Original record summaries, dates and identifiers for this model-year. Records 301–400 of 590, ordered newest first. Dated records on this page: Feb 26, 2016–Sep 7, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 7, 2016Service Bulletin/Repair Instructions
05152029
NHTSA communication ID: 10223855
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.].
NHTSA source summary · Original PDF not reviewed by Recallfolio
Foil Patch If you are replacing the headliner for a 2014 or 2015 Ram 1500, you must also order patch kit PN 68315885AA to replace the foil patch for recall R47.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Foil Patch If you are replacing the headliner for a 2014 or 2015 Ram 1500, you must also order patch kit PN 68315885AA to replace the foil patch for recall R47.
Source components: STRUCTURE · STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console If vehicle comes in for squeaking, clicking, or binding of the center console lid, verify the complaint by cycling the upper console lid. Check for a green dot sticker on the back of the console behind the rear panel by the hinge. ~ If the above complaint is verified and the console DOES NOT have a green dot sticker near the hinge (behind the back panel), order kit PN 68315574AA and install per the included instructions. Otherwise continue with the repair. Please reference TSB 23-001-16 Rev. E (or later version).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tailgate Contacting Pickup Box Panel When Closing This bulletin involves adjusting the passenger side outer box flange. The customer may describe the tailgate making contact with the passenger side outer box panel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tailgate Contacting Pickup Box Panel When Closing This bulletin involves adjusting the passenger side outer box flange. The customer may describe the tailgate making contact with the passenger side outer box panel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tailgate Contacting Pickup Box Panel When Closing This bulletin involves adjusting the passenger side outer box flange. The customer may describe the tailgate making contact with the passenger side outer box panel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
P/N 68111384AB: Inspect &Return: Switch - Speed Control You have been identified as either having stock, or have stock in transit to your dealership. Please return parts which have a pacakging date code of July 20th 2016. Reference pictures attached for suspect part identification. Please return parts backto your facing depot using Return Code 02, before 31 August, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
05187880AC - Inspect and Return: Relay Assy - Heater Intake Air You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Inspect and Return: Lamp Assy - Tail Light Rt/L You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of following part numbers: 68110016AC, 68110016AD, 68110016AE, 68110017AD, 68236104AC, 68236105AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31 August, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
P/N 04573460 - Inspect &Return: Rocker Assy - Intake Valve RT You have been identified as either having stock, or have stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
68103256AGReturn: Line Assy - A/C Suction and Liquid You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number 68103256AG packaged before 2016/08/01. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
68160775AB: Inspect and Return: Switch - Outside Door Handle You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68160775AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 26 August, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tailgate controller If the vehicle is in for tailgate issue on all RAMs 2014, 2015, 2016 MY, FCA is looking to gather information prior to repairing the vehicle. Please contact Jim Smith via Cell Phone (248) 765-8972 If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tailgate controller If the vehicle is in for tailgate issue on all RAMs 2014, 2015, 2016 MY, FCA is looking to gather information prior to repairing the vehicle. Please contact Jim Smith via Cell Phone (248) 765-8972 If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TANK, Diesel Exhaust Fluid, Part Includes Temp Sensor and Level Sensor For DS and WK vehicles ONLY; If the urea tank is being replaced due to P249C or P203E on a 2014-2016 model year 3.0L Turbo Diesel (EXF) on DS or WK, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bumper Step Pad Customer may notice the center section of the step pad is not sitting flat. It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Mihaela Colfescu via cell (248) 841-5736 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Mihaela would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Mihaela does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to mihaela.colfescu@fcagroup.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG3 RG4 RJ3 RJ4 Radio EnhancementsThis bulletin involves inspecting and if required, updating the radio software.A small number of customers may experience one or more of the following: · Blind Spot module beep or chime sound may be heard continuously (KL Only). · Radio may keep the CAN bus network awake, causing a battery drain. · Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature.· Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). · Teleprompter does not appear when pressing the VR button.· VR operation cancels while in media mode. · Radio may display camera?s previous image before displaying the current image. · Navigation lost vehicle position during route calculation. · Navigation displays are missing after vehicle heading changes. · Navigation giving incorrect guidance to exit the highway. · FM audio may switch to AM after ignition cycle. · Text messages appear as sender?s phone number not their name. · VR phone button may not work at times. · Audio muted after AUX device is disconnected. · VR ?Listen? to text will only play 1st message. · Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). · Speed adjusted volume may not work.· AM/FM seek or tuner soft keys may be missing.· Display screen shows ambient temperature as ?- - ? not normal values. Improvements:· **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect.Improvements:· **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect.· HVAC temperature out of sync with radio display (KL Only).** · Spanish translation. · Radio station, scroll feature. · Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). · Displays correct media, song titles and tracks. · Incoming calls, audio enhance
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear seat fold latches If the rear seat is difficult to fold or binds, please contact Trevor Trudell at cell (248) 420-7340 before making any repair. If no response within 15 minutes please proceed with the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Seat Adjuster Assemblies If the seat has a squeak or rattle, and it is reproducible, please call Trevor Trudell at cell (248) 420-7340 before any work is performed. If no response within 15 minutes please proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Pedal Sensor For DS, WD & WK bodies ONLY; Prior to replacing the brake sensor; Please call Salma Al Ryahi at cell (519) 992-7293. If you are unable to get a response within 15 minutes, please take a picture that shows the sensor side together with the plunger and continue with normal repair procedure.
Source components: SERVICE BRAKES, HYDRAULIC · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Anti-Lock Brake Module (ABS) For 2015 and 2016 DS ONLY; Before replacing the ABS module, please call Brittany Potton at cell (248) 494-1087. If you don't receive response within 15 minutes, please continue with normal repair procedure.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Anti-Lock Brake Module (ABS) For 2015 and 2016 DS ONLY; Before replacing the ABS module, please call Brittany Potton at cell (248) 494-1087. If you don't receive response within 15 minutes, please continue with normal repair procedure.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ANTI-LOCK BRAKE MODULE (ABS) FOR 2015 AND 2016 DS ONLY; BEFORE REPLACING THE ABS MODULE, PLEASE CALL BRITTANY POTTON AT CELL (248) 494-1087. IF YOU DON'T RECEIVE RESPONSE WITHIN 15 MINUTES, PLEASE CONTINUE WITH NORMAL REPAIR PROCEDURE."
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68143886AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68174065AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 04685719AI. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Axle Assembly, Axle Carrier, Axle Ring and Pinion Engineering is currently investigating concerns with pinion seals on the 2014-15 MY Ram 1500 Pick-up with a rear axle manufactured within the October to November 2014 calendar year. Please contact Ridhan Riyal at cell (810) 513-3832 for further instruction. If he cannot be reached with 15 minutes proceed with your repair.~ The DS Limited Slip Differential operates as a torque sensing device because when torque is applied to the differential gear set the reaction forces of the bevel gears apply an axial force into the clutch system providing the torque bias. When the input torque is very low the reaction forces will decrease allowing the differential to ACT SIMILIAR TO A OPEN DIFFERENTIAL (zero preload). Please do not confuse this with prior model year Limited Slip Differentials. See the service manual for complete details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Axle Assembly, Axle Carrier, Axle Ring and Pinion Engineering is currently investigating concerns with pinion seals on the 2014-15 MY Ram 1500 Pick-up with a rear axle manufactured within the October to November 2014 calendar year. Please contact Ridhan Riyal at cell (810) 513-3832 for further instruction. If he cannot be reached with 15 minutes proceed with your repair.~ The DS Limited Slip Differential operates as a torque sensing device because when torque is applied to the differential gear set the reaction forces of the bevel gears apply an axial force into the clutch system providing the torque bias. When the input torque is very low the reaction forces will decrease allowing the differential to ACT SIMILIAR TO A OPEN DIFFERENTIAL (zero preload). Please do not confuse this with prior model year Limited Slip Differentials. See the service manual for complete details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 68141880AH, 68141881AH, 68145625AI, 68145626AI, 68189480AF and replacement part numbers are 68141880AI, 68141881AI, 68145625AJ, 68145626AJ & 68189480AG respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part number: 05278632AF and replacement part number is 52030379AA which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 1YG06JSCAC, 1YG06KEPAC, 1YG 06KFSAC, 1YG 06KGZAC, 1YG 06KBUAC and replacement part numbers are 1YG 1YG06KFSAD, 1YG 06KG ZAD, 1YG 06KBUAE respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part number: 68188889AE and replacement part number is 68188889AF which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Return: ALTERNATOR - ENGINE You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"AXLE ASSEMBLY, AXLE CARRIER, AXLE RING AND PINION ENGINEERING IS CURRENTLY INVESTIGATING CONCERNS WITH PINION SEALS ON THE 2014-15 MY RAM 1500 PICK-UP WITH A REAR AXLE MANUFACTURED WITHIN THE OCTOBER TO NOVEMBER 2014 CALENDAR YEAR. PLEASE CONTACT RIDHAN RIYAL AT CELL (810) 513-3832 FOR FURTHER INSTRUCTION. IF HE CANNOT BE REACHED WITH 15 MINUTES PROCEED WITH YOUR REPAIR.~ THE DS LIMITED SLIP DIFFERENTIAL OPERATES AS A TORQUE SENSING DEVICE BECAUSE WHEN TORQUE IS APPLIED TO THE DIFFERENTIAL GEAR SET THE REACTION FORCES OF THE BEVEL GEARS APPLY AN AXIAL FORCE INTO THE CLUTCH SYSTEM PROVIDING THE TORQUE BIAS. WHEN THE INPUT TORQUE IS VERY LOW THE REACTION FORCES WILL DECREASE ALLOWING THE DIFFERENTIAL TO ACT SIMILIAR TO A OPEN DIFFERENTIAL (ZERO PRELOAD). PLEASE DO NOT CONFUSE THIS WITH PRIOR MODEL YEAR LIMITED SLIP DIFFERENTIALS. SEE THE SERVICE MANUAL FOR COMPLETE DETAILS."
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of following part numbers: 68036213AA, 68036230AF, 68158196AC, 68158197AD, & 68158454AD. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
68085119AE,Inspect and Return: Exhaust Pipe Assy - Frt W/Catalytic Converter You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Integrated Center Stack If vehicle is found within 50 mile radius of the Detroit Metro area please hold vehicle and contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Compressor This applies to 2015 and 2016 UF and PF. Before replacing the AC compressor for noise, leaks , or in-op:~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Module - CTM ? Peiker For RT, JK and MK bodies only; Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery - Transmitter For vehicles within 12 Months in Service which have a "FOB Battery Low" message within Cluster or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding.
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
Source components: ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
Source components: PARKING BRAKE · POWER TRAIN · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. **This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. **This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. **This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
TANK, Diesel Exhaust Fluid, Part Includes Temp Sensor and Level Sensor If the urea tank is being replaced due to P249C on a 2014-2016 model year 3.0L Turbo Diesel (EXF) DS truck, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair.~
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:UREA INJECTION SYSTEM (DEF).
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXF long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TANK, Diesel Exhaust Fluid, Part Includes Temp Sensor and Level Sensor If the urea tank is being replaced due to P249C on a 2014-2016 model year 3.0L Turbo Diesel (EXF) DS truck, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXF long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. As per regulatory compliance: Please return follow ing stock of part numbers: 82214711, 82214712, 82214713, 82214714, 82214715, 82214716, 82214717, 82214718, 82214720, 82214721, 82214722, 82214723, 82214724, 82214725, 82214726, 82214727, 82214728, 82214729, 82214730, 82214731, 82214732. Please return parts back to your facing depot using Return Code 02, before 31May, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXG long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXG long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of part number 68288760AA. Replacement part number is 68288760AB. Replacement parts w ill be available w eek ending 5/6/16. Please return suspect parts back to your facing depot using Return Code 02, before 26 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 68003062AB, 68003083AB, 68003085AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1PE001W 7AB, 1PE011W 7AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification R51 Winter Front Cover The Charge Air Cooler (CAC) on about 8,000 of the above vehicles may develop internal icing in cold temperature regions. This condition may cause the Malfunction Indicator Light (MIL) to illuminate and cause the vehicle to experience a 35 mph limp in condition. A winter front cover must be installed when sustained day and night time temperatures drop below 30° F (-1° C).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification R51 Winter Front Cover The Charge Air Cooler (CAC) on about 8,000 of the above vehicles may develop internal icing in cold temperature regions. This condition may cause the Malfunction Indicator Light (MIL) to illuminate and cause the vehicle to experience a 35 mph limp in condition. A winter front cover must be installed when sustained day and night time temperatures drop below 30° F (-1° C).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: RA3/RA4 Radio Software Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · **Poor or no connection to cellular network (U.S. market only). · HVAC temperature out of sync with radio display (KL vehicles).** · Intermittently blind spot chime will not turn off (KL vehicles only). · Enable High Definition (HD) feature (RA4 radios located in Canada and Mexico). · Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). · The Radio may switch from SiriusXM to an AM station by itself. · Uconnect registration always present, can not remove Uconnect account. · Teleprompter does not appear when pressing the Voice Recognition (VR) button. · VR operation cancels while in media mode. · Radio may display previous image before displaying the current image. · Navigation lost vehicle position during route calculation. · Navigation displays are missing after vehicle heading changes. · Navigation giving incorrect guidance to exit the highway. · FM audio may switch to AM after ignition cycle. · Text messages appear as sender?s phone number not their name. VR phone button may not work at times. · Audio muted after AUX device is disconnected. · VR, ? Listen? to text will only play first message. · Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). · Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). · SirusXM station information does not update. · Speed adjusted volume, may not work. · AM or FM seek or tuner soft keys may be missing. · Display screen show ambient temperature as ?- - ? not normal values. Improvements: · **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. · Ability to press VR button for more than one second.**
Source components: AIR BAGS · ELECTRICAL SYSTEM · LANE DEPARTURE · PARKING BRAKE · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: RA3/RA4 Radio Software Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · Poor or no connection to cellular network (U.S. market only). · HVAC temperature out of sync with radio display (KL vehicles).** · Intermittently blind spot chime will not turn off (KL vehicles only). · Enable High Definition (HD) feature (RA4 radios located in Canada and Mexico). Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. · Uconnect registration always present, can not remove Uconnect account. · Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. · Radio may display previous image before displaying the current image. · Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. · FM audio may switch to AM after ignition cycle. · Text messages appear as sender's phone number not their name. VR phone button may not work at times. · Audio muted after AUX device is disconnected. · VR, Listen, to text will only play first message. · Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). · Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). · SirusXM station information does not update. · Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. · Display screen show ambient temperature as ?- - ? not normal values. Improvements: · **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. · Ability to press VR button for more than one second.** · Faster response time when using the Remote
Source components: ELECTRICAL SYSTEM · EQUIPMENT · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Air Suspension Control Module (ASCM) This bulletin involves updating the ASCM with the latest available software. Customers may experience no ride height change with the vehicle in real cold conditions and in addition they may also have a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · C15A1-00 - Unable To Obtain Desired Ride Height. · C1562-98 - Ride Height Air Pump Control - Component Or System Over Temperature. · C1562-92 - Height Air Pump Control - Performance Or Incorrect Operation. · C159F-92 - Air Suspension Reverse Valve 1 Control - Performance Or Incorrect Operation. · C15A0-92 - Air Suspension Reverse Valve 2 Control - Performance Or Incorrect Operation. · C155E-92 - Height Pressure Vent Control - Performance Or Incorrect Operation. · C15AA-00 - Air Leak During Vent. In addition, the customer may notice the following condition: · Vehicle does not change ride heights when selected in cold weather.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Air Suspension Control Module (ASCM) This bulletin involves updating the ASCM with the latest available software. Customers may experience no ride height change with the vehicle in real cold conditions and in addition they may also have a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · C15A1-00 - Unable To Obtain Desired Ride Height. · C1562-98 - Ride Height Air Pump Control - Component Or System Over Temperature. · C1562-92 - Height Air Pump Control - Performance Or Incorrect Operation. · C159F-92 - Air Suspension Reverse Valve 1 Control - Performance Or Incorrect Operation. · C15A0-92 - Air Suspension Reverse Valve 2 Control - Performance Or Incorrect Operation. · C155E-92 - Height Pressure Vent Control - Performance Or Incorrect Operation. · C15AA-00 - Air Leak During Vent. In addition, the customer may notice the following condition: · Vehicle does not change ride heights when selected in cold weather.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: Flash: Air Suspension Control Module (ASCM) This bulletin involves updating the ASCM with the latest available software. SYMPTOM/CONDITION: Customers may experience no ride height change with the vehicle in real cold conditions and in addition they may also have a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · C15A1-00 - Unable To Obtain Desired Ride Height. · C1562-98 - Ride Height Air Pump Control - Component Or System Over Temperature. · C1562-92 - Height Air Pump Control - Performance Or Incorrect Operation. · C159F-92 - Air Suspension Reverse Valve 1 Control - Performance Or Incorrect Operation. · C15A0-92 - Air Suspension Reverse Valve 2 Control - Performance Or Incorrect Operation. · C155E-92 - Height Pressure Vent Control - Performance Or Incorrect Operation C15AA-00 - Air Leak During Vent. In addition, the customer may notice the following condition: Vehicle does not change ride heights when selected in cold weather.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: Flash: Air Suspension Control Module (ASCM) OVERVIEW: This bulletin involves updating the ASCM with the latest available software. SYMPTOM/CONDITION: Customers may experience no ride height change with the vehicle in real cold conditions and in addition they may also have a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · C15A1-00 - Unable To Obtain Desired Ride Height. · C1562-98 - Ride Height Air Pump Control - Component Or System Over Temperature. · C1562-92 - Height Air Pump Control - Performance Or Incorrect Operation. · C159F-92 - Air Suspension Reverse Valve 1 Control - Performance Or Incorrect Operation. · C15A0-92 - Air Suspension Reverse Valve 2 Control - Performance Or Incorrect Operation. · C155E-92 - Height Pressure Vent Control - Performance Or Incorrect Operation. C15AA-00 - Air Leak During Vent. In addition, the customer may notice the following condition: Vehicle does not change ride heights when selected in cold weather.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. The customer may describe a binding or audible clicking condition when the center console lid is being opened or closed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Before replacing the ABS module for a wheel speed sensor fault(s) listed below, please call Brittany Potton at cell (248) 494-1087. If you don't receive response within 15 minutes, please continue with normal repair procedure.~ Possible wheel speed sensor faults: ~ C0030-02 Left Front Tone Wheel-General Signal Failure~ C0031-1D Left Front Wheel Speed Sensor-Circuit Current Out of Range~ C0031-2F Left Front Wheel Speed Sensor-Signal Erratic~ C0031-62 Left Front Wheel Speed Sensor-Signal Compare Failure~ ~ C0033-02 Right Front Tone Wheel-General Signal Failure~ C0034-1D Right Front Wheel Speed Sensor-Circuit Current Out of Range~ C0034-2F Right Front Wheel Speed Sensor-Signal Erratic~ C0034-62 Right Front Wheel Speed Sensor-Signal Compare Failure~ ~ C0036-02 Left Rear Tone Wheel-General Signal Failure~ C0037-1D Left Rear Wheel Speed Sensor-Circuit Current Out of Range~ C0037-2F Left Rear Wheel Speed Sensor-Signal Erratic~ C0037-62 Left Rear Wheel Speed Sensor-Signal Compare Failure~ ~ C0039-02 Right Rear Tone Wheel-General Signal Failure~ C003A-1D Right Rear Wheel Speed Sensor-Circuit Current Out of Range~ C003A-2F Right Rear Wheel Speed Sensor-Signal Erratic~ C003A-62 Right Rear Wheel Speed Sensor-Signal Compare Failure~
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Before replacing the ABS module for a wheel speed sensor fault(s) listed below, please call Brittany Potton at cell (248) 494-1087. If you don't receive response within 15 minutes, please continue with normal repair procedure.~ Possible wheel speed sensor faults: ~ C0030-02 Left Front Tone Wheel-General Signal Failure~ C0031-1D Left Front Wheel Speed Sensor-Circuit Current Out of Range~ C0031-2F Left Front Wheel Speed Sensor-Signal Erratic~ C0031-62 Left Front Wheel Speed Sensor-Signal Compare Failure~ ~ C0033-02 Right Front Tone Wheel-General Signal Failure~ C0034-1D Right Front Wheel Speed Sensor-Circuit Current Out of Range~ C0034-2F Right Front Wheel Speed Sensor-Signal Erratic~ C0034-62 Right Front Wheel Speed Sensor-Signal Compare Failure~ ~ C0036-02 Left Rear Tone Wheel-General Signal Failure~ C0037-1D Left Rear Wheel Speed Sensor-Circuit Current Out of Range~ C0037-2F Left Rear Wheel Speed Sensor-Signal Erratic~ C0037-62 Left Rear Wheel Speed Sensor-Signal Compare Failure~ ~ C0039-02 Right Rear Tone Wheel-General Signal Failure~ C003A-1D Right Rear Wheel Speed Sensor-Circuit Current Out of Range~ C003A-2F Right Rear Wheel Speed Sensor-Signal Erratic~ C003A-62 Right Rear Wheel Speed Sensor-Signal Compare Failure~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pump - vacuum For DS vacuum pump concerns only; If the vacuum pump continues to run even when the ignition is off; before replacing vacuum pump, please call Tim Parks on cell (248) 245-9395 or Fernando Betancourt on cell (248) 202-7871. If you do not receive a return call within 15 minutes, proceed with the repair.~
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pump - vacuum For DS vacuum pump concerns only; If the vacuum pump continues to run even when the ignition is off; before replacing vacuum pump, please call Tim Parks on cell (248) 245-9395 or Fernando Betancourt on cell (248) 202-7871. If you do not receive a return call within 15 minutes, proceed with the repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Inspect and Return: Latch Seat, and Latch Seat Back You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of following part numbers: 68050625AA, 68050626AA, 68050627AA, 68050628AA, 68050743AA, 68050744AA, 68050839AA, 68050841AA, 68257133AA, 68257134AA, 68264578AA, 68264579AA, 68264580AA, 68264581AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 April, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RE2 RE6 RB5 RB6 Radio Software Enhancements This bulletin involves updating the radio software and navigation if equipped. A customer may experience one or more of the following conditions: · Radio display screen will lock up and reset intermittently. · Incorrect routing directions to fuel stations when using Travel Link. · Unable to turn on heated seats; icon is greyed out. · Navigation screen goes blank. · Navigation system freezes/locks up. · Vehicles with Mopar special edition radio will update radio?s splash screen. · Navigation icon shows the vehicle going backward when it?s moving forward.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory:
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mirror, Outside Rearview Replacement outside rearview mirror assembly comes equipped with Turn Signal and Auxiliary (Puddle) Light. If Turn Signal/Puddle Lamp is visually different from OE, you will need to swap the original lamp to the new mirror unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bumper Kit If you are ordering a Center Console bumper kit to repair a vehicle for TSB 23-001- 16 or RRT 16-011 and you receive kit PN 68315574AA, discard the instruction sheet shipped with the kit and reference TSB 23-001-16 REV. B for correct bumper installation instructions. ~ Note: This only applies to the AA level of the kit