2017 Chevrolet SUBURBAN Manufacturer communications & TSBs.Page 15
Original record summaries, dates and identifiers for this model-year. Records 1,401–1,500 of 1,559, ordered newest first. Dated records on this page: Sep 1, 2016–Dec 23, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Dec 23, 2016Service Bulletin/Repair Instructions
PIP4828C
NHTSA communication ID: 10111736
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a rough idle and/or momentary lack of power after cold starting the engine and immediately placing the transmission in gear. Technician should follow published Service Information diagnostics first. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is ending the need for information from the field on vehicles that have the condition of rear auxiliary a/c not cooling or blowing warm air.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
Source components: BACK OVER PREVENTION · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are equipped with Hands Free Power Lift-gate Regular Production Option Code (TC2). Some customers may experience problems with the activation of the lift-gate hands free operation. Dealer will communicate to the customer some tips on the Hands free Lift-gate. The remote keyless entry FOB must be within 3 feet or 1 meter from the bumper. The foot kick is conducted at the direct center of the length of kick zone.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communication provides information to the technician about vehicles with the rear body fuse block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the main power buss bar has poor terminal tension.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory 22" 6-Spoke Split Chrome Wheels Regular Production Option Code (SEU) or during any service requiring wheel removal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about owners that want the auto door lock disabled. There is no avalible setting or Body Control Module calibration to turn off the auto door locks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and re-pair any phones that were deleted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
Source components: ELECTRICAL SYSTEM · ELECTRONIC STABILITY CONTROL (ESC) · STEERING · TIRES · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to repair information to correct a customer concern of the hood fluttering, vibrating or displaying visible motion at highway speeds or over rough road surfaces.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when adjusting the Heater-Vent-Air Conditioning controls the Heater-Vent-Air Conditioning display is blank and/or various selections missing from radio Settings menu intermittently. Technicians will find the Heater-Vent-Air Conditioning does change but the lower radio display is blank. Technician will need to update the radio using Service Programming System with the latest software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a MIL or a engine misfire due to a loose spark plug wire.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track l
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a rattle noise from the second row seat. Technician will need to inspect the striker not aligned properly in latch opening. To repair this condition, rework/adjust the striker in the direction to center it in the latch opening. An adjustable wide mouth metal working tool may be used to adjust the striker just enough to center in the latch opening. Technician may find a seat bottom latch may have an unequal latch opening side-to-side for the striker to seat into. To repair this condition, with the affected seat in the tumbled forward position, while applying steady, firm pressure, cycle the seat down into the latched position. Some vehicles built prior to 09/21/2015 with 60/40 Split Bench Seat may have 60-percent long side bench, inboard latch may not be properly aligned in striker opening. Technician will need to place a 2.6 mm thick flat washer over the 40 percent seat base stud, not the floor stud. Some vehicles may have a seat base plat that rattles against the rib in the floor pan. Apply Mylar tape to the floor pan under the seat plate to provide relief for the rattle condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that show a "Take Steering" message on the Driver Information Center along with a warning chime/alert. Dealer should be advised the purpose of the message is to alert the driver that the Lane Keep Assist system has not detected active steering input from the driver (hands off the steering wheel).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the BCM on select vehicles that are listed by VIN due to an error in the security system that does not allow the BCM to be reprogrammed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
Source components: BACK OVER PREVENTION · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have "Service Theft System" message on the Driver Information Center. Technician may find Diagnostic Trouble Code B291B sym 3B and is unable to clear the Diagnostic Trouble Code. Technician will need to restore communication between the Body Control Module and Theft Deterrent Sensor Module to clear the Diagnostic Trouble Code.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
Source components: ELECTRONIC STABILITY CONTROL (ESC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin aids the technician on diagnosing possible vibrations in a vehicle, methods used for testing each scenario and documenting findings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine, transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an Instrument Panel Cluster that will have the correct miles per hour, when ?Teen Driver? is set the radio will show a lower miles per hour on the radio display. Dealer should advise the customer that engineering is currently investigating a solution.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The information in this bulletin details the proper configurations for the ignition key, fob, key tags and key rings and applying a QR code sticker or barcode sticker to a key fob.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Thins engineering informational bulletin is requesting information from the field on vehicles that have the condition of rear auxiliary a/c not cooling or blowing warm air.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT HAVE A CHECK ENGINE MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P0747 AND OR P0796. DEALER SHOULD ADVISE THE CUSTOMER ENGINEERING IS CURRENTLY INVESTIGATING A SOLUTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P0106 AND P0506. TECHNICIAN WILL INSPECT FOR A BROKEN VALVE SPRING AND REPLACE AS NEEDED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON THE TIRES SUPPLIED WITH A NEW VEHICLE ARE COVERED BY GENERAL MOTORS AGAINST DEFECTS IN MATERIAL OR WORKMANSHIP UNDER THE BUMPER-TO-BUMPER NEW VEHICLE LIMITED WARRANTY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES WITH AN INTERMITTENT LOSS OF GRIDLINES IN THE REAR CAMERA DISPLAY SCREEN AND A "SERVICE REAR VISION SYSTEM" MESSAGE THAT BOTH HAPPEN AT THE SAME TIME. TECHNICIAN SHOULD CHECK FOR DIAGNOSTIC TROUBLE CODES AND FOLLOW PUBLISHED SERVICE INFORMATION DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODES. IF NOT DIAGNOSTIC TROUBLE CODES STORED AND THE CONCERN WAS DUPLICATED OR THE CUSTOMER DESCRIBED THE CONCERN, DEALER SHOULD COMMUNICATE TO THE CUSTOMER THAT WE APOLOGIZE FOR THIS INCONVENIENCE AND THAT GENERAL MOTORS IS CURRENTLY EVALUATING THIS CONCERN.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT GENERAL MOTORS AND GENERAL MOTORS OF CANADA COMPANY DO NOT SUPPORT CROSS BORDER SALES. THE GENERAL MOTORS OF CANADA CUSTOMER CARE CENTRE IS THE SOLE AUTHORIZED PROVIDER OF A CERTIFICATION CONFIRMATION LETTER WHICH HELPS OUR CUSTOMERS IDENTIFY IF THEIR VEHICLES MEETS THE REQUIRED USA REGULATORY STANDARDS NECESSARY FOR IMPORTATION INTO THE USA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT HAVE A CHECK ENGINE MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P0747 AND OR P0796. DEALER SHOULD ADVISE THE CUSTOMER ENGINEERING IS CURRENTLY INVESTIGATING A SOLUTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR VEHICLES WITH A ROUGH IDLE AND/OR VIBRATION AT IDLE IN DRIVE. THIS CONDITION WILL NOT BE PRESENT IN PARK, OR NEUTRAL. THIS CONCERN MAY BE CAUSED BY GROUND OUT WITHIN THE ONE OR BOTH ENGINE MOUNTS. TECHNICIAN WILL USE CH-51450-A (PICO OSCILLOSCOPE) TO MEASURE THE VIBRATION DISTURBANCE. IF THE VIBRATION CONCERN IS E1.5 IN THE HORIZONTAL / LATERAL DIRECTION WITH PICO SENSOR MOUNTED IN SEAT TRACK AS INDICATED CONTINUE WITH STEPS TO REDUCE THE AMPLITUDE OF THE VIBRATION BY ADDING SPACERS IN KEY LOCATIONS TO REDUCE GROUND OUT WITHIN THE ENGINE MOUNTS. THE 6.2L ENGINE HAS A CHARACTERISTIC E1 WHICH CAN BE FELT, AND MAY BE DESCRIBED AS A LOPEY IDLE. DO NOT CONFUSE 6.2L E1 CHARACTERISTIC (NOT CAUSED BY MOUNT GROUND-OUT), WITH E1.5 NORMAL IDLE CHARACTERISTICS BEING TRANSMITTED INTO THE TRUCK VIA GROUND-OUT THRU THE ENGINE MOUNTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS ON DIAGNOSING AND REPAIRING VEHICLES THAT MAY HAVE UNWANTED GRADE BRAKING, REDUCED ENGINE POWER WITH NO DRIVER INFORMATION CENTER MESSAGES BRAKE PEDAL OVERRIDE FEATURE , TRANSMISSION BUSY OR FREQUENT SHIFTING UP OR DOWN, AND DIAGNOSTIC TROUBLE CODES P057B, P057C, AND/OR P057D MAY OR MAY NOT BE SET. TECHNICIAN WILL USE THIS PRELIMINARY INFORMATION TO FIND THE BRAKE PEDAL POSITION DATA PARAMETERS IN THE SCAN TOOL, AND ALSO TO PROVIDE SOME ADDITIONAL DIAGNOSTIC HELP. THESE ISSUES MAY BE CAUSED BY AN INCORRECT BRAKE PEDAL POSITION SENSOR INPUT TO THE ENGINE CONTROL MODULE. TECHNICIAN WILL VERIFY WITH THE SCAN TOOL IF THE ENGINE CONTROL MODULE HAS THE CORRECT PARAMETERS FOR THE BRAKE PEDAL POSITION SENSOR. IF AN ENGINE CONTROL MODULE BRAKE PEDAL POSITION SENSOR RELEARN IS PERFORMED, THE TRUCK MAY BE TEMPORARILY REPAIRED UNTIL THE INTERMITTENT WIRING ISSUE BETWEEN THE ENGINE CONTROL MODULE AND BRAKE PEDAL POSITION SENSOR OCCURS AGAIN. ON 2014 AND NEWER TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X115 AND X119. ON THE 2014 AND PREVIOUS TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X205.
Source components: ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL · ENGINE · PARKING BRAKE · POWER TRAIN:AUTOMATIC TRANSMISSION · SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE SPEEDOMETER INACCURATE READS 5 MPH WHEN TRAVELING 50 MPH. ENGINEERING IS WORKING TO DEVELOP A SOLUTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE THE ONSTAR WIRELESS FIDELITY INOPERATIVE. TECHNICIAN WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER WITH A SCAN TOOL CONNECT TO THE VEHICLE FOR FURTHER ASSISTANCE.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT CUSTOMERS THAT MAY REQUEST THE FACTORY INTEGRATED TRAILER BRAKE CONTROLLER REGULAR PRODUCTION OPTION CODE (JL1) BE INSTALLED ON THEIR FULL-SIZE PICKUP OR SUV WHEN THE VEHICLE WAS NOT ORDERED WITH THE OPTION. DEALER SHOULD ADVISE THE CUSTOMER IT CANNOT BE ADDED TO THE VEHICLE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES VOICE RECOGNITION INOPERATIVE FOR CALLING BLUETOOTH PHONE CONTACTS. TECHNICIAN WILL NEED TO CLEAR ALL PRIVATE DATA AND REPAIR ANY PHONES THAT WERE DELETED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS DIAGNOSTIC TOOL KIT (EL-51578) HAS BEEN RELEASED TO HELP DIAGNOSE ANY OF THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS CONCERNS. THE KIT CONTAINS HEADER CONNECTORS THAT ARE INSTALLED TO BYPASS MEDIA ORIENTED SYSTEMS TRANSPORT BUS MODULES. THE BYPASS CONNECTOR ALSO CONTAINS A TERMINAL FOR VERIFYING MEDIA ORIENTED SYSTEMS TRANSPORT CONTROL CIRCUIT VOLTAGES. TECHNICIAN SHOULD REVIEW MEDIA ORIENTED SYSTEMS TRANSPORT BUS DESCRIPTION AND OPERATION AND DIAGNOSTIC TROUBLE CODE U0028 DIAGNOSTIC PROCEDURES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATES THAT WHEN CUSTOMER OR TECHNICIAN MAY INDICATE WHEN ATTEMPTING TO ADD A NEW TRANSMITTER TO A VEHICLE FOLLOWING THE ADDING TRANSMITTERS WITHOUT SERVICE PROGRAMMING SYSTEM PROCEDURE. THE PROCEDURE WILL NOT COMPLETE AND A MESSAGE "REMOTE LEARN PENDING" WILL BE DISPLAYED ON THE DRIVER INFORMATION CENTER. IN THE PAST TO PERFORM THE NEW TRANSMITTER PROCEDURE ONLY 1 PREVIOUSLY LEARNED TRANSMITTER WAS REQUIRED, THIS IS NO LONGER THE CASE NOW 2 PREVIOUSLY LEARNED TRANSMITTERS ARE REQUIRED AND PLACED INTO THE CUP HOLDER. IF THIS NEW PROCEDURE IS NOT FOLLOWED, THE "ADDING TRANSMITTERS WITHOUT SERVICE PROGRAMMING SYSTEM" CANNOT BE PERFORMED. THE TECHNICIAN WILL BE FORCE TO ADD A TRANSMITTER USING SERVICE PROGRAMMING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.