The manufacturer’s record · Page 8 of 18
Original record summaries, dates and identifiers for this model-year. Records 701–800 of 1,780, ordered newest first. Dated records on this page: May 13, 2019–Nov 18, 2019.
Back to 2016 Chevrolet SILVERADO 2500 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10169315
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away.
Source components: ENGINE.
Source record 10169315 at NHTSANHTSA communication ID: 10169309
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides information for rebuilding fuel injectors in the event of an underhood fuel odor and/or extended cranking condition.
Source components: ENGINE · FUEL SYSTEM, GASOLINE.
Source record 10169309 at NHTSANHTSA communication ID: 10169298
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
Source components: POWER TRAIN.
Source record 10169298 at NHTSANHTSA communication ID: 10169356
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · TIRES · WHEELS.
Source record 10169356 at NHTSANHTSA communication ID: 10169354
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EXTERIOR LIGHTING.
Source record 10169354 at NHTSANHTSA communication ID: 10168964
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10168964 at NHTSANHTSA communication ID: 10168960
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Source components: SERVICE BRAKES, AIR:ANTILOCK · WHEELS.
Source record 10168960 at NHTSANHTSA communication ID: 10168958
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168958 at NHTSANHTSA communication ID: 10168956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
Source components: ELECTRICAL SYSTEM.
Source record 10168956 at NHTSANHTSA communication ID: 10168206
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
Source components: SUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY.
Source record 10168206 at NHTSANHTSA communication ID: 10168210
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures.
Source components: EQUIPMENT.
Source record 10168210 at NHTSANHTSA communication ID: 10168212
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
Source components: POWER TRAIN.
Source record 10168212 at NHTSANHTSA communication ID: 10168181
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the radio for vehicles with the condition of Intermittent Pop Noise from the Speakers Followed by a Reset of the Radio and Clock due to a software issue.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL.
Source record 10168181 at NHTSANHTSA communication ID: 10167466
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
Source components: ELECTRICAL SYSTEM.
Source record 10167466 at NHTSANHTSA communication ID: 10167465
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates if the sunroof, rear sliding window, and/or wireless charging are found to be inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.
Source components: ELECTRICAL SYSTEM · VISIBILITY.
Source record 10167465 at NHTSANHTSA communication ID: 10167462
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
Source components: ELECTRICAL SYSTEM.
Source record 10167462 at NHTSANHTSA communication ID: 10167460
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
Source components: LANE DEPARTURE.
Source record 10167460 at NHTSANHTSA communication ID: 10167458
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10167458 at NHTSANHTSA communication ID: 10167455
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
Source components: EQUIPMENT.
Source record 10167455 at NHTSANHTSA communication ID: 10168197
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how to identify possible DEF contamination.
Source components: FUEL SYSTEM, DIESEL.
Source record 10168197 at NHTSANHTSA communication ID: 10167448
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicle may have an ?Exhaust Fluid Quality Poor? on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
Source components: ENGINE AND ENGINE COOLING.
Source record 10167448 at NHTSANHTSA communication ID: 10168207
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168207 at NHTSANHTSA communication ID: 10167439
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.
Source components: ELECTRICAL SYSTEM.
Source record 10167439 at NHTSANHTSA communication ID: 10168209
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10168209 at NHTSANHTSA communication ID: 10168175
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: POWER TRAIN.
Source record 10168175 at NHTSANHTSA communication ID: 10167437
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Source components: ENGINE.
Source record 10167437 at NHTSANHTSA communication ID: 10167435
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates information on a hydrauilc rush type noise from the power steering gear. This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. The noise is most noticeable in the cab at idle, in park, with all accessories turned off.
Source components: STEERING.
Source record 10167435 at NHTSANHTSA communication ID: 10168185
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10168185 at NHTSANHTSA communication ID: 10167479
NHTSA source summary · Original PDF not reviewed by Recallfolio
N182202780 01 - Special Coverage. Certain Vehicles may have a condition where customers may experience increased brake pedal effort, hardbrake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applyingthe brakes. The engine mounted mechanical vacuum pump outputmay decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervalscould contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs,the hydraulic brake system remains functional but may require additionalpedal force. Please be aware that even if the vehicle exhibits this condition, it meets all federal motor vehicle safety standards forbrake performance. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.
Source components: ENGINE AND ENGINE COOLING · SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE.
Source record 10167479 at NHTSANHTSA communication ID: 10167434
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
Source components: ELECTRICAL SYSTEM.
Source record 10167434 at NHTSANHTSA communication ID: 10168208
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on key code security and information on GM key code look up applications.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168208 at NHTSANHTSA communication ID: 10168205
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168205 at NHTSANHTSA communication ID: 10168215
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information on a scraping noise heard from under the vehicle while driving.
Source components: EQUIPMENT.
Source record 10168215 at NHTSANHTSA communication ID: 10168214
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to reprogram more than 8 keys for the PPV.
Source components: UNKNOWN OR OTHER.
Source record 10168214 at NHTSANHTSA communication ID: 10168176
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed.
Source components: POWER TRAIN.
Source record 10168176 at NHTSANHTSA communication ID: 10167426
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.
Source components: ELECTRICAL SYSTEM.
Source record 10167426 at NHTSANHTSA communication ID: 10168204
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168204 at NHTSANHTSA communication ID: 10168188
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168188 at NHTSANHTSA communication ID: 10166665
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational Bulletin provides information on availability of Diesel Fuel additives.
Source components: FUEL SYSTEM, DIESEL.
Source record 10166665 at NHTSANHTSA communication ID: 10165914
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165914 at NHTSANHTSA communication ID: 10165905
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
Source components: STRUCTURE.
Source record 10165905 at NHTSANHTSA communication ID: 10165904
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
Source components: ELECTRICAL SYSTEM.
Source record 10165904 at NHTSANHTSA communication ID: 10165899
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technician that if they are unable to perform the solenoid characterization using the transmission unit number (TUN) off a replacement 8L90 RPO M5U automatic transmission to refer to the TUNs listed in this PI. If the TUN off the replacement transmission is listed they should refer to bulletin 18-NA-355 and perform a transmission fluid exchange due to possible fluid contamination. The dealer technician is to call technical assistance after the fluid exchange to get the TUN unlocked so they will then be able to complete solenoid valve characterization procedure.
Source components: POWER TRAIN.
Source record 10165899 at NHTSANHTSA communication ID: 10166659
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
Source components: ENGINE AND ENGINE COOLING.
Source record 10166659 at NHTSANHTSA communication ID: 10166638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
Source components: EQUIPMENT.
Source record 10166638 at NHTSANHTSA communication ID: 10166635
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides information to the tech to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away.
Source components: ENGINE AND ENGINE COOLING.
Source record 10166635 at NHTSANHTSA communication ID: 10166640
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in Drive concern.
Source components: ENGINE AND ENGINE COOLING.
Source record 10166640 at NHTSANHTSA communication ID: 10165877
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
Source components: ELECTRICAL SYSTEM.
Source record 10165877 at NHTSANHTSA communication ID: 10165874
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10165874 at NHTSANHTSA communication ID: 10165125
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Wheel Balancer Mounting Instructions.
Source components: WHEELS.
Source record 10165125 at NHTSANHTSA communication ID: 10165077
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical Bulletin provides procedures to upgrade a vehicle with the Android Auto feature for 2016 and 2017 Model Year vehicles.
Source components: ELECTRICAL SYSTEM.
Source record 10165077 at NHTSANHTSA communication ID: 10165080
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
Source record 10165080 at NHTSANHTSA communication ID: 10165127
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
Source components: ELECTRICAL SYSTEM.
Source record 10165127 at NHTSANHTSA communication ID: 10165087
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
Source components: EQUIPMENT.
Source record 10165087 at NHTSANHTSA communication ID: 10165124
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165124 at NHTSANHTSA communication ID: 10165078
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to clean and repair the complete fuel system due to dirt getting into the fuel system causing the vehicle to have a hard or no start.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10165078 at NHTSANHTSA communication ID: 10165126
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.
Source components: EQUIPMENT.
Source record 10165126 at NHTSANHTSA communication ID: 10165121
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165121 at NHTSANHTSA communication ID: 10165122
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165122 at NHTSANHTSA communication ID: 10165123
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10165123 at NHTSANHTSA communication ID: 10165104
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal.
Source components: POWER TRAIN.
Source record 10165104 at NHTSANHTSA communication ID: 10164754
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information explains that there are differences between the Elevated Idle, PTO and High Idle options.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10164754 at NHTSANHTSA communication ID: 10165090
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to check and repair the rear shackle and/or add lube to the leaf springs to correct the noise.
Source components: SUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY.
Source record 10165090 at NHTSANHTSA communication ID: 10165079
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
Source components: STEERING.
Source record 10165079 at NHTSANHTSA communication ID: 10163690
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates AFM / DFM usage Information. providing additional information on the AFM and DFM systems
Source components: EQUIPMENT:ELECTRICAL.
Source record 10163690 at NHTSANHTSA communication ID: 10163686
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
Source components: EQUIPMENT.
Source record 10163686 at NHTSANHTSA communication ID: 10163900
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
Source components: EQUIPMENT.
Source record 10163900 at NHTSANHTSA communication ID: 10163854
NHTSA source summary · Original PDF not reviewed by Recallfolio
N182198000 - Special Coverage Adjustment - Certain vehicles, equipped with a 5.3L or 6.2L engine, may have a condition which affects fuel injector function. Under certain circumstances one or more of the vehicle?s fuel injectors may deliver an improper amount of fuel to the engine. If this occurs, the Malfunction Indicator Lamp (Check Engine Light) will illuminate, the engine may idle or run rough, and the vehicle may stall. A diagnostic trouble code related to the fuel injector may be set. This special coverage only applies to vehicles in these states: California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont, and Washington. Dealers are to replace the fuel injectors as necessary. The repairs will be made at no charge to the customer.
Source components: ENGINE · FUEL SYSTEM, GASOLINE.
Source record 10163854 at NHTSANHTSA communication ID: 10164120
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information for new transmission oil to use, a procedure for exchanging the old fluid and adding the new fluid to a service transmission.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
Source record 10164120 at NHTSANHTSA communication ID: 10163908
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information for vehicles that has had the fuel injection pump replaced and is still within warranty.
Source components: ENGINE AND ENGINE COOLING.
Source record 10163908 at NHTSANHTSA communication ID: 10165334
NHTSA source summary · Original PDF not reviewed by Recallfolio
This SKU is a Tire Hoist Assembly. The customer communication requested return of unsold inventory to inspect for the shape of the centerpiece of the tire hoist being round when it should be square. If the centerpiece is the incorrect shape then the tire hoist cannot be operated with the OE tools, and the end user would therefore not be able to lower the spare tire with the vehicles original tools.
Source components: EQUIPMENT.
Source record 10165334 at NHTSANHTSA communication ID: 10163902
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.
Source components: POWER TRAIN.
Source record 10163902 at NHTSANHTSA communication ID: 10163665
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
Source components: VEHICLE SPEED CONTROL · WHEELS.
Source record 10163665 at NHTSANHTSA communication ID: 10163659
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
Source components: EQUIPMENT.
Source record 10163659 at NHTSANHTSA communication ID: 10163657
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
Source components: LANE DEPARTURE.
Source record 10163657 at NHTSANHTSA communication ID: 10163217
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides Information on Using Voice Pass-Thru to Access Voice Recognition Commands on Cell Phone and how it does not work on models equipped with IOA and IOB radios.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
Source record 10163217 at NHTSANHTSA communication ID: 10163193
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
Source components: EQUIPMENT.
Source record 10163193 at NHTSANHTSA communication ID: 10163226
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides information to correct a customer concern of a siren or whine noise from the in-tank fuel pump at temperatures below -6C or 20F, accompanied by start and stall, no start, loss of power and MIL illuminated. Technicians may find DTCs P0087, P018B, P228A, P228B or P2635 set in ECM.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10163226 at NHTSANHTSA communication ID: 10162149
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES.
Source record 10162149 at NHTSANHTSA communication ID: 10162143
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
Source components: ENGINE AND ENGINE COOLING.
Source record 10162143 at NHTSANHTSA communication ID: 10162136
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a vehicle setting both a P2635 and P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range. Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2. Navigate to fuel system depressurize and at engine idle depressurize the fuel system. The fuel pressure sensor value should drop to 0 and the engine will stall. If a sensor is causing this concern the suspected sensor will not drop to 0 the engine will stall however the sensor will still read 30 to 40 pounds per square inch.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10162136 at NHTSANHTSA communication ID: 10162127
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.
Source components: SUSPENSION.
Source record 10162127 at NHTSANHTSA communication ID: 10162124
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
Source components: ELECTRICAL SYSTEM.
Source record 10162124 at NHTSANHTSA communication ID: 10163213
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides the technician with information on how to perform a oil consumption test and a procedure to replace the pistons if found the cause of the oil consumption.
Source components: ENGINE.
Source record 10163213 at NHTSANHTSA communication ID: 10163245
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians and customers on possible carpet color mismatch.
Source components: EQUIPMENT.
Source record 10163245 at NHTSANHTSA communication ID: 10163237
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
Source record 10163237 at NHTSANHTSA communication ID: 10163215
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: POWER TRAIN.
Source record 10163215 at NHTSANHTSA communication ID: 10162108
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
Source components: POWER TRAIN.
Source record 10162108 at NHTSANHTSA communication ID: 10162106
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
Source components: ELECTRICAL SYSTEM.
Source record 10162106 at NHTSANHTSA communication ID: 10161969
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures.
Source components: EQUIPMENT · STRUCTURE.
Source record 10161969 at NHTSANHTSA communication ID: 10161926
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of pulsing, grinding, scraping noise from brakes, uneven front brake pad wear.
Source components: SERVICE BRAKES.
Source record 10161926 at NHTSANHTSA communication ID: 10161903
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of pulsing, grinding, scraping noise from brakes, uneven front brake pad wear.
Source components: SERVICE BRAKES.
Source record 10161903 at NHTSANHTSA communication ID: 10161887
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides the technician with information on how to perform a oil consumption test and a procedure to replace the pistons if found the cause of the oil consumption.
Source components: ENGINE.
Source record 10161887 at NHTSANHTSA communication ID: 10161978
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information for vehicles that has had the fuel injection pump replaced and is still within warranty.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10161978 at NHTSANHTSA communication ID: 10161932
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10161932 at NHTSANHTSA communication ID: 10161881
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
Source components: POWER TRAIN.
Source record 10161881 at NHTSANHTSA communication ID: 10161968
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
Source components: POWER TRAIN.
Source record 10161968 at NHTSANHTSA communication ID: 10161977
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information for vehicles that has had the fuel injection pump replaced and is still within warranty.
Source components: FUEL SYSTEM, GASOLINE · FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP.
Source record 10161977 at NHTSANHTSA communication ID: 10161011
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to technicians that the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10161011 at NHTSANHTSA communication ID: 10161005
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have either the truck or the snowplow's headlights are flickering or inoperative. There may be a diagnostic trouble code B2575 and or a B2699 set in the body control module. Technician will need to contact the snowplow manufacturer for additional information on their headlight changeover system. Technician is to refer to the latest version of the General Motors up-fitter integration bulletin 116 for additional information these circuits. Technician can find this information at http://www.gmupfitter.com/, under the "Technical Bulletin" Tab and then "Show all bulletins."
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10161005 at NHTSA