Original record summaries, dates and identifiers for this model-year. Records 401–500 of 518, ordered newest first. Dated records on this page: Nov 21, 2014–Oct 7, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 7, 2015Service Bulletin/Repair Instructions
68029382A$
NHTSA communication ID: 10216125
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Transmission, Valve Body, Clutch Pack Issue Description: If the vehicle you are repairing exhibits a chirp noise during a 3-4 upshift or a 4-5 upshift please call Jian Zhu on his cell (248) 379-1132 prior to replacing the component. Engineering would like to visit a dealers located in the SE Michigan area with a vehicle exhibiting the above complaint. If Jian cannot be reached within 15 minutes proceed with the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: FLOOR CONSOLE ASSEMBLY Issue Description: Please follow this procedure to resolve Center Floor Console noise (e.g. ticking, buzz, squeak, rattle): 1) Remove tape/film from the Center Floor Console latch areas (Arm Rest Lid latch {Upper compartment} & bezel and Storage Bin {lower compartment} latch & bezel surfaces). 2) Apply interior cleaner onto cloth to remove the tape/film adhesive from the plastic latch & bezel and Storage Bin & Armrest Lid contact surfaces. Verify problem is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Transmission, Valve Body, Clutch Pack Issue Description: If the vehicle you are repairing exhibits a chirp noise during a 3-4 upshift or a 4-5 upshift please call Jian Zhu on his cell (248) 379-1132 prior to replacing the component. Engineering would like to visit a dealers located in the SE Michigan area with a vehicle exhibiting the above complaint. If Jian cannot be reached within 15 minutes proceed with the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: FLOOR CONSOLE ASSEMBLY Issue Description: Please follow this procedure to resolve Center Floor Console noise (e.g. ticking, buzz, squeak, rattle): 1) Remove tape/film from the Center Floor Console latch areas (Arm Rest Lid latch {Upper compartment} & bezel and Storage Bin {lower compartment} latch & bezel surfaces). 2) Apply interior cleaner onto cloth to remove the tape/film adhesive from the plastic latch & bezel and Storage Bin & Armrest Lid contact surfaces. Verify problem is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Title Inspection and return of PN 68210332AA - FUEL PRESSURE SENSOR Start Date: 10/6/2015 7:00 AM End Date Message You are receiving this email as you have been identified to have stock on hand or have stock in transit to your dealership. Reports of dealers receiving incorrect fuel pressure sensors packaged as 68210332AA. Correct and suspect parts can be identified visually by the color of the label on the sensors. Correct sensors have white color label on the part whereas the suspect sensors have yellow colored labels. Reference pictures attached for visual identification. Please inspect stock on hand and return any suspect parts found back to your facing PDC using MRA code 02. Replacement parts can be obtained by reordering the same part number. Direct all questions via email to vn83@chrysler.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
Title Latch Assy. Hood W/AJAR Switch Start Date: 10/6/2015 7:00 AM End Date Message You have been identified as either having stock,or have stock in transit to your dealership. Please return all suspect stock of following part numbers:68159725AB,& 68261143AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02,before 27 O ctober,2015. Return any open orders in process too. Direct all questions via email to MO PARQ C@fcagroup.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illuminates On Rough Roads This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination while driving on rough roads. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0300 - Multiple Cylinder Misfire ? P0301 - Cylinder 1 Misfire ? P0302 - Cylinder 2 Misfire ? P0303 - Cylinder 3 Misfire ? P0304 - Cylinder 4 Misfire ? P0305 - Cylinder 5 Misfire ? P0306 - Cylinder 6 Misfire ? P0307 - Cylinder 7 Misfire ? P0308 - Cylinder 8 Misfire
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
2015 RAM 2500 PICKUP AND 2015 RAM 3500 PICKUP: VEHICLES WITH 5.7L ENGINES, WHILE DRIVING ON ROUGH ROADS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP ILLUMINATION. PROCEDURE ON REPROGRAMMING POWERTRAIN CONTROL MODULE WITH LATEST SOFTWARE *CN
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mopar Trailer Tow Mirror Kit After installing the Mopar Trailer Tow Mirror Kit, configure the vehicle for Trailer Tow mirrors. To do this, add the LEG (Trailer Tow Mirrors) sales code to the VIN using DealerCONNECT and then performing a vehicle re-configuration using the WiTech tool.~ After Kit is completely installed, perform the following;~ 1. Add LEG sales code to the VIN under the ?Vehicle Option Updates? Found on Dealerconnect~ 2. Update Vehicle Configuration by using the WiTech tool and performing ?Restore Vehicle Configuration.?
NHTSA source summary · Original PDF not reviewed by Recallfolio
Spare Tire Kit For vehicles with Alloy Wheels, an adapter is required (not included) to connect the alloy wheel to the spare tire winch cable when storing under the vehicle. The adapter is part number 6824863AA and requires three (3) mounting nuts; PN 68150129AA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rattle/Clunking/Popping Noise While Driving Vehicle On Uneven Roads This bulletin involves replacing the frame to body cushion isolators located under the right and left cab A-pillars. The customer may describe a rattle/clunking noise or popping that can be heard and felt in the floor under the front passenger or driver side when the vehicle is driven on uneven roads, especially from a higher level to a lower level. Noise may be more audible at cold temperature.
Source components: STRUCTURE · STRUCTURE:FRAME AND MEMBERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Unable To Register With Uconnect This bulletin involves retrieving MDN and MEID numbers from the radio. Creating a Star case and recording the MDN and MEID with in the Star Case. The Star center will reply back with an access code that will need to be entered into the radio. The customer may notice that their Uconnect Apps do not work and they can?t register with Uconnect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2014 KL 9-Speed service transaxle with 2015 common hardware This 9-speed transaxle must be ordered thru Mopar?s Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM).~ This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3/RA4 Radio The MY16 RA3/4 radios are susceptible to randomly set an erroneously BCM or IPC ?U0184 - Loss of Com with Radio? fault. The radio should not be replaced for this issue if the fault is stored, if the code cannot be reproduced and no trouble can be found (radio functions properly). In this case it is no impact to the customer in any way. Do NOT replace the radio for this issue. Please contact John Carlesimo at cell (248) 941-8756 if you have any further questions regarding this fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HVAC Blower and Wheel HVAC blower motor is inoperative. Before replacing the blower motor please call one of these individuals:~ First call Brad Bartkowicz at cell (586) 808-4114~ If no answer, then call Vince Celli at cell (586) 630-8136~ If not response in 15 minutes, continue with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HVAC blower assembly Blower Motor either making noise or is inoperative (even intermittently). Before replacing any of the part numbers listed above, please call any of the following people for each vehicle type. (If you don't get an answer within 15 minutes,then proceed with the repair.):~ WD/WK--68224166AB - Front Ken Deneau, cell (248)-765-0288~ 68089094AA - Rear Pat Presti- cell (248) 379-0972~ KL/UF/PF- 68223053AB, 68225055AA Mark Ware, cell (248) 705-3469~ F500- 68093422AB,Matt Sasina, cell (248)-464-4982 or Bryan Bremer cell (248) 429-9014~ RT- 68029719AB - Front, Matt Filipkowski cell (248) 877-9106~ 05183147AA - Rear, Ken Deneau, cell (248)-765-0288
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tire pressure monitoring module Prior to replacing tire pressure monitoring module, for DTC's C151D, C1581, please contact Michael Wang at cell (248) 701-5351. If no response or contact is made within 15 minutes, proceed with repairs as necessary.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shifter - Automatic Trans Before this part is replaced for any issue please call John Grzecki on cell (248) 379- 0969. If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any DTCs identified with the scan tool and document them on the repair order.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel tank Before replacing this part, please call Keith Kerby on his Cell (248) 420-5540 OR Manuel Gandara on cell (248) 622 8109 ~ Mexican Dealers please call Ricardo Lozada at cell +52 1 55 1370 3187. If no return call in 15 minutes, continue with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamp Assembly If the headlamp assembly is being replaced, please also replace the harness attached to the headlamp. Engineering would like to have both parts returned for analysis. Also, please take a picture of the parts and email the picture, a short discription of the issue, and the last 8 digits of the VIN to Brigitte.Wicks@fcagroup.com. Thank you.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Compressor HVAC compressor is inoperative. Before replacing the compressor call FCA Release Engineer Mark Briolat at cell (248) 345-0127. If no response in 15 minutes, continue with the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Transfer Unit Prior to replacing the PTU, please review the following .~ Check if the service 4WD light is intermittent by driving under heavy throttle will produce a C1494-92 DTC, if yes, please call FCA axle engineering and do not replace the PTU. Bruce Michel at cell (248) 260-8641, or Jian Zhu at cell (248) 379- 1132. If neither answers with 15 minutes then proceed with the repair. ~ If the service 4WD light lamp is on steady then replace the Power Transfer Unit.
Source components: POWER TRAIN · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diesel Exhaust Fluid (DEF) Level Sensor Manufacturing Defect This bulletin involves replacing the DEF pump module. A manufacturing defect in the level sensor may have occurred, if the level sensor was built within the time frame listed above. There may be a Malfunction Indicator Lamp (MIL) illuminated. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance. ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Camshaft Position Sensor If replacing a camshaft position sensor for P0340 and/or P0344 fault codes, please review information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
Crankshaft Position Sensor Before replacing this part due to a P0335 fault code, please contact Andrew Acton at cell (248) 421-4130. Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
To announce a VIP LOP Restriction Program on the Multi-Displacement Solenoid (MDS) in an effort to monitor and correct quality issues in a timely and efficient manner
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cruise Control Switch Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery Please call Bob Horn at cell (248) 231-3315 prior to replacing any battery. Please identify battery with the last 8 VIN digits along with the 15 digit Medtronic code from the GR-8 tester. If no response in 15 minutes, continue with the repair. Battery needs to be held and not turned in for core charges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bumper Step Pad Customer may notice the center section of the step pad is not sitting flat. It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pump - Power Steering Hydraulic NOTE: This Tech Tip is for gasoline engine JK vehicles only, manufactured before August 26, 2015. If the power steering pump is being replaced because the power steering fluid flow or pressure readings are below specification, the power steering fluid reservoir and cap assembly should also be replaced. Power steering reservoir and cap assembly 52126151AG or later should be used.
Source components: STEERING · STEERING:ELECTRIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Camshaft Position Sensor If replacing a camshaft position sensor for P0340, P0344, P0345, P0349, P0365, P0369, P0390 or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: ? Intermittently blind spot chime will not turn off (KL vehicles only). ? Enable High Definition (HD) feature, (RA4 radios located in Canada and Mexico). ? Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). ? The Radio may switch from SiriusXM to an AM station by itself. ? Uconnect registration always present, can not remove Uconnect account. ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? VR operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? VR phone button may not work at times. ? Audio muted after AUX device is disconnected. ? VR, ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? SirusXM station information does not update. ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Faster response time when using the Remote Service App (U.S. market only). ? Faster connection time with 911(U.S. market only). ? Keyboard improvements, in the Points Of Interest (POI) section. ? High Definition (HD) radio buffering. ? Spanish translation. ? Radio station, scroll feature. ? D
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES NEED RADIO SOFTWARE UPDATE DUE TO INCORRECT NAVIGATION GUIDANCE EXITING HIGHWAY, TELEPROMPTER FAILS TO APPEAR WHEN VOICE RECOGNITION (VR) BUTTON IS PRESSED, BLIND SPOT CHIME INTERMITTENTLY FAILS TO TURN OFF, PREVIOUS RADIO CAMERA IMAGE IS DISPLAYED BEFORE CURRENT IMAGE. MODEL 2015 CHARGER, RAM 4500, 5500, RAM 3500, 2500, 1500 PICKUP, VIPER, CHEROKEE, CHALLENGER, GRAND CHEROKEE, DURANGO, CHRYSLER 300. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Evaporative System Integrity Monitor switch (ESIM) Prior to replacing this component on a 2015 Dodge Journey (JC), please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Element Assy- Heated Seat If any of the Front Heated Seats are Inoperable. Call Mike Wicker at cell (248) 821- 9350 with the Fault Code, so we can determine true root cause. If your call is not returned within 15 minutes, please continue with the repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Seat belt retractor - rear seat center Prior to ordering this part, call Gary Gebski at (248) 807-5874. If no response in 15 minutes, proceed with ordering the part
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following: ? Blind Spot module beep or chime sound may be heard continuous (KL Only). ? Radio may keep the CAN bus network awake, causing a battery drain. ? Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. ? Not possible to set temperature in degree C using the VR (UK vehicles only). ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? Voice Recognition (VR) operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? Voice Recognition (VR) phone button may not work at times. ? Audio muted after AUX device is disconnected. ? Voice Recognition (VR) , ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Displays correct media, song titles and tracks. ? Incoming calls, audio enhancements (LA, LD and LX Only). ? Audio for strong AM stations. ? VR performance. ? Settings can only be changed in run mode, not ACC. ? Notify user wh
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may lock up. ? Back up display may not turn off. ? Audio mutes. ? Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. ? Touchscreen confirmation beep may be too loud (Grand Cherokee only). ? U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only). Improvements: ? Only allow vehicle settings to be changed in run mode. To help ensure settings are properly saved. ? Always gray out text message soft keys for non-supporting devices. ? Voice Recognition (VR) improved accuracy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG2 Or RJ2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may be locked. ? Backup display may not turn off. ? Audio Mutes. ? Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. ? Touchscreen confirmation beep may be too loud. ? The radio does not allow selection of the Polish language. ? The radio fan continually runs at high speed. ? Customer perception may be the radio fan is too loud. Improvements: ? Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. ? Always gray out text message soft keys for non-supporting devices. ? Voice Recognition (VR) improved accuracy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHRYSLER 2015 JEEP CHEROKEE, RAM 1500 PICKUP- RAM 2500,3500,4500. CUSTOMERS ARE NOT ABLE TO CHANGE TEMP. OF HEATED SEATS , RADIO NOT ALLOWING SELECTION OF PROPER LANGUAGE, RADIO FANS CONTINUE TO RUN AT HIGH SPEED. *LJ UPDATED 10/13/15. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diesel Exhaust Fluid (DEF) Level Gauge Inaccurate Or Stuck This bulletin involves verifying the correct DEF level in the tank and if necessary, replacing the DEF pump module. A small number of customers may comment that their DEF level gauge is stuck for long periods of time or is erratic. The customer may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High.
Source components: BACK OVER PREVENTION · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diesel Exhaust Fluid (DEF) Level Gauge Inaccurate Or Stuck This bulletin involves verifying the correct DEF level in the tank and if necessary, replacing the DEF pump module. A small number of customers may comment that their DEF level gauge is stuck for long periods of time or is erratic. The customer may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U1421 - Implausible Ignition Key Off Time Received. ? P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? 68RFE Transmission Shift Quality Improvements for low speed First to Neutral and Neutral to First (Garage Shifts). ? Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). ? Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. ? Cold idle speed stability improvement. ? Charging system improvements for dual alternator applications. ? Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). ? Fuel Filter Minder calibration changes. ? wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Tire Pressure System Message This bulletin involves replacing all of the Tire Pressure Module (TPM) sensors. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds, and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: ? Enable High Definition (HD) feature, (RA4 radios located in Canada and Mexico). ? Keyboard improvements, in the Points Of Interest (POI) section. ? Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). ? The Radio may switch from SiriusXM to an AM station by itself. ? Uconnect registration always present, can not remove Uconnect account. ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? VR operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? VR phone button may not work at times. ? Audio muted after AUX device is disconnected. ? VR, ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? SirusXM station information does not update. ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? High Definition (HD) radio buffering. ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Making assist calls. ? App functionality and screen displays. ? Displays correct media, song titles and tracks. ? Travel
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auto Headlamp Enhancements This bulletin involves checking Tunnel Detection values and performing a vehicle reconfiguration if needed. The customer may experience when exiting a dark parking structure or dark tunnel the auto headlamps may not turn off. The customer may also experience when driving on an over cast day the auto headlamps may cycle on and off frequently.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may experience one or more of the following: ? Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. ? Touchscreen confirmation beep may be too loud (Grand Cherokee only). ? U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only). Improvements: ? Only allow vehicle settings to be changed in run mode. To help ensure settings are properly saved. ? Always gray out text message soft keys for non-supporting devices. ? Voice Recognition (VR) improved accuracy.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · SEATS · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG2 Or RJ2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may experience one or more of the following: ? Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. ? Touchscreen confirmation beep may be too loud. ? The radio does not allow selection of the Polish language. ? The radio fan continually runs at high speed. ? Customer perception may be the radio fan is too loud. Improvements: ? Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. ? Always gray out text message soft keys for non-supporting devices. ? Voice Recognition (VR) improved accuracy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Tire Pressure System Message This bulletin involves inspecting and replacing the Tire Pressure Module (TPM) sensor if required. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EXTERIOR LIGHTING · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Tire Pressure System Message This bulletin involves inspecting and replacing the Tire Pressure Module (TPM) sensor if required. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Tire Pressure System Message This bulletin involves inspecting and replacing the Tire Pressure Module (TPM) sensor if required. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EXTERIOR LIGHTING · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Tire Pressure System Message This bulletin involves inspecting and replacing the Tire Pressure Module (TPM) sensor if required. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: U0140 Lost Communication With Body Control Module (BCM) This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated (latest available) software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: U0140 Lost Communication With Body Control Module (BCM) This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated (latest available) software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: U0140 Lost Communication With Body Control Module (BCM) This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated (latest available) software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: U0140 Lost Communication With Body Control Module (BCM) This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated (latest available) software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: ? Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. ? Not possible to set temperature in degree C using the VR (UK vehicles only). ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? Voice Recognition (VR) operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? Voice Recognition (VR) phone button may not work at times. ? Audio muted after AUX device is disconnected. ? Voice Recognition (VR) , ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Displays correct media, song titles and tracks. ? Incoming calls, audio enhancements (LA, LD and LX Only). ? Audio for strong AM stations. ? VR performance. ? Settings can only be changed in run mode, not ACC. ? Notify user when messaging features are not supported on certain phones/devices. ? Shows direction and distance for POI when using VR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid. The customer may describe a binding, or audible clicking condition when the center console lid is being opened or closed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated software. During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present. ? U0140 Lost Communication With Body Control Module. (Attempting to clear this DTC will be unsuccessful.) ? P030X Cylinder X Misfire Detected ? P0300 Multiple Cylinder Misfire Detected Additionally the following enhancements have been implemented. ? Potential small improvement in fuel economy at higher altitudes. ? Potential improvement in high altitude engine idle RPM stability.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous cameras image before displaying the current image.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 RA4 Radio Enhancements if required, updating the radio software. A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous cameras image before displaying the current image. Navigation lost vehicle position, during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR, ? Listen? to text, will only play 1st message. Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). SirusXM station information does not update. Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. Display screen show ambient temperature as ?- - ? not normal values.Improvements: High Definition (HD) radio buffering. Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Making assist calls. App functionality and screen displays. Displays correct media, song titles and tracks. Travel Link, Points Of Interest (POI), displaying movies and favorites. Incoming calls, audio enhancements (LA, LD and LX Only). Audio for strong AM stations. VR performance. Settings can only be changed in run mode, not ACC. Notify user when messaging features are not s
Source components: AIR BAGS · ELECTRICAL SYSTEM · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only) The Radio may switch from SiriusXM to an AM station by itself Uconnect registration always present, can not remove Uconnect account Teleprompter does not appear when pressing the Voice Recognition (VR) button VR operation cancels while in media mode Radio may display previous cameras image before displaying the current image Navigation lost vehicle position, during route calculation Navigation displays are missing after vehicle heading changes Navigation giving incorrect guidance to exit the highway FM audio may switch to AM after ignition cycle Text messages appear as sender?s phone number not their name. VR phone button may not work at times Audio muted after AUX device is disconnected VR, ? Listen? to text, will only play 1st message Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only) SirusXM station information does not update. Speed adjusted volume, may not work AM or FM seek or tuner soft keys may be missing Display screen show ambient temperature as ?- - ? not normal values.Improvements: High Definition (HD) radio buffering. Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Making assist calls. App functionality and screen displays. Displays correct media, song titles and tracks. Travel Link, Points Of Interest (POI), displaying movies and favorites. Incoming calls, audio enhancements (LA, LD and LX Only). Audio for strong AM stations. VR performance. Settings can only be changed in run mode, not ACC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Mirror, Outside Rearview Issue Description: Prior to replacing this part for being loose at the head or pivot, perform the following reset procedure. Using the mirror?s push button on the driver switch panel power fold close and open mirror. If the loose condition exists after performing the reset procedure three times, then replace the mirror as required to fix the vehicle. Inform customer that the intended use of the power fold mirrors is by pushing the button to fold and unfold the mirrors. Please educate the customer of the proper operation of the power folding mirrors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Mirror, Outside Rearview Issue Description: Prior to replacing this part for being loose at the head or pivot, perform the following reset procedure. Using the mirror?s push button on the driver switch panel power fold close and open mirror. If the loose condition exists after performing the reset procedure three times, then replace the mirror as required to fix the vehicle. Inform customer that the intended use of the power fold mirrors is by pushing the button to fold and unfold the mirrors. Please educate the customer of the proper operation of the power folding mirrors.
Source components: AIR BAGS · ELECTRICAL SYSTEM · PARKING BRAKE · POWER TRAIN · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Mirror, Outside Rearview Issue Description: Prior to replacing this part for being loose at the head or pivot, perform the following reset procedure. Using the mirror?s push button on the driver switch panel power fold close and open mirror. If the loose condition exists after performing the reset procedure three times, then replace the mirror as required to fix the vehicle. Inform customer that the intended use of the power fold mirrors is by pushing the button to fold and unfold the mirrors. Please educate the customer of the proper operation of the power folding mirrors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud (Grand Cherokee only). U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only).Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG2 Or RJ2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud. The radio does not allow selection of the Polish language. The radio fan continually runs at high speed. Customer perception may be the radio fan is too loud.Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud (Grand Cherokee only). U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only).Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · SEATS · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG2 Or RJ2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud. The radio does not allow selection of the Polish language. The radio fan continually runs at high speed. Customer perception may be the radio fan is too loud.Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud (Grand Cherokee only). U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only).Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG2 Or RJ2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud. The radio does not allow selection of the Polish language. The radio fan continually runs at high speed. Customer perception may be the radio fan is too loud.Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Air Suspension Message Battery Voltage Low This Bulletin involves updating the Air Suspension Control Module (ASCM) software. false message ?Battery Voltage Low - Start Engine to Change Ride Height? which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Air Suspension Message Battery Voltage Low This Bulletin involves updating the Air Suspension Control Module (ASCM) software. false message ?Battery Voltage Low - Start Engine to Change Ride Height? which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.