Original record summaries, dates and identifiers for this model-year. Records 101–200 of 856, ordered newest first. Dated records on this page: Dec 10, 2024–Sep 18, 2025.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 18, 2025Service Bulletin/Repair Instructions
23-008-25 REV. A
NHTSA communication ID: 11023326
NHTSA source summary · Original PDF not reviewed by Recallfolio
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Axle Vibration Shudder Or Chatter Customers may experience the following: ● A chatter, shudder, or vibration from the rear axle during turns. NOTE: This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axle fluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components. NOTE: This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every 3 years or 30,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual. This bulletin involves changing the rear axle lube to possibly address a chatter, shudder or vibration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
NHTSA source summary · Original PDF not reviewed by Recallfolio
115V Power Outlet LED Always On The amber LED remains continuously illuminated, regardless of whether the switch button is activated. This bulletin involves replacing the inverter switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Telematics Box Module (TBM) Over The Air Software Update From 5.39.1 To 5.65 Customers may experience the following: ● 'SOS unavailable' popup message. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.
NHTSA source summary · Original PDF not reviewed by Recallfolio
To inform dealers about the 850RE valve body PN: R8348504A connector: the original 16-pin connector included six pins that were not used in this application. To simplify the design, the connector has been optimized and updated to a 10-pin configuration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
8HP75 D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on the following: ● Vehicle enter limp home mode. This bulletin involves replacing the D clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
850RE D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Bumper Paint Is Dull Customers may comment on the following: ● Front bumper paint is dull Fig. 1 This bulletin involves inspecting and possibly replacing the front bumper.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frequent Repairs Of Fuel System Components Such As Fuel Filters Numerous Stellantis vehicles having fuel line components replaced such as diesel fuel filters. Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Global Telematics Box Module Over The Air Update from 5.39.1 to 5.65 TBM2.0 Software Version (FOTA) Customers may experience one or more of the following: - Error display of ""Uconnect Box Requires Service/Wifi Unavailable"" popups; [ TBM DTC B22A9-96 Internal Performance Failure ]. - Error display of ""Uconnect Box Requires Service"" pop-ups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ]."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Frequent Repairs Of Fuel System Components Such As Fuel Filters Numerous Stellantis vehicles having fuel line components replaced such as fuel filter. Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Frequent Repairs Of Fuel Line Components Such As Fuel Filters Numerous Stellantis vehicles having fuel line components replaced such as fuel filter. Occasionally, components are replaced before their standard life expectancy or when not contaminated with debri "
NHTSA source summary · Original PDF not reviewed by Recallfolio
LAMP Courtesy/Ambient Courtesy / Ambient Lamp: Light guide not fully seated into the retainer during IP sub-assembly due to inconsistent operator installation effort, leading to latent BSR issue that manifests under customer usage conditions. Solution: remove and reinstall light guide to be fully seated in the bracket retainer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission "Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"DISPLAY Order regular part number for New unsold and Warranty units only. Verify Z part number availability. Order a Z part number for all Exchange Orders: Mopar, customer pay and service contract."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on the following: ● Vehicle enter limp home mode. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Rear Propshaft clunk Customers may experience the following: ● A clunk noise from the driveshaft while coming to a stop or when just starting to tip into throttle at take off This bulletin involves inspecting and possibly reprogramming the ISCM and the Powertrain Control Module (PCM) with the latest available software. *This bulletin involves greasing the rear driveshaft and installing a boot kit"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Kit For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Front Lower Control Arm Stabilizer Link Noise Customers may experience the following: ● Rattle or clunk noise coming from the front end of the vehicle when driving over bumps, performing turns or during normal operation. This bulletin involves road testing and possibly tightening the stabilizer link attachment to lower control arm nut. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Oil Leaking From Oil Filter Area Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: ● Oil found on the ground beneath the vehicle. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. "
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Clicking Noise While In 4WD Customers may experience the following: ● Ratcheting, click, or clicking noise in 4WD while turning. This bulletin involves replacing the front driveshaft."
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Clicking Noise While In 4WD ustomers may experience the following: ● Ratcheting, click, or clicking noise in 4WD while turning. his bulletin involves replacing the front driveshaft"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
SWITCH Headlamp Before replacing the Headlamp Switch for faulty dimmer operation. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
ARM Lower Control WHAT: Clunking noise from Front Stabar link to Front Lower Control Arm (FLCA). WHY: The joint is coming loose due to loss of clamp load when there is embedment on FLCA mating surface to the stabar link ball stud. We are currently updating the stabar link design and new design will be implemented in March 2025. HOW: If this Front stabar link to FLCA joint torque is under the residual torque of 70Nm, please retorque the joint to this spec of 110 (Min 70-Max 138). Otherwise proceed with regular diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
ARM Lower Control WHAT: Clunking noise from Front Stabar link to Front Lower Control Arm (FLCA). WHY: The joint is coming loose due to loss of clamp load when there is severe embedment on FLCA mating surface to the stabar link ball stud. We are currently updating the stabar link design and new design will be implemented in March 2025. HOW: If this Front stabar link to FLCA joint torque is under the residual torque of 70Nm, please retorque the joint to this spec of 110 (Min 70-Max 138). Otherwise proceed with regular diagnosis.