The manufacturer’s record · Page 4 of 4
Original record summaries, dates and identifiers for this model-year. Records 301–332 of 332, ordered newest first. Dated records on this page: Sep 26, 2013–Jul 30, 2014.
Back to 2014 Nissan ROGUE problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10056134
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: USE CORRECTED SPECIFICATION (SD) FOR POSITIONING TARGETS WHEN PERFORMING THE CALIBRATION FOR REAR VIEW CAMERA, THAT MONITORS TRAVELING LANE. MODEL 2014 ROGUE.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10056134 at NHTSANHTSA communication ID: 10192406
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The maintenance interval mileage in the Vehicle Information Display resets to zero with each ON > OFF > ON ignition cycle, ACTION Reprogram the Vehicle Information Display (METER/M&A) per the Service Procedure in this bulletin. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10192406 at NHTSANHTSA communication ID: 10192402
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ---- Page 2 - Two (2) Intelligent Keys Are Lost ---- Page 3 NOTE - If both Intelligent Keys are lost with the BCM in Transit Mode, the BCM and ECM will need to be replaced. Refer to pages 3 - 5 for more information. See this bulletin for more detail.
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE.
Source record 10192402 at NHTSANHTSA communication ID: 10192397
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a dealer inventory inspection of the automatic climate control system operation on 910 specific 2014 Rogue vehicles identified in SERVICE COMM.
Source components: EQUIPMENT · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10192397 at NHTSANHTSA communication ID: 10192394
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10192394 at NHTSANHTSA communication ID: 10192393
NHTSA source summary · Original PDF not reviewed by Recallfolio
The original VIN list provided with the initial announcement contained 29 vehicles that are not equipped with push-button ignition. These 29 vehicles are exempt from the repair and are no longer subject to the quality hold.
Source components: ELECTRICAL SYSTEM:IGNITION · EQUIPMENT.
Source record 10192393 at NHTSANHTSA communication ID: 10192391
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a dealer inventory service action to replace the push button ignition switch on 158 specific 2014 Rogue vehicles identified in SERVICE COMM.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
Source record 10192391 at NHTSANHTSA communication ID: 10192390
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION For 2014 - 2015 Rogue (T32) equipped with third row seats: Do not install or add a spare tire to the vehicle. The vehicle is not designed to be equipped with a spare tire. See this bulletin for further detail.
Source components: EQUIPMENT · TIRES.
Source record 10192390 at NHTSANHTSA communication ID: 10192380
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When performing Distance Sensor Alignment, use the corrected specification (L) for positioning the target board. NOTE: The Distance Sensor is used for the Forward Collision Warning (FCW) system. The specification in the ElectronicService Manual (ESM), Section DAS, Driver Assistance Systems, for positioning the Distance Sensor Target Board is incorrect. Use the corrected specification (L) listed in this bulletin.
Source components: EQUIPMENT · FORWARD COLLISION AVOIDANCE.
Source record 10192380 at NHTSANHTSA communication ID: 10055919
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: THE POSITIONING OF DISTANCE SENSOR TARGET BOARD IS INCORRECT, IN ELECTRONIC SERVICE MANUAL (ESM), AND THE CORRECTED SPECIFICATION (L), IS USED TO PERFORM THE DISTANCE SENSOR ALIGNMENT. MODEL 2014 ROGUE. *PE
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10055919 at NHTSANHTSA communication ID: 10192374
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Factory wheel covers are installed on vehicles during Pre Delivery Inspection (PDI). Care must be taken to properly install the wheel covers to avoid damage. Go to SERVICE PROCEDURE in this bulletin for proper wheel cover installation. NOTE: Damage to wheel covers caused by improper installation is not covered under warranty. See this bulletin for further detail.
Source components: EQUIPMENT · WHEELS.
Source record 10192374 at NHTSANHTSA communication ID: 10192373
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The "front door power window and door lock/unlock switch (RH) finisher" (switch finisher) has a loose fit, causting an excessive gap. See Figure 1. ACTION: 1. Remove the passenger front door finisher (door finisher). - Refer to the Electronic Service Manual (ESM), section INT-Interior, for removal procedure. 2. Install a foam block where shown in SERVICE PROCEDURE. - Use the foam block listed in PARTS INFORMATION. 3. Install the door finisher with a new switch finisher listed in PARTS INFORMATION. - Refer to the ESM, section INT-Interior, for installation procedure. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · STRUCTURE.
Source record 10192373 at NHTSANHTSA communication ID: 10192361
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10192361 at NHTSANHTSA communication ID: 10192354
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM:WIRING.
Source record 10192354 at NHTSANHTSA communication ID: 10192348
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: An electrical issue caused by corrosion in the Main Harness to Body Harness connectors located at the bottom of the driver side A-pillar: Connector numbers M13 to B3 and/or M14 to B4. ACTIONS: 1. Preform repairs to harness connectors as needed. 2. Apply Harness Protector to cover the harness connectors. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM.
Source record 10192348 at NHTSANHTSA communication ID: 10055490
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: THE MAIN HARNESS TO BODY HARNESS CONNECTORS IS EXPERIENCING ELECTRICAL CORROSION ISSUES. 2008-2014 ROGUE. *PE
Source components: ELECTRICAL SYSTEM.
Source record 10055490 at NHTSANHTSA communication ID: 10192344
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The Instrument Lower Panel LH (as shown in Figure 1) molded plastic clip will not stay secured. ACTION Install a shim between the Steering Member and the Instrument Panel and apply felt tape to the Instrument Lower Panel LH with the SERVICE PROCEDURE starting on page 2. Please see this bulletin for further details.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · STEERING.
Source record 10192344 at NHTSANHTSA communication ID: 10192341
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a Dealer Inventory Inspection to inspect the right front and right rear lug nuts on 372 certain specific 2014 Nissan Rogue and Pathfinder vehicles currently in dealer inventory.
Source components: EQUIPMENT · WHEELS.
Source record 10192341 at NHTSANHTSA communication ID: 10192339
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10192339 at NHTSANHTSA communication ID: 10192337
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10192337 at NHTSANHTSA communication ID: 10192336
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The MIL is on with any one of these DTCs alone, or any combination of any of DTCs: * P2765 - CLUTCH B SPEED SENSOR * P0500 - VEH SPEED SEN/CIRC * P1574 - ASCD VHL SPD SEN * P1715 - INPUT SPEED SENSOR * P0720 - VEH SPD SEN/CIR And * Moisture and/or corrosion is present on or around the Secondary Speed Sensor pins. ACTION a. Remove the moisture from the Harness connector with CRC QD (or equivalent) electric cleaner. b. Replace Secondary Speed Sensor shown in Figure 1. Please see this bulletin for further details.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10192336 at NHTSANHTSA communication ID: 10192335
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10192335 at NHTSANHTSA communication ID: 10192330
NHTSA source summary · Original PDF not reviewed by Recallfolio
On a very small percentage of vehicles, the steering column bolt may need to be replaced by the dealership. Nissan is placing the vehicles that have not had the inspection performed on a Quality Hold.
Source components: EQUIPMENT · STEERING.
Source record 10192330 at NHTSANHTSA communication ID: 10192329
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a Dealer Service Action to inspect and, if necessary, replace the steering knuckle on certain specific 2014 Nissan Rogue vehicles currently in inventory.
Source components: EQUIPMENT · STEERING.
Source record 10192329 at NHTSANHTSA communication ID: 10192327
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a Dealer Service Action to inspect the steering column bolt on certain specific 2014 Nissan Leaf and Rogue vehicles currently in dealer inventory only.
Source components: STEERING.
Source record 10192327 at NHTSANHTSA communication ID: 10192305
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
Source components: AIR BAGS · EQUIPMENT.
Source record 10192305 at NHTSANHTSA communication ID: 10192295
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a Dealer Service Action to inspect the CVT output speed sensor on certain specific 2014 Nissan Altima, Pathfinder, Rogue vehicles currently in dealer inventory only.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10192295 at NHTSANHTSA communication ID: 10192293
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
Source components: ENGINE · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
Source record 10192293 at NHTSANHTSA communication ID: 10192282
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Intelligent Key (I-Key) systems on the Applied Vehicles use two (2) different Radio Frequencies (RF) that are similar to other wireless devices; 315 MHz and 433 MHz. In the event another wireless device (e.g. aftermarket alarm system) is transmitting at the same time as an I-Key, it can interfere with the I-Key signals being received by the BCM. If there is interference with I-Key signals, the following symptoms may occur: - The I-key is not detected, causing: - The engine to not start (no response when the Stop/Start button is pressed) - "I-Key System Error" displayed in the instrument cluster - "No I-Key Detected" displayed in the instrument cluster - Intermittent operation of the buttons on the remote (Key FOB). - Intermittent operation of the door request switches. If a vehicle has experienced the above symptoms, or a customer has reported the above symptoms, refer to Supplemental Diagnosis / Information in this bulletin. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
Source record 10192282 at NHTSANHTSA communication ID: 10192273
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a Dealer Service Action to inspect for water leaks at the rear liftgate glass on certain specific 2014 Nissan Rogue vehicles currently in dealer inventory.
Source components: EQUIPMENT · STRUCTURE.
Source record 10192273 at NHTSANHTSA communication ID: 10192267
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a Dealer Service Action to inspect, remove, clean and, reinstall the shifter knob assembly on certain specific 2014 Nissan Rogue vehicles currently in dealer inventory.
Source components: EQUIPMENT · POWER TRAIN.
Source record 10192267 at NHTSANHTSA communication ID: 10054527
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: INFORMATION REGARDING TIRE PRESSURE MONITOR SYSTEM (TPMS) AND LOW TIRE PRESSURE WARNING SYSTEM (LTPWS) FOR SENSOR LEAKS, AIR PRESSURE CHANGES WITH ALTITUDE AND AMBIENT TEMPERATURES, AFTERMARKET WHEELS, RADIO FREQUENCY INTERFERENCE CAUSING NO DATA CONDITION AND INFLATING/DEFLATING TIRES WITH TPMS/LTPWS SENSORS. MODEL ALL. NO MODELS YEARS. *PE
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
Source record 10054527 at NHTSA