Glass For exterior mirror not locking in the correct position or not working, please contact FCA Redacted Content before any replacement. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIRROR, Outside Rearview, Includes Mirror Glass For exterior mirror not locking in the correct position or not working, please contact FCA Redacted Content before any replacement. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIRROR, Outside Rearview, Includes Mirror Glass For exterior mirror not locking in the correct position or not working, please contact FCA Redacted Content before any replacement. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacyed Content.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacyed Content.
Source components: BACK OVER PREVENTION · FUEL SYSTEM, GASOLINE · POWER TRAIN · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIATOR, Engine Cooling For radiator leak concerns, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please email VIN, dealer code, mileage and picture of the leak to: FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIATOR, Engine Cooling For radiator leak concerns, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please email VIN, dealer code, mileage and picture of the leak to: FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap area
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap area
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HANDLE, Sliding Door, With Cable (External) For a concern of broken external handle on the latch cable attachment, please review opening effort and inspect latch cable routing and take pictures of the latch cable routing and inner side of the handle before removing the broken handle. Please contact FCA Redacted Content to setup part return for analysis If no response in 15 minutes, proceed with repair. Please send pictures to the following: FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
HANDLE, Sliding Door, With Cable (External) For a concern of broken external handle on the latch cable attachment, please review opening effort and inspect latch cable routing and take pictures of the latch cable routing and inner side of the handle before removing the broken handle. Please contact FCA Redacted Content to setup part return for analysis If no response in 15 minutes, proceed with repair. Please send pictures to the following: FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Anti-lock Brake System (ABS) Module Updates This bulletin involves reprogramming the ABS module with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P0731 - Gear Ratio Error In 1st. P0732 - Gear Ratio Error In 2nd. P083B - LC Pressure Switch Rationality. P0841 - L/R Pressure Switch Rationality. P0868 - Line Pressure Low.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Anti-lock Brake System (ABS) Module Updates This bulletin involves reprogramming the ABS module with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P0731 - Gear Ratio Error In 1st. P0732 - Gear Ratio Error In 2nd. P083B - LC Pressure Switch Rationality. P0841 - L/R Pressure Switch Rationality. P0868 - Line Pressure Low.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · SERVICE BRAKES, AIR:ANTILOCK.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP, Power Steering For concern of degraded or loss of power steering assist For US & Canadian Dealers, please email VIN, dealer code, dealer contact info, mileage, picture of steering oil level in resevoir and picture of oil leak in the steering system if present to: FCA Redacted Content For Mexican Dealers, please call FCA Redacted Content at FCA Redacted Content If not response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap areaFig. 1.Check Strap Area Cracking
Source components: AIR BAGS · STRUCTURE · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIATOR, Engine Cooling For radiator leak concerns, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair. Please email VIN, dealer code, mileage and picture of the leak to: FCA Redacted Content; FCA Redacted Content
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap areaFig. 1.Check Strap Area Cracking
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIATOR, Engine Cooling For radiator leak concerns, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair. Please email VIN, dealer code, mileage and picture of the leak to: FCA Redacted Content; FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap areaFig. 1.Check Strap Area Cracking
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIATOR, Engine Cooling For radiator leak concerns, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair. Please email VIN, dealer code, mileage and picture of the leak to: FCA Redacted Content; FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
DETECTOR, Evaporative System Integrity Module (ESIM) Before replacing this part, please call FCA Redacted Content. For Mexican Dealers, please call FCA Redacted Content. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SHAFT, Axle Half, Left/Right If you are working on a Ram ProMaster with a Noisy, Leaking, or Damaged Front Halfshaft/CV Boot, please take a picture of the damage on shaft, ideally prior to removal, and contact Dennis Battle at (734) 231-1540 to have the part returned to FCA via FasTrack. If no response in 15 minutes, proceed with repair.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:SHAFT:INPUT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SHAFT, Axle Half, Left/Right If you are working on a Ram ProMaster with a Noisy, Leaking, or Damaged Front Halfshaft/CV Boot, please take a picture of the damage on shaft, ideally prior to removal, and contact Dennis Battle at (734) 231-1540 to have the part returned to FCA via FasTrack. If no response in 15 minutes, proceed with repair.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.