The manufacturer’s record · Page 11 of 16
Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 1,559, ordered newest first. Dated records on this page: Jan 17, 2018–Jun 12, 2018.
Back to 2017 Chevrolet SUBURBAN problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10143432
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10143432 at NHTSANHTSA communication ID: 10143430
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
Source components: STRUCTURE · SUSPENSION.
Source record 10143430 at NHTSANHTSA communication ID: 10143429
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10143429 at NHTSANHTSA communication ID: 10143428
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates and issue with an itch, rattle, flutter, squeak, tick, and/or chirp type noise coming from the left I/Por A-pillar area caused by contact between the drivers fender and A pillar.
Source components: STRUCTURE:FRAME AND MEMBERS.
Source record 10143428 at NHTSANHTSA communication ID: 10143424
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
Source components: ENGINE AND ENGINE COOLING.
Source record 10143424 at NHTSANHTSA communication ID: 10141380
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates information to have dealers contact TCSC for programming assistance with new amplifier part numbers until all the new amplifier numbers are setup correctly for programming.
Source components: EQUIPMENT.
Source record 10141380 at NHTSANHTSA communication ID: 10141379
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
Source components: EQUIPMENT · SEATS.
Source record 10141379 at NHTSANHTSA communication ID: 10141372
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: ELECTRICAL SYSTEM · PARKING BRAKE.
Source record 10141372 at NHTSANHTSA communication ID: 10141371
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10141371 at NHTSANHTSA communication ID: 10141370
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · STEERING.
Source record 10141370 at NHTSANHTSA communication ID: 10141367
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
Source components: ELECTRICAL SYSTEM.
Source record 10141367 at NHTSANHTSA communication ID: 10141365
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10141365 at NHTSANHTSA communication ID: 10141364
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10141364 at NHTSANHTSA communication ID: 10141351
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
Source components: FORWARD COLLISION AVOIDANCE.
Source record 10141351 at NHTSANHTSA communication ID: 10207716
NHTSA source summary · Original PDF not reviewed by Recallfolio
Special Coverage. Some vehicles may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.
Source components: ENGINE · POWER TRAIN.
Source record 10207716 at NHTSANHTSA communication ID: 10137599
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a normal characteristic.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10137599 at NHTSANHTSA communication ID: 10137528
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates aService Adaptive Cruise With DTC C018C SYM3A After Replacing K14 Distance Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.
Source components: ELECTRICAL SYSTEM.
Source record 10137528 at NHTSANHTSA communication ID: 10137526
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.
Source components: EXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH.
Source record 10137526 at NHTSANHTSA communication ID: 10137521
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL · POWER TRAIN.
Source record 10137521 at NHTSANHTSA communication ID: 10137597
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides information for rebuilding fuel injectors in the event of an underhood fuel odor and/or extended cranking condition.
Source components: FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS.
Source record 10137597 at NHTSANHTSA communication ID: 10137559
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on approved warranty part numbers for original equipment batteries.
Source components: EQUIPMENT.
Source record 10137559 at NHTSANHTSA communication ID: 10137514
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a power steering control module calibration error that does not allow its DTC's to transition to history and they always stay current, which can mislead a technician diagnosis. Dealers are to reprogram the power steering control module with updated calibration which will allow DTC's to transition to history if the issue that caused the DTC(s) are now longer present.
Source components: ELECTRICAL SYSTEM · STEERING.
Source record 10137514 at NHTSANHTSA communication ID: 10137556
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
Source components: ELECTRICAL SYSTEM.
Source record 10137556 at NHTSANHTSA communication ID: 10137589
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for engine oil life monitor operation calculation.
Source components: ENGINE AND ENGINE COOLING.
Source record 10137589 at NHTSANHTSA communication ID: 10137577
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the memory set module to correct a condition of Personalization Selections Intermittently Missing from Comfort and Convenience Menu due to a calibration concern.
Source components: ELECTRICAL SYSTEM.
Source record 10137577 at NHTSANHTSA communication ID: 10137570
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical bulletin provides information on new software to correct the rear camera display being too bright.
Source components: BACK OVER PREVENTION.
Source record 10137570 at NHTSANHTSA communication ID: 10137562
NHTSA source summary · Original PDF not reviewed by Recallfolio
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.
Source components: VISIBILITY:GLASS, SIDE/REAR.
Source record 10137562 at NHTSANHTSA communication ID: 10137558
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
Source components: EQUIPMENT.
Source record 10137558 at NHTSANHTSA communication ID: 10137554
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
Source components: POWER TRAIN.
Source record 10137554 at NHTSANHTSA communication ID: 10137560
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10137560 at NHTSANHTSA communication ID: 10137484
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical bulletin provides a procedure for radio replacement due to the radio tuner module being bad.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10137484 at NHTSANHTSA communication ID: 10137540
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical Bulletin provides information to correct a customer concern of a siren or whine noise from the in-tank fuel pump at temperatures below -6C or 20F, accompanied by start and stall, no start, loss of power and MIL illuminated. Technicians may find DTCs P0087, P018B, P228A, P228B or P2635 set in ECM.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10137540 at NHTSANHTSA communication ID: 10137561
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
Source components: STRUCTURE.
Source record 10137561 at NHTSANHTSA communication ID: 10137537
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim.
Source components: EQUIPMENT.
Source record 10137537 at NHTSANHTSA communication ID: 10137557
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
Source components: EQUIPMENT.
Source record 10137557 at NHTSANHTSA communication ID: 10137383
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10137383 at NHTSANHTSA communication ID: 10137209
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (L83), 5.3L (L86), 6.2L (LV3) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
Source components: ENGINE.
Source record 10137209 at NHTSANHTSA communication ID: 10137386
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · ELECTRICAL SYSTEM:12V/24V/48V BATTERY · EQUIPMENT.
Source record 10137386 at NHTSANHTSA communication ID: 10137207
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: BACK OVER PREVENTION: WARNINGS.
Source record 10137207 at NHTSANHTSA communication ID: 10137205
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a customer concern ofIPC gauges inoperative or fluctuate, No Start,No Crank,SIR Light / Service Airbag Message, Service Suspension Message,Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback,HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164,U0184, U0186, U0198, U0422. Dealer is instructed to check Serial Data Gateway Module X2 connector for terminal concerns and repair as needed.
Source components: ENGINE · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · STEERING · SUSPENSION.
Source record 10137205 at NHTSANHTSA communication ID: 10137203
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
Source components: ENGINE · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM.
Source record 10137203 at NHTSANHTSA communication ID: 10137202
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10137202 at NHTSANHTSA communication ID: 10137381
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
Source components: TIRES.
Source record 10137381 at NHTSANHTSA communication ID: 10137201
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle’s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.
Source components: ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL.
Source record 10137201 at NHTSANHTSA communication ID: 10137199
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.
Source components: WHEELS:LUGS/NUTS/BOLTS/STUDS.
Source record 10137199 at NHTSANHTSA communication ID: 10137197
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
Source components: ENGINE AND ENGINE COOLING.
Source record 10137197 at NHTSANHTSA communication ID: 10137420
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Phantom Three Beeps or Horn Chirps Heard After Turning Off Vehicle and that it should be considered normal.
Source components: ELECTRICAL SYSTEM:HORN · EQUIPMENT:ELECTRICAL.
Source record 10137420 at NHTSANHTSA communication ID: 10137380
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10137380 at NHTSANHTSA communication ID: 10137188
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
Source components: ENGINE.
Source record 10137188 at NHTSANHTSA communication ID: 10137182
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
Source record 10137182 at NHTSANHTSA communication ID: 10137385
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137385 at NHTSANHTSA communication ID: 10137306
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the drivers front door window regulator motor and door wiring harness if water and/or corrosion is found in the connectors.
Source components: ELECTRICAL SYSTEM:WIRING · STRUCTURE:BODY:DOOR · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
Source record 10137306 at NHTSANHTSA communication ID: 10137301
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides graphics, information and guidelines for engine component wear that require repair and not engine replacement.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137301 at NHTSANHTSA communication ID: 10137382
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137382 at NHTSANHTSA communication ID: 10137297
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
Source components: SERVICE BRAKES · WHEELS.
Source record 10137297 at NHTSANHTSA communication ID: 10137167
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
Source components: ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL.
Source record 10137167 at NHTSANHTSA communication ID: 10137166
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the alarm sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver’s door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver’s door remains open the alarm will not turn back on and the new transmitters can be programmed.
Source components: ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:CONTROL MODULE · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10137166 at NHTSANHTSA communication ID: 10137375
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
Source components: ELECTRICAL SYSTEM.
Source record 10137375 at NHTSANHTSA communication ID: 10137343
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
Source components: ENGINE.
Source record 10137343 at NHTSANHTSA communication ID: 10137283
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10137283 at NHTSANHTSA communication ID: 10137378
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10137378 at NHTSANHTSA communication ID: 10129895
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle has DTC P06DD setting. (This PI applies to vehicles that have either an original or replacement oil pump).The oil pump control solenoid may be damaged or broke.
Source components: ENGINE.
Source record 10129895 at NHTSANHTSA communication ID: 10129891
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle has DTC P06DD setting. (This PI applies to vehicles that have either an original or replacement oil pump).The oil pump control solenoid may be damaged or broke .
Source components: ENGINE.
Source record 10129891 at NHTSANHTSA communication ID: 10137344
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE.
Source record 10137344 at NHTSANHTSA communication ID: 10137374
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, possible battery drain concern.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS.
Source record 10137374 at NHTSANHTSA communication ID: 10137322
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the rear brake rotors to correct a condition of Squeak/Squeal Type Noise Heard at Low Speeds During Brake Apply due to moisture build up on the rotors.
Source components: SERVICE BRAKES, AIR:DISC:ROTOR · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR.
Source record 10137322 at NHTSANHTSA communication ID: 10137345
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137345 at NHTSANHTSA communication ID: 10129889
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Fender wheel-opening heights are related to, but distinct from, trim height. The front wheel-opening height is known as P height, and the rear wheel-opening height is known as R height. Adjust and heights that are out of specification. After all adjustments are done, perform a front-end alignment and check headlight aim.
Source components: STRUCTURE.
Source record 10129889 at NHTSANHTSA communication ID: 10137349
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year and provides technicians with repair information to correct a customer concern of rough, uneven or irregular horizontal seam on liftgate.
Source components: STRUCTURE:BODY:HATCHBACK/LIFTGATE.
Source record 10137349 at NHTSANHTSA communication ID: 10129881
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA.
Source record 10129881 at NHTSANHTSA communication ID: 10129879
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.
Source components: EQUIPMENT.
Source record 10129879 at NHTSANHTSA communication ID: 10129878
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
Source components: SUSPENSION:FRONT:SHOCK ABSORBER · SUSPENSION:REAR:SHOCK ABSORBER.
Source record 10129878 at NHTSANHTSA communication ID: 10129877
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.
Source components: ELECTRICAL SYSTEM · SUSPENSION:FRONT:SHOCK ABSORBER.
Source record 10129877 at NHTSANHTSA communication ID: 10129873
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10129873 at NHTSANHTSA communication ID: 10137323
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the memory set module to correct a condition of Personalization Selections Intermittently Missing from Comfort and Convenience Menu due to a calibration concern.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10137323 at NHTSANHTSA communication ID: 10129868
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesP0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
Source components: ENGINE.
Source record 10129868 at NHTSANHTSA communication ID: 10129862
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10129862 at NHTSANHTSA communication ID: 10137321
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides ECM reprogramming information to Correct DTC P2101.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE.
Source record 10137321 at NHTSANHTSA communication ID: 10129857
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
Source components: ELECTRICAL SYSTEM.
Source record 10129857 at NHTSANHTSA communication ID: 10137354
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Noise Originating from Front Shock/Strut While Accelerating, Stopping, or Traveling Over Bumps.
Source components: SUSPENSION:FRONT:MACPHERSON STRUT · SUSPENSION:FRONT:SHOCK ABSORBER.
Source record 10137354 at NHTSANHTSA communication ID: 10137341
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137341 at NHTSANHTSA communication ID: 10139283
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · EQUIPMENT.
Source record 10139283 at NHTSANHTSA communication ID: 10139279
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
Source record 10139279 at NHTSANHTSA communication ID: 10129102
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
Source components: ELECTRICAL SYSTEM.
Source record 10129102 at NHTSANHTSA communication ID: 10139282
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10139282 at NHTSANHTSA communication ID: 10137162
NHTSA source summary · Original PDF not reviewed by Recallfolio
17456 - Customer Satisfaction Program. Certain vehicles may have a condition in which the rear wheel hub nut could become loose due to the rear wheel hub nut retainer not being formed properly. If the hub nut loosens, the StabiliTrak message may be displayed in the driver information center (DIC) and the traction control indicator may illuminate, axle fluid may leak from the axle seal area, and rear axle housing damage could occur. Replace the hub nut retainer. Inspect the axle tube threads for damage and repair if necessary.
Source components: WHEELS:HUB.
Source record 10137162 at NHTSANHTSA communication ID: 10139273
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to install an A.C line support bracket to help reduce the resonance it produces from the A/C compressor at low speeds.
Source components: EQUIPMENT · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10139273 at NHTSANHTSA communication ID: 10139272
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information retaining to the fact that Service Manuals will now be available on USB.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10139272 at NHTSANHTSA communication ID: 10137263
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reinstall the rear defroster tab on the rear window defogger for vehicles with the condition of rear defrosters inoperative or if one is to break during a normal repair.
Source components: VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW.
Source record 10137263 at NHTSANHTSA communication ID: 10129097
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
Source components: ENGINE.
Source record 10129097 at NHTSANHTSA communication ID: 10129093
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: EXTERIOR LIGHTING.
Source record 10129093 at NHTSANHTSA communication ID: 10129091
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
Source components: ENGINE AND ENGINE COOLING.
Source record 10129091 at NHTSANHTSA communication ID: 10129089
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Source components: WHEELS.
Source record 10129089 at NHTSANHTSA communication ID: 10129088
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES.
Source record 10129088 at NHTSANHTSA communication ID: 10129084
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show “No Audio” in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10129084 at NHTSANHTSA communication ID: 10129082
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.
Source components: AIR BAGS · ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY · LANE DEPARTURE · POWER TRAIN · STEERING.
Source record 10129082 at NHTSANHTSA communication ID: 10129080
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION · SEAT BELTS · SERVICE BRAKES, HYDRAULIC · STEERING · WHEELS.
Source record 10129080 at NHTSANHTSA communication ID: 10129075
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
Source components: BACK OVER PREVENTION.
Source record 10129075 at NHTSANHTSA communication ID: 10129073
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Source components: ENGINE.
Source record 10129073 at NHTSANHTSA communication ID: 10139280
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
Source record 10139280 at NHTSA