Original record summaries, dates and identifiers for this model-year. Records 1–100 of 512, ordered newest first. Dated records on this page: Feb 16, 2023–Jun 19, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 19, 2026Service Bulletin/Repair Instructions
SA-041-26
NHTSA communication ID: 11034447
NHTSA source summary · Original PDF not reviewed by Recallfolio
This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 01-008/23 06/05/23 Some vehicles may exhibit rattling noises from the engine compartment and oil leakage from the drive belt auto tensioner. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed. REPAIR PROCEDURE If the tensioner is found to be "No Good" after completing the Drive Belt Auto Tensioner Inspection, replace it with a modified part according to the instructions on MGSS online:
NHTSA source summary · Original PDF not reviewed by Recallfolio
DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
Source components: ENGINE · POWER TRAIN · SERVICE BRAKES · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit codes. • Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. • For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When inspected, the differential or PTO oil is dark or black. This is considered normal and NO repair should be performed. During production, differential ring and pinion gears receive a manganese phosphate coating (commonly referred to as black oxide). This coating forms a porous, oil-retentive surface that improves boundary lubrication and reduces adhesive wear during initial contact cycles. Designed as a sacrificial layer, it is gradually removed under load throughout the break-in process. As a result, after the first few hundred miles, or at the initial gear oil service interval, the lubricant may appear darkened by the worn-off coating. It will contain trace ferrous particles from the normal run-in of the gear teeth and bearing surfaces. This condition is expected and does not, by itself, indicate an issue with the differential or PTO gears.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Noise, Vibration, and Harshness (NVH) Diagnostic Guidelines Diagnostic Guidelines When diagnosing NVH concerns, it is essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.
Source components: POWER TRAIN · STEERING · SUSPENSION · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the MAZDA CONNECT tuner and amp unit (TAU) with a replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Customer Service Program (CSP11) to extend the limited powertrain warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a noisy HVAC blower motor or odor after a cabin air filter replacement. Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit following symptoms: 1. The rearview mirror (1) rattles up and down (2) while adjusting the mirror. 2. The rearview mirror (1) makes a rattle noise depending on the road surface conditions while driving. This concern is caused during rearview mirror installation. The adhesive is squeezed out between the windshield and the mirror base. The rearview mirror is assembled on top of the overextended adhesive. The adhesive is softened by heat, and loosening screws, results in a rattling concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Dear Mazda Owner: You are receiving this notice because Mazda’s records indicate that your 2019-2020 CX-5, 2016-2020 CX-9, or 2018-2020 Mazda6 vehicle was equipped with a SKYACTIV-G 2.5T (Turbocharged) engine (“Covered Vehicle”). Mazda Motor Corporation has decided to conduct a Customer Service Program CSP (11) to inform you that Mazda is extending the limited powertrain warranty to provide necessary repairs free of charge if your Covered Vehicle has coolant leaks at the cylinder head around the exhaust manifold and to inform you that you may be eligible to receive reimbursement for past out-of-pocket expenses you previously incurred for such repairs on the terms and conditions as described below. Powertrain Warranty Extension: Mazda is extending the limited powertrain warranty to 10 years or 120,000-miles, whichever occurs first, to provide necessary repairs at no cost to you if your Covered Vehicle has coolant leaks at the cylinder head around the exhaust manifold. A dealer must inspect and confirm your Covered Vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for you to receive the repairs at no cost to you.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CSP11 - COOLANT LEAKS AT CYLINDER HEAD WARRANTY EXTENSION For certain 2019-2020MY CX-5, 2016-2020MY CX-9, 2018-2020MY Mazda6 that are equipped with SKYACTIV-G 2.5T engine, the warranty coverage for specific repair of the coolant leak at cylinder head is extended to: 10 years (120 months) or 120,000 miles (192,000 km) whichever comes first, from the original warranty start date CONDITION OF CONCERN On certain subject vehicles, the coolant may leak at the cylinder head around the exhaust manifold.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The SKYACTIV-DRIVE FW6A-EL AT uses “Automatic Transmission Fluid (ATF) Type: FZ”. Only use “ATF-FZ” to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Customer Service Program (CSP11) to extend the limited powertrain warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Customer Service Program (CSP11) to extend the limited powertrain warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Customer Service Program (CSP11) to extend the limited powertrain warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Please review the entire Dealer Email below announced on October 17, 2024 for full details regarding this campaign. Warranty Information is at the bottom of the TSB Parts and Warranty information and Repair Procedures will be available by October 25, 2024. Until that time if a vehicle is presented to your dealer with a complaint and CSP11 is visible in eMDCS, please click here and follow instructions in TSB 01-002/23 COOLANT LEAKS AT CYLINDER HEAD and hold claims until the Parts and Warranty Information is available in eMDCS and MGSS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10 °C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the rear console / cup holder area is warming. The warming is caused by heat radiating from the rear heater core, which is located under the console. The warm air created by the heater core escapes through small
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10 °C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · SERVICE BRAKES, HYDRAULIC · STEERING · TIRES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a creaking or clacking noise when operating the power lift gate (PLG). The noise may be caused by the following: Creaking noise: Dust and dirt accumulates on the sealing portion of the PLG drive unit, reducing sealing performance. Snow and water may enter the PLG drive unit. Humidity then causes rust inside of the unit, resulting in noise. Clacking noise: Since the grease applied on the spring end of the PLG drive unit is insufficient, interference noise is caused when the spring end interferes with the spring guide. The noise has been eliminated by the following mass-production changes: Creaking noise: The sealing structure has been modified to prevent dust/dirt from entering the unit. Clacking noise: The production procedure of the PLG drive unit has been modified to apply sufficient grease to spring end.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a creaking, knocking, rattle or clunk noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience electrical devices that cannot be charged through the rear console or the trunk side trim USB power outlet. This may be caused by an excessive external force applied to the USB power outlet. To eliminate this concern, the soldering strength of the USB port has been enhanced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience electrical devices that cannot be charged through the rear console or the trunk side trim USB power outlet. This may be caused by an excessive external force applied to the USB power outlet. To eliminate this concern, the soldering strength of the USB port has been enhanced.