2019 Chrysler PACIFICA Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 501, ordered newest first. Dated records on this page: Apr 2, 2022–Jan 12, 2024.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jan 12, 2024Service Bulletin/Repair Instructions
ReferenceY40
NHTSA communication ID: 10251816
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification Y40 Control Module Software Updates
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Internal Transmission Wiring Connector Short Warranty Extension XN1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SWITCH AND BEZEL Front Door In any case that after following the service procedures it is determined that the switch is faulty. Please do not try to open the Switch nor fix it. Just return the part and order a new one.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:DOOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SWITCH AND BEZEL Front Door In any case that after following the service procedures it is determined that the switch is faulty. Please do not try to open the Switch nor fix it. Just return the part and order a new one.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:DOOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM:PUMP.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Internal Transmission Wiring Connector Short Warranty Extension XE1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
NHTSA source summary · Original PDF not reviewed by Recallfolio
PSU right intake camshaft Case 1) If you are to flash the PSU (Pentastar Upgrade Engine) PCM due to P0300 code presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ROCKER ARM ASSY - ROLLER ROCKER Case 1.- Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Internal Transmission Wiring Connector Short Warranty Extension XE1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
Source components: BACK OVER PREVENTION · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air JR34.3 Updating to JR34.32.Software Version Customers may experience one or more of the following: Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAR and UCR Radio Enhancements Customers may experience one or more of the following: **Wi-Fi hotspot connection failure. Speaker popping, crackle noise during Voice Recognition (VR) response. Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** Lost radio presets. High pitch chime noise. Contact list not loading. Remote app inoperative. High pitch squeal, pop or humming sound coming from all of the speakers. Backup camera gridlines missing. Radios resets when a wireless connectivity paired phone receives two text messages one after another simultaneously after approximately seven seconds. (Sales Code ABD). Speaker crackling noise. Unable to adjust volume. Radio may reset /reboot, turn itself off and then back on. Active call not transferred to vehicle wireless connectivity. Voice Recognition (VR) not understanding commands. Wireless connectivity phonebook not available. Anti-theft code request message. Lines appear across screen. Radio will not switch modes between AM, FM, SAT or Media. Poor wireless connectivity sound quality. Phone pairing issues. In addition, the following enhancement is included in this update: Wireless connectivity pair or connection improvements. This bulletin involves inspecting and if required, updating the radio software level to **40.1. Depending on the radio?s current software level the radio may need a one or two USB update.**
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAV and UCV Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Lost radio presets. ? SXM favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Lost navigation settings. ? SXM icon inoperative (D-Truck). ? Radio display screen is black when the ignition is on (Rear View Camera (RVC) not affected (D-Truck)). ? Radio freeze intermittent (RVC not affected (D-Truck)). ? Wireless connectivity pair or connection issue (D-Truck). ? Radio channel changes by itself (D-Truck). ? Backup camera has black display screen, or Only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) (D-Truck). ? High pitch chime noise (D-Truck). ? Contact list not loading (D-Truck). ? ?Device Not Supported? message (D-Truck). ? Remote app inoperative (D-Truck). ? Travel-Link fuel price incorrect (D-Truck). ? Backup camera gridlines missing (D-Truck). ? Unable to adjust volume (D-Truck). ? Radio may reset/reboots, turn itself off and then back on again (D-Truck). ? High pitch squeal, pop or humming sound coming from all of the speakers (WK RU Only). ? Radio display screen is black, intermittent (RVC not affected (WK RU Only)). ? Radio freeze intermittent (RVC not affected (WK RU Only)). ? Navigation stuck on loading screen or not appearing at all (WK RU Only). ? Radios resets when a wireless connectivity paired phone receives two text messages one after another simultaneously after approximately seven seconds. (ABD sales code). ? Speaker crackling noise on non amplified vehicles (WK RU, UAV Only). ? Active cal
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · PARKING BRAKE · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Software Version Update to 22.66 This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from IR22.64 and IR22.65 to IR22.66. The national launch for the FOTA is expected to begin on January 09, 2023. ? Wi-Fi hotspot connection not working. ? No internet connection message on the phone when trying to connect to a device
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LATCH, Sliding Door (Right / Left) For any RU vehicle with presence of a B2500 fault code (active / stored / pending), please refer to the following steps: 1. Please verify proper functionality of both sliding doors (power or manual) through all inputs (overhead console, key fob, handle grab). 2. If sliding doors operate as expected, do NOT replace sliding door latch(es). 3. If service is required, and your Dealership is located in the Detroit Metro Area please contact FCA Redacted Content, prior to replacing any sliding door latch(es). If no response in 15 minutes, proceed with repair. 4. If possible, please provide any / all information in the repair order narrative regarding status of sliding door function (i.e, door only works manually, won't open via key fob, etc.). This includes all customer feedback as well (what exactly brought the customer into the dealer).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs. P0A2D-00 - Drive Motor ?A? Temperature Sensor ?A? Circuit High. P0A33-00 - Drive Motor B Temperature Sensor 1 Circuit High. Technicians and/or customers may also report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Customers may also experience: Noise or vibration heard/felt during a gas engine start in park. This software release includes the following software enhancement: Corrections to allow the vehicle to clear the permanent fault codes. Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this PCM update:Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS). Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1AF8-00 - MCPA Control Module Shutdown Performance. P1AFE-00 - MCPB Improper Shut Down.P1AF8-00&P1AFE-00 will now be set as a 1 trip failure instead of a 2 trip failure. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P0A46-00 - Drive Motor B Position Sensor 1 Circuit Range-Performance. P0A40-00 - Drive Motor A Position Sensor 1 Circuit Range-Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P0CF3-00 - Control Pilot Circuit Open. P0A44 - Drive Motor A Position Sensor 1 Circuit Overspeed. U0111-00 - Lost Communication With Battery Energy Control Module (BPCM). P1625-00 - Park Pawl System Failure. U0412-00 - Invalid Data Received From Battery Energy Control Module-A. P215B-00 - Vehicle Speed Output Shaft Speed Correlation. P079A-00 - Transmission Friction Element 1 Slip Detected. P079B-00 - Transmission Friction Element 2 Slip Detected. Customers may also comment:Vehicle will not start when temperature is -30° C (-22° F) and below. Heard and/or felt bump when the gas engine turns on while driving. Vehicle will not charge beyond 98%. "Service Charging System" and "Traction Battery Cutoff" warning messages appear during a key cycle event at -7° C (+20°F). Vehicle will force to Park when keyed off in Neutral if the door is open
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.