2016 GMC SIERRA 1500 Manufacturer communications & TSBs.Page 8
Original record summaries, dates and identifiers for this model-year. Records 701–800 of 1,212, ordered newest first. Dated records on this page: Nov 7, 2017–Jun 12, 2018.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 12, 2018Service Bulletin/Repair Instructions
PIP5498K
NHTSA communication ID: 10143438
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates. A vehicle may have a concern ofDTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers foot well area when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.
Source components: AIR BAGS · EQUIPMENT:ELECTRICAL · POWER TRAIN · STEERING · SUSPENSION · TRACTION CONTROL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates information to have dealers contact TCSC for programming assistance with new amplifier part numbers until all the new amplifier numbers are setup correctly for programming.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: ELECTRICAL SYSTEM · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the Generator Control Module (GCM). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage Battery Interface Control Module 1 and 2, Drive Motor Generator Battery Cooling Blower. The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for theGenerator Control Module (GCM). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (L83), 5.3L (L86), 6.2L (LV3) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: BACK OVER PREVENTION: WARNINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle’s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Both Front Low Beam, High Beam, Day Time Running Lamps (DRL) and Turn Signals Inoperative.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.
Source components: ELECTRICAL SYSTEM · SUSPENSION:FRONT:SHOCK ABSORBER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesP0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the A15, Starter Generator (MGU). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that water leaking into the headlamp assembly or headlamp assembly connections can cause an electrical short which will keep modules from shutting down causing a dead battery and a no crank condition, a crank no start,or unable to program the engine control module. Engine control module will set a diagnostic trouble code of P1682, or the engine will continue to run with the ignition off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show “No Audio” in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.
Source components: AIR BAGS · ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY · LANE DEPARTURE · POWER TRAIN · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION · SEAT BELTS · SERVICE BRAKES, HYDRAULIC · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have either the truck or the snowplow's headlights are flickering or inoperative. There may be a diagnostic trouble code B2575 and or a B2699 set in the body control module. Technician will need to contact the snowplow manufacturer for additional information on their headlight changeover system. Technician is to refer to the latest version of the General Motors up-fitter integration bulletin 116 for additional information these circuits. Technician can find this information at http://www.gmupfitter.com/, under the "Technical Bulletin" Tab and then "Show all bulletins."
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: BACK OVER PREVENTION · FUEL SYSTEM, GASOLINE · POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon Malfunction Indicator Lamp on. Technician should follow published Service Information diagnostics that will lead to an oil pump replacement. Technician should replace the oil pump. If debris is found, the main and rod bearings should be inspected before engine replacement is considered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.
Source components: COMMUNICATION · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · COMMUNICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
Source components: STRUCTURE:BODY:HOOD · STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Trailer connection not recognized or “Check Trailer wiring” or “Service Trailer Brake” message. Technician may find Diagnostic Trouble Codes C1112, C1113, C1114, C111B, U1556, and/or U1505. Technician will need to inspect the battery and Trailer Brake Power Module connector for corroded terminals and replace as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have installed an aftermarket bed cap or topper may question where they can wire in the center high mounted stop light for the cap or topper. Provisions for the center high mounted stop light have been provided at the Rear Body Junction Block (X63A) connector X6 terminal 1 for 2014-2015 model years. For vehicle model years 2016-2017 provisions for the center high mounted stop light have been provided at connector X400 terminal 4, circuit 1054.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Malfunction Indicator Lamp Illuminated with DTCs P0335, P0340, or P0365 Set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about owners that want the auto door lock disabled. There is no avalible setting or Body Control Module calibration to turn off the auto door locks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Upfitters questions about installing aftermarket electrical accessories. Dealer should reference the latest version of General Motors Upfitter Integration Bulletin 115 for this information. It can be found at http://www.gmupfitter.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that vehicles with front seat Regular Production Option Codes A52, AZ3, or B3F may comment about low treble, or excessive bass from the front door speakers. This is a normal design characteristic for this seat configuration. These vehicles lack a subwoofer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, possible battery drain concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection dropped, the radio station or volume changes when operating the snow plow. Please advise the customer that engineering is aware of this concern and working on this issue.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a false setting of DTCU0121 in the FVCM due to a FVCM software anomaly. Code U0121 will set and be moved to history in the FVCM with each ignition cycle.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.