The manufacturer’s record · Page 14 of 18
Original record summaries, dates and identifiers for this model-year. Records 1,301–1,400 of 1,780, ordered newest first. Dated records on this page: Nov 2, 2016–Feb 13, 2017.
Back to 2016 Chevrolet SILVERADO 2500 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10113417
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicationends thewireless charging module restriction through the General Motors Technical Assistance Center.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10113417 at NHTSANHTSA communication ID: 10113416
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
Source components: EQUIPMENT.
Source record 10113416 at NHTSANHTSA communication ID: 10113415
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
Source components: SUSPENSION:FRONT.
Source record 10113415 at NHTSANHTSA communication ID: 10113413
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10113413 at NHTSANHTSA communication ID: 10113407
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · SEATS:FRONT ASSEMBLY:RECLINER.
Source record 10113407 at NHTSANHTSA communication ID: 10116596
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
Source components: STEERING.
Source record 10116596 at NHTSANHTSA communication ID: 10116645
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information is requesting information from the field on vehicles that have the condition of Check Engine Light, Delayed Shifts and/or Transmission Stuck in Gear with DTC P0751, P0752, P0756, P0757, P0761 or P0762 Set.
Source components: ENGINE.
Source record 10116645 at NHTSANHTSA communication ID: 10113393
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesContent Theft Deterrent RPO UTJ is included and only available with Remote Vehicle Start RPO BTV. If the vehicle is not equipped with Remote Vehicle Start RPO BTV the vehicle will not have Content Theft Deterrent.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10113393 at NHTSANHTSA communication ID: 10116572
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of Rear Camera Gridlines, Service Rear Vision System Message, Radio Turns On Unwanted At Startup, and/or Navigation Radio Destination State Defaults To WV, Intermittent Radio/display Resets, Volume Control Inoperative.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10116572 at NHTSANHTSA communication ID: 10116571
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to turn the audible feedback option on and off in the radio settings to prevent an audible beep will occur when scrolling from page 1 to page 2 of the OnStar menu, which may be interpreted as a hands free OnStar call request.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10116571 at NHTSANHTSA communication ID: 10130559
NHTSA source summary · Original PDF not reviewed by Recallfolio
17018-Customer Satisfaction Program. Certain vehicles, equipped with power front passenger seat adjuster that was previously replaced, may have a condition in which the front passenger seat can be adjusted to a position beyond the occupant design travel range. Dealers will inspect front passenger seat tracks and, as necessary, install the seat stop(s).
Source components: SEATS:FRONT ASSEMBLY:POWER ADJUST.
Source record 10130559 at NHTSANHTSA communication ID: 10116540
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10116540 at NHTSANHTSA communication ID: 10116539
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10116539 at NHTSANHTSA communication ID: 10116547
NHTSA source summary · Original PDF not reviewed by Recallfolio
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10116547 at NHTSANHTSA communication ID: 10116551
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the ECM to correct multiple transmission concerns.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10116551 at NHTSANHTSA communication ID: 10116550
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the ECM and TCM to correct multiple transmissions concerns.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10116550 at NHTSANHTSA communication ID: 10116537
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)
Source components: TIRES.
Source record 10116537 at NHTSANHTSA communication ID: 10116538
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10116538 at NHTSANHTSA communication ID: 10116534
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10116534 at NHTSANHTSA communication ID: 10113328
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10113328 at NHTSANHTSA communication ID: 10113321
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10113321 at NHTSANHTSA communication ID: 10116574
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10116574 at NHTSANHTSA communication ID: 10113318
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10113318 at NHTSANHTSA communication ID: 10113310
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10113310 at NHTSANHTSA communication ID: 10113309
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL · ELECTRICAL SYSTEM:WIRING.
Source record 10113309 at NHTSANHTSA communication ID: 10113298
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with an intermittent loss of gridlines in the rear camera display screen and a "Service Rear Vision System" message that both happen at the same time. Technician should check for Diagnostic Trouble Codes and follow published Service Information diagnostics for the Diagnostic Trouble Codes. If not Diagnostic Trouble Codes stored and the concern was duplicated or the customer described the concern, dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10113298 at NHTSANHTSA communication ID: 10113297
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10113297 at NHTSANHTSA communication ID: 10116536
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
Source components: ELECTRICAL SYSTEM.
Source record 10116536 at NHTSANHTSA communication ID: 10113295
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10113295 at NHTSANHTSA communication ID: 10130547
NHTSA source summary · Original PDF not reviewed by Recallfolio
28770 - SUB A ?Service 4WD? message may be displayed on the Driver Information Center and DTC C0398 may be set. Concurrently, the vehicle is permanently locked in 4HI and cannot be shifted shift out of it while the code is present. If the code is cleared, this scenario may repeat if the transfer case is in ?Auto? mode and driven for approx. 2 or more hours. Customers will likely notice that the steering wheel is harder to turn, the engine will feel like it has lost power and the tires may squeal when turning in a parking lot. Dealers are to reprogram the transfer case.
Source components: ELECTRICAL SYSTEM.
Source record 10130547 at NHTSANHTSA communication ID: 10113291
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10113291 at NHTSANHTSA communication ID: 10113290
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have either the truck or the snowplow's headlights are flickering or inoperative. There may be a diagnostic trouble code B2575 and or a B2699 set in the body control module. Technician will need to contact the snowplow manufacturer for additional information on their headlight changeover system. Technician is to refer to the latest version of the General Motors up-fitter integration bulletin 116 for additional information these circuits. Technician can find this information at http://www.gmupfitter.com/, under the "Technical Bulletin" Tab and then "Show all bulletins."
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10113290 at NHTSANHTSA communication ID: 10113289
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10113289 at NHTSANHTSA communication ID: 10113288
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on installing Regular Production Option Code 9L7 Up-fitter Auxiliary Switches. Technician will need to reference the latest version of General Motors Up-fitter Integration Bulletin 110. The information can be found at http://www.gmupfitter.com/ under the "Technical Bulletin" Tab and then "Show all bulletins."
Source components: EQUIPMENT:ELECTRICAL.
Source record 10113288 at NHTSANHTSA communication ID: 10111737
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE.
Source record 10111737 at NHTSANHTSA communication ID: 10111736
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a rough idle and/or momentary lack of power after cold starting the engine and immediately placing the transmission in gear. Technician should follow published Service Information diagnostics first. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: ENGINE · POWER TRAIN.
Source record 10111736 at NHTSANHTSA communication ID: 10111734
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10111734 at NHTSANHTSA communication ID: 10111732
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
Source record 10111732 at NHTSANHTSA communication ID: 10111751
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10111751 at NHTSANHTSA communication ID: 10111746
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared Message Displayed on DIC, DTC P2463 May Be Set.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111746 at NHTSANHTSA communication ID: 10111729
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
Source components: ENGINE.
Source record 10111729 at NHTSANHTSA communication ID: 10111744
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111744 at NHTSANHTSA communication ID: 10111726
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Allison LCT1000 Transmission is no longer on restriction through the General Motors Product Quality Center. Dealer can now order part through the normal Customer Care and Aftersales parts process.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10111726 at NHTSANHTSA communication ID: 10111779
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111779 at NHTSANHTSA communication ID: 10111723
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
Source components: BACK OVER PREVENTION · LANE DEPARTURE.
Source record 10111723 at NHTSANHTSA communication ID: 10111722
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
Source components: STRUCTURE · SUSPENSION · WHEELS.
Source record 10111722 at NHTSANHTSA communication ID: 10111716
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded
Source components: ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · LANE DEPARTURE · STEERING.
Source record 10111716 at NHTSANHTSA communication ID: 10111715
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
Source components: ELECTRICAL SYSTEM.
Source record 10111715 at NHTSANHTSA communication ID: 10111714
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10111714 at NHTSANHTSA communication ID: 10111711
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have installed an aftermarket bed cap or topper may question where they can wire in the center high mounted stop light for the cap or topper. Provisions for the center high mounted stop light have been provided at the Rear Body Junction Block (X63A) connector X6 terminal 1 for 2014-2015 model years. For vehicle model years 2016-2017 provisions for the center high mounted stop light have been provided at connector X400 terminal 4, circuit 1054.
Source components: EQUIPMENT.
Source record 10111711 at NHTSANHTSA communication ID: 10111709
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
Source components: ELECTRICAL SYSTEM:WIRING · ENGINE.
Source record 10111709 at NHTSANHTSA communication ID: 10111708
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles that may have fuel gauge that shows empty and the low fuel level indicator is on. Technician will find Diagnostic Trouble Code P2636 will be set in the Engine Control Module. Technician will need to install (Y) Fuel Tank Fill Vent hose. Technician will need to remove the original fuel balance pump line from the pump tube. Technician can now add a new line from the (Y) to the fuel balance pump line.
Source components: ENGINE.
Source record 10111708 at NHTSANHTSA communication ID: 10111705
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on vehicles that may have an intermittent high idle. If a technician has duplicated, or the customer description aligns with the speeds mentioned in the idle speed description tables, the idle speed should be considered a normal characteristic of current vehicle design.
Source components: STEERING:LINKAGES:ARM:IDLER AND ATTACHMENT.
Source record 10111705 at NHTSANHTSA communication ID: 10111743
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
Source components: SUSPENSION:FRONT:SHOCK ABSORBER.
Source record 10111743 at NHTSANHTSA communication ID: 10111740
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111740 at NHTSANHTSA communication ID: 10111741
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111741 at NHTSANHTSA communication ID: 10111758
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on how to test and perform a clutch learn procedure to correct delayed clutch engagement.
Source components: POWER TRAIN:CLUTCH ASSEMBLY.
Source record 10111758 at NHTSANHTSA communication ID: 10111742
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111742 at NHTSANHTSA communication ID: 10111696
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to help converting vehicles to fleet key option Regular Production Option Code 6E2 or 6E8. Technician will need to check the Regular Production Option Code for 6E2 or 6E8. Technician will need to order the correct key part number per the Regular Production Option Code. Then the technician will need re-code the lock cylinders to match the Regular Production Option Code. Also replace the Body Control Module and normal Service Programming System to the Body Control Module will turn the vehicle to a common key.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111696 at NHTSANHTSA communication ID: 10111694
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Upfitters questions about installing aftermarket electrical accessories. Dealer should reference the latest version of General Motors Upfitter Integration Bulletin 115 for this information. It can be found at http://www.gmupfitter.com.
Source components: ELECTRICAL SYSTEM.
Source record 10111694 at NHTSANHTSA communication ID: 10111693
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of the snow plow headlamps inoperative after switching from the factory headlamps to the snowplow headlamps. There may be a diagnostic trouble code B2575 and or a B2699 set in the body control module. Technician is to refer to the latest version of the General Motors up-fitter integration bulletin 116 for additional information these circuits.
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10111693 at NHTSANHTSA communication ID: 10138009
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin ends the need for information from the field on vehicles that have the condition of the Air bag light illuminated and SIR codes set within the SIR module.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138009 at NHTSANHTSA communication ID: 10114858
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory 22" 6-Spoke Split Chrome Wheels Regular Production Option Code (SEU) or during any service requiring wheel removal.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10114858 at NHTSANHTSA communication ID: 10114857
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a poor Heater-Vent-Air Conditioning air flow from the passenger side far right dash vent when compared to the other dash vents. Technician will need to remove the Heater-Vent-Air Conditioning air distributor duct. Technician can now cut out the portion of the deflector to increase air flow.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10114857 at NHTSANHTSA communication ID: 10114855
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about owners that want the auto door lock disabled. There is no avalible setting or Body Control Module calibration to turn off the auto door locks.
Source components: LATCHES/LOCKS/LINKAGES:DOORS:LATCH.
Source record 10114855 at NHTSANHTSA communication ID: 10114854
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
Source components: ELECTRICAL SYSTEM.
Source record 10114854 at NHTSANHTSA communication ID: 10114853
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates New model features of the 2016 and 2017 Silverado and Sierra eAssist.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10114853 at NHTSANHTSA communication ID: 10114852
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and re-pair any phones that were deleted.
Source components: ELECTRICAL SYSTEM.
Source record 10114852 at NHTSANHTSA communication ID: 10114851
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10114851 at NHTSANHTSA communication ID: 10114850
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
Source components: ELECTRICAL SYSTEM · ELECTRONIC STABILITY CONTROL (ESC) · STEERING · TIRES · VISIBILITY.
Source record 10114850 at NHTSANHTSA communication ID: 10137996
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the FVCM if the battery has issues that are related to the front camera module.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT · FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA.
Source record 10137996 at NHTSANHTSA communication ID: 10137956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 48 and 104 KM/H (30 and 65 MPH) at a steady state.
Source components: EQUIPMENT · POWER TRAIN.
Source record 10137956 at NHTSANHTSA communication ID: 10138006
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information bulletin is ending the need for information on vehicles with the condition of Vehicle Crank with No Start or Stalling with DTC P0011 and/or P00C6 Set.
Source components: EQUIPMENT.
Source record 10138006 at NHTSANHTSA communication ID: 10114848
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
Source components: EQUIPMENT:ELECTRICAL.
Source record 10114848 at NHTSANHTSA communication ID: 10138001
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to repair information to correct a customer concern of the hood fluttering, vibrating or displaying visible motion at highway speeds or over rough road surfaces.
Source components: STRUCTURE:BODY:HOOD.
Source record 10138001 at NHTSANHTSA communication ID: 10114842
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10114842 at NHTSANHTSA communication ID: 10114840
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate
Source components: ELECTRICAL SYSTEM · SEATS.
Source record 10114840 at NHTSANHTSA communication ID: 10114839
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Trailer connection not recognized or ?Check Trailer wiring? or ?Service Trailer Brake? message. Technician may find Diagnostic Trouble Codes C1112, C1113, C1114, C111B, U1556, and/or U1505. Technician will need to inspect the Trailer Brake Power Module connector for corroded terminals and replace as necessary.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL.
Source record 10114839 at NHTSANHTSA communication ID: 10137951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delayed Engagement After Sitting With Engine Off - Torque Converter Fluid Drain Back
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT.
Source record 10137951 at NHTSANHTSA communication ID: 10137990
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding formulation of a lighter variant paint being made available in order to match the paint on trucks exhibiting a lighter color due to mis-application at the plant.
Source components: EQUIPMENT · STRUCTURE:BODY.
Source record 10137990 at NHTSANHTSA communication ID: 10137617
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on higher then expected oil consumption.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10137617 at NHTSANHTSA communication ID: 10114835
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.
Source components: POWER TRAIN · SERVICE BRAKES · VEHICLE SPEED CONTROL:LINKAGES.
Source record 10114835 at NHTSANHTSA communication ID: 10114834
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnosis and repair steering that feels loose or has excessive play. This concern could be caused by the Pitman Shaft Over-Center Preload Adjustment becoming misadjusted. Technician will need to replace the steering gear pitman arm shaft with an updated design.
Source components: STEERING · STEERING:GEAR BOX:SHAFT PITMAN.
Source record 10114834 at NHTSANHTSA communication ID: 10114831
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
Source components: ENGINE · EQUIPMENT ADAPTIVE/MOBILITY · FUEL SYSTEM, GASOLINE.
Source record 10114831 at NHTSANHTSA communication ID: 10114830
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have harsh concerns. Technician are advised to use GDS2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
Source record 10114830 at NHTSANHTSA communication ID: 10114829
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10114829 at NHTSANHTSA communication ID: 10138013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a MIL or a engine misfire due to a loose spark plug wire.
Source components: ENGINE AND ENGINE COOLING.
Source record 10138013 at NHTSANHTSA communication ID: 10137624
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.
Source components: EQUIPMENT.
Source record 10137624 at NHTSANHTSA communication ID: 10137953
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical Bulletin provides a fix to reprogram the radio for vehicles that may experience any of the following conditions: DTC U0184 Set, Radio Inoperative, Blue Screen, AM Clipping Noise, HD On/Off Status Not Retained in Stations, Time Lag on Transitions, No Audio with Internal Amp, Park Assist Symbol Position Wrong in Rear View Camera
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10137953 at NHTSANHTSA communication ID: 10137622
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
Source components: STRUCTURE:BODY:DOOR · VISIBILITY:GLASS, SIDE/REAR.
Source record 10137622 at NHTSANHTSA communication ID: 10137616
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · TIRES.
Source record 10137616 at NHTSANHTSA communication ID: 10114825
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have harsh shifts concerns. Technicians will use Global Diagnostic System 2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found in the pan, technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
Source components: POWER TRAIN.
Source record 10114825 at NHTSANHTSA communication ID: 10138008
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of the rear view camera is inoperative.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138008 at NHTSANHTSA communication ID: 10137625
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
Source components: ELECTRICAL SYSTEM.
Source record 10137625 at NHTSANHTSA communication ID: 10137615
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · TIRES.
Source record 10137615 at NHTSANHTSA communication ID: 10114824
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: ELECTRICAL SYSTEM.
Source record 10114824 at NHTSANHTSA communication ID: 10137621
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
Source components: EQUIPMENT · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS.
Source record 10137621 at NHTSANHTSA communication ID: 10137620
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
Source components: EQUIPMENT.
Source record 10137620 at NHTSANHTSA communication ID: 10137619
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational Bulletin provides information on availability of Diesel Fuel additives.
Source components: EQUIPMENT · FUEL SYSTEM, DIESEL.
Source record 10137619 at NHTSANHTSA communication ID: 10137618
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational Bulletin provides information on available Diesel Fuel Additives.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · FUEL SYSTEM, DIESEL.
Source record 10137618 at NHTSA