Original record summaries, dates and identifiers for this model-year. Records 401–500 of 512, ordered newest first. Dated records on this page: Feb 8, 2017–Mar 26, 2018.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 26, 2018Service Bulletin/Repair Instructions
02-006-18-3449
NHTSA communication ID: 10134930
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear incertain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The SKYACTIV®-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV® oil filters. The unique oil filter can be identified with two white bands as shown below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.504 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On some vehicles, the second-row seat back does not fold (B) or slide (C) forward when the walk-in lever (A) is pulled up to access to the 3rd row seats. Also, the recliner lever knob (D) may not operate on some vehicles. These concerns may be caused by a disconnected walk-in lever cable. To eliminate these concerns, the design of the walk-in lever has been changed according to the following.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during extremely cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during extremely cold temperatures. To correct the concern, the SD card hardware has been changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about the MAZDA CONNECT center display cracking (spider cracking). The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The navigation SD Card VIN-locks to a vehicle in the following conditions: 1. Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Navigation SD Card Map Update Note: Mazda Toolbox navigation SD card map update can only be performed on a navigation SD card that is VIN-locked. See VIN-lock procecure below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain CX-9 vehicles may experience a creaking/squeaking noise from the right rear suspension. The noise may occur while traveling at lower speeds or coming to a stop, or when starting from a stop. The noise can also be duplicated by gently bouncing the right rear suspension (i.e. simulating the movement of a passenger exiting the right rear door). The creaking noise may be caused by stick-slip between the upper spring seat rubber and the coil spring.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a lack of power with no warning lights illuminated and no related DTCs stored. This concern most likely occurs when the fuel temperature is high and during situations where high power is required. This concern may be caused when the learning value for the low pressure fuel pump exceeds a certain level and the PCM limits engine power to avoid a lack of fuel injection. Even if the low pressure fuel pump has a problem, no DTCs are stored. To eliminate this concern, the PCM control logic has been modified not to limit engine power. After this modification, DTCs P0192:00 or P0087:00 are stored when the fuel injection amount is insufficient. P0192:00 - High fuel pressure sensor circuit low input P0087:00 - High fuel pressure sensor circuit range/performance problem.
Source components: ENGINE · FUEL SYSTEM, GASOLINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth® and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge, Blank Screen and/or No Audio Sound
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the door weatherstrip (1) comes off at the front / lower part of the reardoor(s). This concern is caused by insufficient weatherstrip gripping force.
NHTSA source summary · Original PDF not reviewed by Recallfolio
After parking the vehicle at temperatures below the freezing, some customers may experience a lack of power with the check engine light on and DTC P0638:00 and/or P2112:00 stored in memory. - P0638:00: Throttle valve actuator control range/performance problem (one drive cycle DTC) - P2112:00: Throttle valve actuator motor currentrange/performance problem (one drive cycle DTC) This concern may be caused by condensed water in the intake manifold entering the throttle valve. After parking at temperatures below freezing, the throttle valve may be frozen at the stand-by position, resulting in the symptom. To prevent this concern, the control logic of the PCM has been modified to avoid frozen the throttle valve (by moving the valve at a certain time after the ignition has been turned off). NOTE: With this modification, the main relay may stay on up to 90 minutes after the ignition switch is turned off. "BATTERY INSPECTION" in the Workshop Manual will be modified to properly check the battery parasitic draw after this modification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the door weatherstrip (1) comes off at the front / lower part of the reardoor(s). This concern is caused by insufficient weatherstrip gripping force.
NHTSA source summary · Original PDF not reviewed by Recallfolio
After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle.Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.CX-3 shown:Vehicles having this concern should have their vehicle repaired using the following procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during coldtemperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD card hardware has been changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a lack of power when driving. The master warning light or the check engine light turns on and DTC P130C:00 and U0401:00 (ABS) stored in memory. It occurs mostly at low temperatures. Once the ignition is turned off and on, the concern may disappear. NOTE: DTC P130C:00 may not be found upon M-MDS self test since this DTC is detected when the condition occurs in two drive cycles in a row. The PCM turns the master warning light on during the first drive cycle, then stores a pending DTC. The master warning light and check engine light come on in the second drive cycle as a confirmation of the DTC. The engine power is limited by the fail-safe function both in the first and second drive cycles. DTC P130C:00 - (Pre-ignition detected), DTC U0401:00- (ABS) (Signal error from PCM) Improper control logic of the PCM detects a normal operating noise as a knocking noise. To eliminate this concern, the control logic of the PCM has been changed.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If the BSM control module is replaced, Auto Configuration and BSM Radar Test must be performed: 1. Auto Configuration -When the ignition is switched ON, the blind spot monitoring (BSM) reads the vehicle specification information sent via CAN communication from the instrument cluster, and stores the vehicle specification information into the new BSM control module. 2. BSM Radar Test - This test confirms correct BSM module/bracket alignment. The Workshop Manual "BLIND SPOT MONITORING (BSM) RADAR TEST" is incorrect. Mazda is in the process of correcting the error. Perform the following procedure temporarily until the Workshop Manual is corrected:
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit one or more of the following noises from the front suspension: 1. A creaking noise from under the front of the vehicle (front lower arm bushing) when driving over bumps atapproximate 12 - 25 mph (20 - 40 Km/h). The noise occurs when the road surface is wet or after the vehicle has been washed. The noise becomes more noticeable as the bumps get higher. The creaking noise is caused by the front lower arm bushing (A) making a stick-slip noise during wet road conditions. 2. A clunking noise from the front coil spring when driving over bumps. The clunking noise is due to stick-slip between the front strut bearing (B) and the coil spring (C). 3. A popping noise from the bump stopper (D) when driving through gutters. To eliminate the noise, the following mass-production changes have been made: 1. The coating treatment of the lower arm bushing has been changed to reduce friction and prevent stick-slip. 2. Protectors have been installed onto the coil springs to prevent stick-slip. 3. No mass-production change is scheduled for the bump stopper, however, a modified service part has been established.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address these customer concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The MODE switch operation for the Mazda Radar Cruise Control (MRCC) system has been changed as follows: Previous - Press the MODE switch to switch to the cruise control function. New - Press the MODE switch and hold for 2 seconds_ to switch to the cruise control function.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot perform any additional testing of the system. Dealers and customers should never attempt to test or recreate crash scenarios under any circumstances because that could lead to an accident and injuries. NOTE: This article only applies to the applicable vehicles below equipped with SCBS system that uses a Laser Sensor. This article does not apply to newer vehicles equipped with SCBS system that uses a Forward Sensing Camera (FSC).
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you receive a customer complaint of an engine oil warning light illuminating, with DTC P250A:00 stored in the PCM, it may be caused by overfilling the engine oil.
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: ? Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area.? Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address these customer concerns.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with a vehicle ahead is imminent. In addition, the system reduces damage in the event of a collision by operating the brake control when the system determines that a collision is unavoidable. It may also be possible to avoid a collision depending on the relative speed between your vehicle and the vehicle in front of you. In addition, when the driver depresses the brake pedal, the brakes are applied firmly and quickly to assist.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.
Source components: ELECTRICAL SYSTEM · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit one or more of the following noises from the front suspension: 1. A creaking noise from under the front of the vehicle (front lower arm bushing) when driving over bumps at approximate 12 - 25 mph (20 - 40 Km/h). The noise occurs when the road surface is wet or after the vehicle has been washed. The noise becomes more noticeable as the bumps get higher. The creaking noise is caused by the front lower arm bushing (A) making a stick-slip noise during wet road conditions. 2. A clunking noise from the front coil spring when driving over bumps. The clunking noise is due to stick-slip between the front strut bearing (B) and the coil spring (C). 3. A popping noise from the bump stopper (D) when driving through gutters.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience a knocking noise from the front and/or rear shock absorbers when driving over rough roads or speed bumps. The noise may be caused by damage to the inner seal of shock absorber, resulting in fluid seepage. To eliminate this concern, modified parts with improved oil sealing performance have been established as service parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On some vehicles, the second-row seat back does not fold (B) or slide (C) forward when the walk-in lever (A) is pulled up to access to the 3rd row seats. Also, the recliner lever knob (D) may not operate on some vehicles. These concerns may be caused by a disconnected walk-in lever cable. To eliminate these concerns, the design of the walk-in lever has been changed according to the following:
NHTSA source summary · Original PDF not reviewed by Recallfolio
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:HEADLIGHTS · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the 8-inch center display sometimes turns black while driving. When the display turns black, the sound (for navigation or audio system) can still be heard and the volume can be controlled. The center display may return to normal after turning the ignition switch off, then on again. This concern may be caused by internal noise within the center display, which disturbs the integrated DC-DC converter and results in no power for the display. To eliminate this concern, the hardware for the center display has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On some vehicles, the front bumper cover may pop out causing a poor appearance complaint. This may be caused by an insufficient amount of holding force of the bumper slider. To eliminate this concern, the configuration of the bumper slider has been changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience DTC P064A stored in the PCM memory. There is no drivability concern and a technician may find this DTC during diagnosis for another concern. P064A:00 - (Fuel Pump Control Module Error). [Detection Condition] The difference between the actual fuel pressure and the target fuel pressure is 10 kPa {0.10 kgf/cm2, 1.5 psi} or more, even though the fuel pressure feedback amount on the low pressure side remains high. [Diagnosis Support Note] ? This is a continuous monitor (other). ? The check engine light does not illuminate. ? FREEZE FRAME DATA is not available. ? Snapshot data is available. ? DTC is stored in the PCM memory. The DTC may be set by an inadequate detection logic. To eliminate this concern, the detection function of DTC P064A has been disabled.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a lack of power when driving. The master warning light or the check engine light turns on and DTC P130C stored in memory. It occurs mostly at low temperatures. Once the ignition is turned off and on, the concern may disappear. The PCM turns the master warning light on during the first drive cycle, then stores a pending DTC. The master warning light and check engine light come on in the second drive cycle as a confirmation of the DTC. The engine power is limited by the fail-safe function both in the first and second drive cycles. DTC P130C:00 - (Pre-ignition detected). Improper control logic of the PCM detects a normal operating noise as a knocking noise. To eliminate this concern, the control logic of the PCM has been changed.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There is a minor error with the Controller Programming instructions included with the accessory remote start kit C960-V7-620. In the current "Registration (programming) of the controller" instructions, step 5 shows an incorrect image. The function button is the lower button. A revised set of instructions are available in the Accessory E catalog and will be included in all kits at the next revision point.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAUTION: DO NOT attempt any repair of the windshield damaged by stone chipping/cracks at the area in front of the Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that 1) the air conditioner is not cold enough or 2) the cabin is cold, but the fan speed stays on high and there is noise coming from the blower motor or 3) it is difficult to adjust the driver/passenger side ventilation grill so that the air flows directing to the driver?s/passenger?s face.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the third-row seat headrest(s) are loose (A) and do not lock in the upright position (B) or the headrest are locked in the forward-bent position (C). These concerns are caused by improper operation while the seatback is folded down (A) and an excessive force is applied to the headrest (B) while it's in the upright locked position. When excessive force is improperly applied, this causes damage to the headrest lock mechanism (C).
NHTSA source summary · Original PDF not reviewed by Recallfolio
On some vehicles, the front bumper cover may pop out causing a poor appearance complaint. This may be caused by an insufficient amount of holding force of the bumper slider.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There are a few issues with the accessory C960-V7-620 remote start kit instructions. In the current ?Registration (programming) of the controller? instructions, step 5shows an incorrect image. The function button is the lower button. The correct set of instructions are below. The instructions for registration of additional remotes is not available on the E-catalog web site at this time. The instructions are below. A troubleshooting guide is not available on the E-catalogs web site at this time. The instructions are below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit one or both of the following noises from the front suspension: 1. A creaking noise from under the front of the vehicle (front lower arm bushing) when driving over bumps at approximate 12 - 25 mph (20 - 40 Km/h). The noise occurs when the road surface is wet or after the vehicle has been washed. The noise becomes more noticeable as the bumps get higher. The creaking noise is caused by the front lower arm bushing (A) making a stick-slip noise during wet road conditions. 2. A clunking noise from the front coil spring when driving over bumps. The clunking noise is due to stick-slip between the front strut bearing (B) and the coil spring (C).To eliminate the noise, the following mass-production changes have been made: 1. The coating treatment of the lower arm bushing has been changed to reduce friction and prevent stick-slip. 2. Protectors have been installed onto the coil springs to prevent stick-slip.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tabin MAZDA CONNECT Settingsbefore performing the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a lack of engine power / intake air leak noise from the engine compartment. Hose clamps A and/or B for the air hose (C) for the turbocharger air outlet pipe (D) may be loose due to insufficient tightening. The tightening torque of the hose clamps has been increased to eliminate this concern.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom. If the condition is similar to the following "CONTROL LOGIC OF AMBIENT TEMPERATURE" or "DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS", advise the customer that this is a normal characteristic of the vehicle and not a malfunction. If the condition does not meet the following and the sensor malfunction is suspected, make sure to inspect the sensor according to MGSSonline or Workshop Manual (section 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). Replace the sensor only when it fails the Workshop Manual inspection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Audio, navigation and phone concerns with Mazda connect Infotainment system. All Mazda connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later). NOTE: For CX-9 with version earlier than 59.00.441, the tachometer function has been removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
An update to the MAZDA CONNECT system is now available for download from the Mazda Global Service Support (MGSS) system. The new version number is 59.00.502. Please refer to TSB 09-017/17 for a list of improvements to the system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that 1) the air conditioner is not cold enough or that 2) the cabin is cold, but the fan speed stays on high and there is noise coming from the blower motor. The following may be the causes: 1)The A/C compressor ON/OFF control is not operating correctly, causing a problem with the air temperature control. 1)The air conditioner may not be cool enough due to inadequate amount of the refrigerant, due to leakage or overcharging. 2)The control of the amount of air blown is incorrect. To eliminate these concerns, the front and rear climate control unit software has been modified to optimize the amount of air blown and the A/C compressor ON/OFF controls.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Poor air conditioning performance and operation. Some customers may complain that 1) the air conditioner is not cold enough or that 2) the cabin is cold, but the fan speed stays on high and there is noise coming from the blower motor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that 1) the air conditioner is not cold enough or that 2) the cabin is cold, but the fan speed stays on high and there is noise coming from the blower motor. The following may be the causes: 1)The A/C compressor ON/OFF control is not operating correctly, causing a problem with the air temperature control. 1)The air conditioner may not be cool enough due to inadequate amount of the refrigerant, due to leakage or overcharging. 2)The control of the amount of air blown is incorrect. To eliminate these concerns, the front and rear climate control unit software has been modified to optimize the amount of air blown and the A/C compressor ON/OFF controls.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EQUIPPED WITH MAZDA RADAR CRUISE CONTROL (MRCC) WILL NOT SET (THE SYSTEM STAYS ON STANDBY) IF THE DRIVER'S SEAT BELT IS NOT FASTENED. THIS IS A NORMAL CONDITION. DO NOT PERFORM ANY REPAIRS FOR THIS CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PERMANENT DTCS ARE NOW DISPLAYED WITH THE IDS 104 UPDATE. THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. ALL PCM AND TCM DTCS THAT TURN ON THE CHECK ENGINE LIGHT CAN REMAIN AS A PERMANENT DTC. THEY WILL NOT TURN ON THE CHECK ENGINE LIGHT OR CAUSE DRIVABILITY CONCERNS. IF YOU ENCOUNTER A PERMANENT DTC, IGNORE IT AND DIAGNOSE THE CURRENT STORED OR PENDING DTC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING ADVANCED KEYLESS ENTRY SYSTEM MALFUNCTIONS: (1) KEY FOB AND/OR DOOR REQUEST SWITCH DOES NOT OPERATE. (2) DOOR LOCKS REPEATEDLY LOCK AND UNLOCK WHEN APPROACHING THE VEHICLE WITH THE ADVANCED KEY. (3) KEY WARNING LIGHT (RED) ON WHILE DRIVING AND DTC B10D1:23 AND/OR B10D3:23 IS(ARE) STORED. B10D1:23 REQUEST SWITCH (LF) CIRCUIT MALFUNCTION B10D3:23 REQUEST SWITCH (RF) CIRCUIT MALFUNCTION
NHTSA source summary · Original PDF not reviewed by Recallfolio
Take caution when cleaning plastic headlight lenses. Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Damage caused by using these cleaners is not covered by Mazda's New Vehicle Limited Warranty term.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lift gate hinge nut concern - On effected vehicles, the tightening torque of lift gate hinge nuts at cabin side does not meet the specified value. Due to this, it may cause interference/noise with the body when closing/opening the lift gate, or water leakage may occur inside cabin. Originally the coincerned nuts are tightened to the specified torque at the production line. However, the thickness of the packing between the lift gate hinge and body shrinks slightly by heat during paint baking process, resulting in a lowered tightening torque.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HVAC Humidity Sensor change. A new type of HVAC humidity sensor has been added to some models with sport Trim. This new sensor is mounted on the inside of the windshield near the rear view mirror.