2022 Ford F-250 SD Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 242, ordered newest first. Dated records on this page: Sep 20, 2023–Aug 12, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 12, 2026Service Bulletin/Repair Instructions
TSB 26-2375
NHTSA communication ID: 11036283
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 26-2050 to increase the labor operation allowance of labor operations A and B. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2704 and P0771 stored in the PCM/TCM. This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. Additional model information: 6.7L Diesel Engine 2022-2024 F-550 or F-600 F-Super Duty vehicles built on or before 15-May-2024 with over 5,000 miles (8,000km)
Source components: ELECTRICAL SYSTEM · ENGINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 25M01 Certain 2021 Model Year F-150 3.0L Diesel Engine and 2020-2022 Model Year Super Duty with 6.7L Diesel Engine Nitrogen Oxide (NOx) Sensor Replacement, If Required After Dealer Evaluation Reference: Emissions Recalls 22E02, 22E04, 23E01, and 25E09
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NEW VEHICLE DEMONSTRATION / DELIVERY HOLD Emissions Recall 25E09 Certain 2022 Model Year F-250 - F-600 Vehicles with 6.7L Engines Powertrain Control Module Programming and Particulate Matter Sensor Installation
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2022 Model Year F-250 - F-600 with 6.7L Diesel Engines One-Time Replacement for Diesel Particulate Filter Assembly Failures, If Required After Dealer Evaluation
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2572 to update the Parts List to correct the part number LC3Z-6006-L to LC3Z-6781-A, remove the flex plate bolts AL3Z-6379-BA from the parts list as these bolts are in kit LC3Z-6781-A, update the claim quantity of the part number W709771-S440 to 9 pieces (F-650/F750-Engine Replacement), W706447-S437 and W715068-S437 to 4 pieces, W712861-S439 to 8 pieces(F-Super Duty Pickup And Chassis Cab-Engine Replacement) / 8 pieces (F-53 Motorhome/F-59 Stripped Chassis Cab/F-650,F750 Engine Replacement) / W714286-S442 to 4 pieces (F-Super Duty Pickup And Chassis Cab-Camshaft and Tappet Repair / F-Super Duty Pickup And Chassis Cab-Engine Replacement), include LC3Z-6020-A for the Engine replacement lists, include 1 fuel injector seal kit to the Camshaft and Tappet repair lists, include 4 pieces of W520114-S440 to the E Series-Camshaft and Tappet Repair list, and update the engine oil part numbers XO-5W30-Q1SP and CXO-5W30-LSP6. Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing ro
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 22N05 - Supplement #3 Certain 2022 Model Year Super Duty with 6.7L Diesel Engine One-Time Replacement for Diesel Particulate Filter Assembly If Required After Dealer Evaluation
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2549. Reason for update: To add 2020 model year chassis cab vehicles. Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to the software in the PCM. This condition does not affect vehicle drivability or durability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Emission Recall 23E01 - Supplement #1 2021 Model Year F-150, 2022 Model Year Super Duty and 2023 Model Year F-650 / F-750 Truck Vehicles Equipped with Diesel Engines Powertrain Control Module Reprogramming
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 22N05 - Supplement #2 Certain 2022 Model Year Super Duty with 6.7L Diesel Engine One-Time Replacement for Diesel Particulate Filter Assembly If Required After Dealer Evaluation
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Source components: BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING · BACK OVER PREVENTION: WARNINGS · LANE DEPARTURE: BLIND SPOT DETECTION · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 F-150 vehicles equipped with a 5.0L/5.2L engine, 2021-2025 F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis vehicles equipped with a 6.8L/7.3L engine and 2021-2025 E-Series/F-650/F-750 vehicles equipped with a 7.3L engine may exhibit a rattle/scraping noise upon startup that may remain after the engine is running. Workshop Manual (WSM),
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2249 to update the claim quantity of the torque converter nuts, part number and claim quantity of the front support assembly bolt washers, and part number change of the fluid pan from the Parts List. Some of the vehicles listed in the Model statement above may exhibit a harsh reverse to drive engagements with no diagnostic trouble codes (DTC). This may be due to sticking valves in the main control valve body and/or damaged input shaft seals (F9), and the output shaft seals (F10). Additional model information: Built On Or Before 13-Dec-2021 10R140 Automatic Transmission
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various connectivity concerns with The Ford App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2142 to update the Parts List, Service Procedure (Steps 1-2), and increase the labor operation allowances to reprogram the PCM/TCM. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2704 and P0771 stored in the PCM/TCM. This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. Additional model information: 6.7L Diesel Engine 2022-2024 F-550 or F-600 F-Super Duty vehicles built on or before 15-May-2024 with over 5,000 miles (8,000km)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2026 F-Super Duty vehicles may exhibit a pull/drift condition during braking. This may be due to the brake pads needing to be broken in. Repeated, heavy brake applications may assist to resolve the pull/drift condition. The Workshop Manual, Section 206-00 Symptom Chart for vehicle pulls or drifts during braking has been updated to reflect this information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2322 to update the Service Procedure, Labor Operations and Parts List. Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L/3.5L (non hybrid)/6.8L/7.3L engine and 2021-2026 E-Series may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated to address this condition. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
Source components: ENGINE · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2119 to update the vehicles affected, parts list, and Service Procedure. Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to the software in the PCM. This condition does not affect vehicle drivability or durability.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150 vehicles equipped with a 5.0L/5.2L engine, 2021-2025 F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis vehicles equipped with a 6.8L/7.3L engine and 2021-2026 E-Series/F-650/F-750 vehicles equipped with a 7.3L engine may exhibit a rattle/scraping noise upon startup that may remain after the engine is running. This may be due to the starter motor drive gear not retracting after starting. To correct this condition, inspect the starter motor drive gear and shaft. If the starter motor drive gear slides back and forth by hand and/or shows signs of scoring or damage, replace the starter motor following Workshop Manual (WSM), Section 303-06 Starting System > Removal and Installation > Starter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2025 F-150 and 2018-2026 F-Super Duty vehicles equipped with a tailgate step may exhibit a step assembly that binds/will not open or opens/pops up while driving. This could be due to an incorrect adjustment of the tailgate step assembly. Before replacing any components for this concern, follow the revised Tailgate Step Adjustment procedure in Workshop Manual (WSM), Section 501-04.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0128 stored in the powertrain control module (PCM). This may be due to the software in the PCM.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L,3.5L EcoBoost (non-hybrid), 3.5L Cyclone, 6.8L or 7.3L engine, may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2026 F-Super Duty vehicles equipped with a 6.7L engine may require various repairs and/or maintenance to the fuel system where quick release couplings are utilized, such as the secondary fuel filter. The Workshop Manual (WSM), Section 310-00 > General Procedures > Quick Release Coupling has been updated to include videos and instructions of proper disconnect/connect steps involving the Type 27 quick release couplings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2021-2025 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit "Please Check Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
Source components: UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2019-2024 Ford and Lincoln vehicles equipped with SYNC 3 may experience a partially or fully black center display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2200 to update the parts list to add the new camshaft and tappet service kit and add F-650/F-750. Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During initial vehicle production, the Particulate Matter sensor (PM) was not installed on your vehicle due to a component supply shortage. The part is now available for installation. Additionally, the Nitrogen Oxides (NOx) sensor preheat is not functional in the powertrain calibration. Under certain conditions, this can lead to thermal shock and sudden failure of the NOx sensor
Campaign / software reference: 22E02
Source components: FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford/ Lincoln vehicles equipped with SYNC4 may not be able to perform an update to the accessory protocol interface module (APIM). This may be due to the software in the APIM. Ford Engineering has de-activated the ability to update these SYNC4 APIM modules as applicable, and the Ford Diagnosis and Repair System (FDRS) will not present an update for the APIM module. Some existing directed repairs may be impacted, check Professional Technician System (PTS) before attempting any specific technical service bulletin (TSB)/special service message (SSM) and check field service action (FSA) landing pages before attempting any FSA repairs. For any vehicle repairs requiring a software update that includes an APIM update in the programming sequence, if the 5-digit product code for the APIM software is equal to or lower than 23187, do not attempt to update affected modules at this time. To determine the 5-digit product code for the APIM software on the vehicle, while the vehicle center display screen is powered up with ignition in run or accessory, go to Settings > General > About SYNC.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2076 to update the powertrain control module (PCM) software level addressing the condition. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM). The vehicle may also exhibit a slight running rough condition at idle. This may be due to incorrect learned values in the PCM from operating the vehicle at altitudes greater than 2500 feet (762 meters) above sea level. This condition does not affect vehicle drivability or durability.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 F-Super Duty vehicles equipped with a 10R140 automatic transmission may exhibit a delayed engagement into drive and/or reverse on initial start-up. The condition may occur at times after sitting overnight or for a couple of days. This may be due to the transmission fluid draining back from the torque converter. This is a normal characteristic of the 10R140 transmission and has no effect on durability, do not attempt to repair. Advise the customer to allow more time after first engine start-up and before shifting into gear allowing time for the torque converter to refill.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 F-Super Duty vehicles equipped with a 10R140 transmission may exhibit harsh or delayed engagement/shift concerns. Refer to Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing for normal diagnostics. The WSM has been updated with all information from previously published articles related to this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2025 Ford or Lincoln vehicles may exhibit DTCs B142E:78, B1432:78, and/or B1433:54 diagnostic trouble codes (DTCs) in the CCM. This may be due to non-factory sized tires that may cause inaccurate speedometer readings that can impact the functionality of the CCM. When a vehicle is modified in this manner, replacement or realignment of the CCM may impact the normal operation of the system and/or performance of radar and camera-based features. Repair or replacement of the CCM when a vehicle is equipped with non-factory size tires may not be warrantable and subject to chargeback.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to the software in the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quality improvements include: -Improved error logging and fault recovery for the Battery Health, Wheel Alignment, Wheel Vibration, and Key off load monitors.
Campaign / software reference: 24-OTA SU 6.4.0 Super Duty (F-250, F-350, F-450, F-550)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 F-Super Duty vehicles may exhibit a Trailer Brake System Fault" message with diagnostic trouble code (DTC) U0131 stored in the trailer module (TRM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) U3012 only stored in the powertrain control module (PCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 F-Super Duty vehicles equipped with a 12.3 inch center display screen and 2023-2024 F-Super Duty vehicles may exhibit DTCs B1D08 and/or B1D09 stored in the trailer module (TRM) with a "Trailer Brake System Fault See Manual" message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) when operating at elevations greater than 2500 feet (762 meters)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine and rear wheel drive (RWD) may require replacement of the transmission assembly for various reasons.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In affected vehicles, the Variable Displacement Oil Pump (VDOP) delivers oil to the engine at low pressure/capacity during idle conditions. Routine occurrences of prolonged idle time may result in excess wear to the engine camshaft lobes and valve tappet surfaces due to reduced lubrication. Over time, the engine may progressively run rough due to cylinder misfire. Additionally, customers may hear engine tapping noises and the Check Engine Light (CEL) may illuminate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In affected vehicles, the Variable Displacement Oil Pump (VDOP) delivers oil to the engine at low pressure/capacity during idle conditions. Reason for supplement: software now available/additonal technician information
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2024 Ford and Lincoln vehicles equipped with a telematics control unit module (TCU) may exhibit the Location toggle button in the Connectivity setting menu grayed out with an inability to switch it off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2087 to update the Part List. Some 2020-2022 F-Super Duty vehicles equipped with a 10R140 automatic transmission may exhibit harsh reverse to drive engagements without diagnostic trouble codes (DTCs). This may be due to sticking valves in the main control valve body or suspect input shaft seals (F9) and the output shaft seals (F10). To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the E and F clutches and if necessary, replace the input shaft seals (F9) and the output shaft seals (F10).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 F-Super Duty pickup vehicles equipped with a 6.7L engine, 175 inch wheelbase, and built on or before 23-Sep-2021 may exhibit a thump/whine/knock noise from the midship fuel tank at idle or during key on, engine off (KOEO) after performing TSB 21-2057. The noise may be more pronounced at fuel levels at or below 1/4 tank. This may be due to the fuel pump
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2018 - 2024 Model Year Various Vehicles Update SYNC Software In all the affected vehicles, due to an error in the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2020-2024 Super Duty and 2021-2025 Model Year Econoline Equipped With a 6.8L or 7.3L Gasoline Engine Powertrain Control Module (PCM) Software Update REASON FOR THIS SUPPLEMENT • Software Availability Update: Software is now available to repair 2021-2022 and 2025 Model Year Econoline vehicles. The service action has been updated accordingly. • Technical Information: IDS programing information has been added for 2021-2023 Model Year Econoline Vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various FordPass/LincolnWay connectivity concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2020-2024 Super Duty and 2021-2025 Model Year Econoline Equipped With a 6.8L or 7.3L Gasoline Engine Powertrain Control Module (PCM) Software Update In affected vehicles, the Variable Displacement Oil Pump (VDOP) delivers oil to the engine at low pressure/capacity during idle conditions. Routine occurrences of prolonged idle time may result in excess wear to the engine camshaft lobes and valve tappet surfaces due to reduced lubrication. Over time, the engine may progressively run rough due to cylinder misfire. Additionally, customers may hear engine tapping noises and the Check Engine Light (CEL) may illuminate
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2376 to update the Part List and the Service Procedure. Some 2022-2024 F-550 and F-600 F-Super Duty vehicles equipped with a 10R140 automatic transmission and 6.7L diesel engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the transmission control module (TCM) with poor shift quality and over 5,000 miles (8,000 km) in service. This may be due to wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. To correct this condition, follow the Service Procedure to replace the E clutch hub and input shaft O-rings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the E clutch hub (7P211) on 2020-2024 F-Super Duty and 2024-2025 F-650/F-750 vehicles equipped with a 10R140 transmission, a new washer (7482) has been added and must be installed with the new updated E clutch hub. Refer to the Workshop Manual (WSM), Section 307-01B for proper installation of the washer. Refer to the parts catalog for the appropriate part numbers for the E clutch hub and the washer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 F-Super Duty vehicles built on or before 31-Oct-2022 and equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2201, P2209, P220E and/or P24FE stored in the powertrain control module (PCM). This may be due to the software in the PCM and the nitrogen oxides (NOx) sensor 11. To correct the condition, follow the Service Procedure to replace the NOx sensor 11 and reprogram the PCM and transmission control module (TCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 F-Super Duty vehicles equipped with a 12.3 inch center display screen and 2023-2024 F-Super Duty vehicles may exhibit DTCs B1D08 and/or B1D09 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Disconnect connector C4099 from the back of the trailer tow connector (14489). Inspect connector C4099 and the mating socket on the back of the trailer tow connector for signs of corrosion or damage. If corrosion or damage is present at either connector, replace both the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 13A576 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 F-Super Duty vehicles built on or after 01-Oct-2022 may exhibit the power running boards settings intermittently changing from AUTO to OFF without any driver input. This may be due to the software in the running board control module (RBM). To correct the condition, reprogram the RBM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14C177 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble code (DTC) U3012 stored in the PCM. If no drivability concerns or other DTCs are present, perform normal diagnostics per the Workshop Manual (WSM). If diagnostics lead to the powertrain control module (PCM) or body control module (BCM), the replacement of the PCM and/or the BCM will not resolve this concern. This illuminated MIL with DTC U3012 does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 F-Super Duty vehicles equipped with a 12.3 inch center display screen and 2023-2024 F-Super Duty vehicles may exhibit DTCs B1D08:11 and/or B1D09:11 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Inspect connector C4099 and the trailer tow connector (14489) for signs of corrosion or damage. If corrosion or damage is present at either connector, replace the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 14489 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2024 F-Super Duty vehicles are equipped with XL-22 (WSS-M2C184-A1) high temperature power steering fluid that looks like clear hydraulic fluid. This fluid is an improvement in high temperature and thermal oxidative stability compared to Mercon LV. This power steering fluid is also compatible and highly recommended to use when filling or topping off power steering systems of all 2012-2023 F-Super Duty vehicles originally equipped with Mercon LV.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may require a long block replacement of the engine for various reasons. The replacement long block may be equipped with an updated upper oil pan. If the oil filter adapter from the original engine does not mate with the new upper oil pan, service parts PC3Z-6881-A (oil filter adapter), W503277-S439 (package of 6 bolts, 4 bolts required), W718564-S450 (stud), W520101-S442 (nut), and PC3Z-14A206-A (starter cable retaining bracket) will be needed to complete the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Ford and Lincoln vehicles equipped with SYNC 4 may exhibit the navigation feature in the center display screen only displaying imperial (feet and miles) units and not being able to change to metric (meters and kilometers) units. This may be due to the software level of the SYNC module (APIM). To correct this condition, follow the Service Procedure to update the APIM to the latest software level via a coordinated flash. NOTE: The APIM software update that addresses the symptom listed in this article may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 23B24 Certain 2022 Super Duty and 2023 F-Series Models with Tailgate Step - Inspection of Tailgate Step Handle and Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 F-Super Duty vehicles equipped with BLIS/CTA may exhibit fault messages with DTC B11D6:15 stored in the side obstacle detection control left/right (SODL/SODR) module. To correct the condition, replace the affected SODL/SODR module. Refer to Workshop Manual, Section 419-04. For claiming, use causal part 14C689.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the transmission case on a 2020-2022 F-Super Duty equipped with a 10R140 transmission, the new service case may not come equipped with the transmission fluid leveling plug. To achieve proper transmission fluid level, a new transmission fluid pan and gasket must be installed (service part PC3Z-7A194-A). Refer to the 2023 F-Super Duty Workshop Manual, Section 307-01B to properly set the transmission fluid level when using the newer transmission fluid pan.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.