Original record summaries, dates and identifiers for this model-year. Records 201–300 of 590, ordered newest first. Dated records on this page: Sep 14, 2016–Oct 10, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 10, 2019Service Bulletin/Repair Instructions
09-003-19
NHTSA communication ID: 10168448
NHTSA source summary · Original PDF not reviewed by Recallfolio
GEN-2 and GEN-3 - 3.0L Oil Filter Cartridge Identification Differences This bulletin highlights the design differences in the oil filter cartridges used in the GEN-2, and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application. Although similar in design, the oil filter cartridges used on the GEN-2 and GEN-3 3.0L diesel engines are different in design. Interchanging them may result in premature engine damage over time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash Over The Air (FOTA) Software Update RA3 and RA4 Radio This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONDENSER, Air Conditioning If it is determined that the A/C compressor does not engage due to a refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet.
Source components: ELECTRICAL SYSTEM · ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Transmission Shift Interlock (BTSI) Please contact Stacey Davis at (248) 260-6078 or stacey.davis@fcagroup.com if the following scenario occurs; The T79 or U11 recall was completed where the shifter inspection was acceptable and the software flash was performed but then the customer comes back needing the BTSI bracket replaced for coming out of park without the brake or key.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Job aid - If you have a suspected TC shudder/vibration, check the Interactive Network for Service Bulletins for the vehicle you are working on. A test-drive snap shot may help you isolate the source of the issue.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play first message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient tempe
Source components: AIR BAGS · BACK OVER PREVENTION · ELECTRICAL SYSTEM · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following: Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play first message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient temperature as ?- - ? not n
Source components: AIR BAGS · BACK OVER PREVENTION · ELECTRICAL SYSTEM · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Trans Oil Pan, Heater Tube or O-ring, Heater Applies to vehicles equipped with 8 speed transmissions only; If you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hub & Bearing Assy - Front For issues with front wheel Hub/Bearings appearing to leak grease, do not replace the parts. Please call Paul Kuehl for further assistance, at cell (248) 535-7013. If no response in 15minutes, proceed with repair, but do not replace bearing(s) unless there is visible damage, see Service Manual Diagnostic Procedure which includes a picture of typical bearing grease weepage.
Source components: EQUIPMENT · POWER TRAIN · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 and RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Thermal Expansion Valve (TXV), H-valve For D trucks only; When diagnosing an A/C system leak at the TXV (Thermal Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Wheel Liner to Steel Bumper Slip Fit Design This bulletin involves informing technicians that the wheel liners tabs are to be tucked behind the flange of the bumper bracket. No fasteners are used to attach the liner and the bumper when vehicle is equipped with a steel front bumper.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing.
Source components: AIR BAGS · BACK OVER PREVENTION · ELECTRICAL SYSTEM · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display cameras previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as senders phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR Listen to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: RA3/RA4 Radio Software Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following: ? **?Navigation Failed? message is displayed. ? Navigation is inoperative or inaccurate. ? CD player will not play songs and/or locks up the radio. ? The clock will not automatically update to local time. ? The clock may be off by several hours (RA3 only). ? HVAC temperature out of sync with radio display (KL vehicles). ? Some Uconnect App remote commands do not execute with the vehicle. ? Radio Apps are inoperative. ? Radio will lock up. Radio display screen is black or blank. Battery drain due to radio staying on.** Rearview Camera image appears jittery (UF vehicles only). Inability to establish a WiFi connection when security feature is enabled (UF vehicles only). Audio distortion/popping heard while playing Apple devices through the USB port (UF vehicles only). Remote Uconnect Apps functions (i.e. door locks, remote start) inoperative while the engine is running (UF vehicles only). HVAC temperature out of sync with radio display (KL vehicles). Intermittently blind spot chime will not turn off (KL vehicles only). The radio may switch from SiriusXMT to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Audio muted after AUX device is disconnected. In addition, the following Improvements are included: **Adds Apple SiriT Eyes Free capability for iPhoneT owners. Add the ability to drag and drop icons into the menu bar. Auto Play can now be configured. Enhanced VR performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (YelpT, PandoraT, AhaT, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: RA3/RA4 Radio Software Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following: ? **?Navigation Failed? message is displayed. ? Navigation is inoperative or inaccurate. ? CD player will not play songs and/or locks up the radio. ? The clock will not automatically update to local time. ? The clock may be off by several hours (RA3 only). ? HVAC temperature out of sync with radio display (KL vehicles). ? Some Uconnect App remote commands do not execute with the vehicle. ? Radio Apps are inoperative. ? Radio will lock up. Radio display screen is black or blank. Battery drain due to radio staying on.** Rearview Camera image appears jittery (UF vehicles only). Inability to establish a WiFi connection when security feature is enabled (UF vehicles only). Audio distortion/popping heard while playing Apple devices through the USB port (UF vehicles only). Remote Uconnect Apps functions (i.e. door locks, remote start) inoperative while the engine is running (UF vehicles only). HVAC temperature out of sync with radio display (KL vehicles). Intermittently blind spot chime will not turn off (KL vehicles only). The radio may switch from SiriusXMT to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Audio muted after AUX device is disconnected. In addition, the following Improvements are included: **Adds Apple SiriT Eyes Free capability for iPhoneT owners. Add the ability to drag and drop icons into the menu bar. Auto Play can now be configured. Enhanced VR performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (YelpT, PandoraT, AhaT, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Park Assist Sensor 1) Active or Stored DTC of Signal Shape / Waveform Failure fault: B128E-25, B128F-25, B1290-25, B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
Source components: STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Housing Assy - Fuel Filler Door Youhave been identified aseither having stock,or have stock in transit toyour dealership. Please return allsuspect stock of part numbers:68148794AH,68148794AF,68148794AD,68156453AH,68156453AF, 68156453AD,68161542AE,68161542AD.See attachment for identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Recliner - Stow and Go: Return Youhave been identified aseither having stock,or have stock in transit toyour dealership. Please return allstock of following part numbers:68241568AB,68241568AC,68241569AB,68241569AC, 68241570AB,68241571A.Replacement part numbersare 68241568AD,68241569AD,68241570AD,68241571AD, which are in stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Park Assist Sensor 1) Active or Stored DTC of Signal Shape / Waveform Failure fault: B128E-25, B128F-25, B1290-25, B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Molding Assy ?Frt door day light opening Rt/Lt: Return You have been identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part numbers: 57010364AI, 57010365AI, 57010504AJ, 57010505AJ, 68224368AB, 68224369AB. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017.
NHTSA source summary · Original PDF not reviewed by Recallfolio
04627694AA Purge Control - Valve You have been identified as either having stock, or have stock in transit to your dealership. Suspect stock of part number: 04627694AA must be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
55395241AG Weatherseal - Windshield to Cowl Please return allstock of following part numbers:55395241AG,55395241AE.Replacement ispart number 55395241AH which isin stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 12April,2017
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 And RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 And RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).
NHTSA source summary · Original PDF not reviewed by Recallfolio
04589131AG, 04589243AG - Inspect and Return: Liftgate - Latch Assy You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 04589131AG, 04589243AG . See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 7 April, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
R4801865AC Alternator Assy - 220 Amp You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of part number R4801865AC. Replacement is part number 04801865AE which is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 04 April, 2017.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auto Trans Rotary Electronic Shifter The rotary shifter is designed to actuate a motor within the device whenever the driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacement part will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auto Trans Rotary Electronic Shifter The rotary shifter is designed to actuate a motor within the device whenever the driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacementpart will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 845RE Transmission Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience one or more of the following Symptom/Condition(s) and/or a Malfunction Indicator Lamp (MIL) due to an erroneous Diagnostic Trouble Code (DTC): P1DCD - TCM monitoring processor performance multiple clutches locked up. P1B13 - Park-By-Wire unintended out of park position. P0734 - Gear 4 Shift Incorrect Ratio set in the TCM memory.In addition, customers may experience the following conditions: Bump sensation felt during engine start/stop transition on light throttle acceleration (Stop-Start Multiple VSM System Sales Code XBU equipped vehicles only). Less than desired overall downshifts during normal driving. Less than desired downshifts during passing maneuvers. Less than desired upshift quality in lower gears.The following improvements are included in this update: Engine start/stop calibration update to allow Park and Neutral to be considered valid stop positions (Stop-Start Multiple VSM System Sales Code XBU equipped vehicles only).
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain System Improvements/EnhancementsThis bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following (DTCs) have been set:P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible (14&15 MY). P0116 - Engine Coolant Temperature Sensor Performance (14&15 MY). P0335 - Crankshaft Position Sensor Circuit (14&15 MY). U1424-00 - Implausible Engine Torque Signal Received (14&15 MY). P1239 - Engine Oil Temperature Too Low (15 MY Sales Code ERB). P0300 - Multiple Cylinder Misfire.P0456 - EVAP System Small Leak.P0607 - ECU Internal Performance.P2096 - Downstream Fuel Trim System 1 Lean.P2097 - Downstream Fuel Trim System 1 Rich. P2098 - Downstream Fuel Trim System 2 Lean. P2099 - Downstream Fuel Trim System 2 Rich. P1004 - Short Runner Valve Control Performance. P2008 - Short Runner Valve (SRV) Control Circuit. P2016 - Intake Manifold Runner Position Sensor Circuit Low. P2017 - Intake Manifold Runner Position Sensor Circuit High. P26AB - Engine Coolant Bypass Valve Stuck.U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful) (with 4.7L or 3.6L).P0607 - ECU Internal Performance. (with 4.7L).The following improvements are included in this update:Throttle Position Sensor (TPS) calibration (14&15 MY).Corrects a false oil pressure lamp illumination at key on (14&15 MY with 5.7L).Shift quality of the first shift after a few hours of vehicle drivetrain cooling down.Automatic Shut Down (ASD) Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown).Charging system voltage regulator control improvements.System improvements to prevent MIL illumination with a DTC P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures grea
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Dealers are replacing water pumps because of a coolant leak. Water pumps are found TNF but the water pump bypass o-ring was pinched resulting in a coolant leak that looks like a failed pump. Please inspect the bypass o-ring before replacing the pump as it is available separate for service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TANK, Diesel Exhaust Fluid, Part Includes Temp Sensor and Level Sensor For DS and WK vehicles ONLY; If the urea tank is being replaced due to P249C, P203E, or P24F3 on a 2014-2016 model year 3.0L Turbo Diesel (EXF) on DS or WK, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. The purpose of this software release is to enable the capability to capture non Diagnostic Trouble Code (DTC) control module data through the Uconnect Data Recording system. Improved shift scheduling to expand the operating range of 8th gear. Improved 7th gear upshift timing.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USB Charging Port Before replacing this part - this is a charge only USB port intended to charge smart phones and other low power USB devices. To verify proper functionality, turn on the ignition with no cables or devices plugged into the port. Connect a charging cable to the port, then connect the device. If the device receives power, the port is functioning to design. There are some minor compatibility issues with some charging cables including Apple Lightning cables. For questions regarding the charging port functionality, please call Dave Diovardi at Cell (248) 941-8704 or Rick Gordon at Cell (248) 630-6281.~
Source components: ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS:ACCESORY POWER OUTLET/JACK/PORT/USB/SAE/CIGARETTE LIGHTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Thermal Expansion Valve (TXV), H-valve For D trucks only; When diagnosing an A/C system leak at the TXV (Thermal Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA, 68046015AA, 68100682AA, 68100676AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair.~ ~___________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.
Source components: ENGINE AND ENGINE COOLING · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.