2017 Chevrolet SILVERADO 1500 Manufacturer communications & TSBs.Page 11
Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 1,285, ordered newest first. Dated records on this page: Dec 11, 2017–Feb 1, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 1, 2019Service Bulletin/Repair Instructions
PIT5546D
NHTSA communication ID: 10154263
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that water leaking into the headlamp assembly or headlamp assembly connections can cause an electrical short which will keep modules from shutting down causing a dead battery and a no crank condition, a crank no start, or unable to program the engine control module. Engine control module will set a diagnostic trouble code of P1682, or the engine will continue to run with the ignition off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information to check the shutters through the grille opening of the vehicle. If snow and/or ice is present on the active grille air shutters, take pictures and submit through the Field Reporting Process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information and document the exact location of the wire chafing by taking a photo of the flex fuel pigtail as it appears BEFORE repairs are made.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides additional guidance for diagnosing vibrations or disturbances that may occur on full size pickups and how to correct and repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of hearing a pickup box ornamentation bar (Sports Bar) wind noise or rattle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers footwell area when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or click type noise while driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Upfitters questions about installing aftermarket electrical accessories. Dealer should reference the latest version of General Motors Upfitter Integration Bulletin 115 for this information. It can be found at http://www.gmupfitter.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the GEN I charging system with a GEN II charging system only if vehicles apply within the settings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to dealer technicians to refer to service update bulletin N182179090 for 2018 model vehicles and to use labor operation 4029959 Emissions - Customer Concern Not Duplicated (CCND) for 2017 model year vehicles with DTC P140B setting.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to dealer technicians to refer to service update bulletin N182179090 for 2018 model vehicles and to use labor operation 4029959 Emissions - Customer Concern Not Duplicated (CCND) for 2017 model year vehicles with DTC P140B setting.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner's Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of additional information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a whistle noise in the vehicle from the driver or passenger side. Technician will need to inspect for voids in the body sealer on the left or right side A-pillar. Technician should also inspect for voids in the body sealer at the cowl seam and apply sealer as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer an issue where the vehicle's service engine soon light may illuminate due to trouble codes P0601-P0604, P0606, P062B, P062F, P0630, P16F3, or P262B . The dealer is to inspect the engine control module's electrical connections and for proper powers and grounds. Dealer instructed to replace the Engine Control Module, if no other issues found.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesSES lamp, setting DTC P0333 when shifting the Transmissionfrom park.DTC P0333 cansetdue to voltage from the Transmission park/neutral signal 1circuit bleeding into the knock sensor system circuits.If SI does not isolate the concern inspect the K20 ECM connector X2 looking for debris, connectorand or terminal concerns.
Source components: POWER TRAIN · POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have issues were the customer will need increased effort to depress the brake pedal. Technician may find fluid in the brake booster and/or the booster vacuum line. Technician will need to replace Vacuum Pump, Brake Booster, Master Cylinder, Vacuum Pump Belt and the Vacuum Line between the booster and the pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (LV3), 5.3L (L83), 6.2L (L86) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates. A vehicle may have a concern ofDTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers foot well area when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates information to have dealers contact TCSC for programming assistance with new amplifier part numbers until all the new amplifier numbers are setup correctly for programming.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: ELECTRICAL SYSTEM · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the Generator Control Module (GCM). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a power steering control module calibration error that does not allow its DTC's to transition to history and they always stay current, which can mislead a technician diagnosis. Dealers are to reprogram the power steering control module with updated calibration which will allow DTC's to transition to history if the issue that caused the DTC(s) are now longer present.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (L83), 5.3L (L86), 6.2L (LV3) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: BACK OVER PREVENTION: WARNINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the drivers front door window regulator motor and door wiring harness if water and/or corrosion is found in the connectors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesP0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to Add 1 quart of coolant to the upper chamber of the surge tank in order to bring the level up to the bottom of the fill neck to correct a condition of the coolant surge tank appears low and/or a low coolant message displayed intermittently due to the fill process at the plant cannot purge all of the air from the cooling system and surge tank.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that water leaking into the headlamp assembly or headlamp assembly connections can cause an electrical short which will keep modules from shutting down causing a dead battery and a no crank condition, a crank no start,or unable to program the engine control module. Engine control module will set a diagnostic trouble code of P1682, or the engine will continue to run with the ignition off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
Source components: STRUCTURE:BODY:HOOD · STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Trailer connection not recognized or “Check Trailer wiring” or “Service Trailer Brake” message. Technician may find Diagnostic Trouble Codes C1112, C1113, C1114, C111B, U1556, and/or U1505. Technician will need to inspect the battery and Trailer Brake Power Module connector for corroded terminals and replace as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have installed an aftermarket bed cap or topper may question where they can wire in the center high mounted stop light for the cap or topper. Provisions for the center high mounted stop light have been provided at the Rear Body Junction Block (X63A) connector X6 terminal 1 for 2014-2015 model years. For vehicle model years 2016-2017 provisions for the center high mounted stop light have been provided at connector X400 terminal 4, circuit 1054.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a check engine light on. Technician may find Diagnostic Trouble Code P026A. The owner's manual advises not to drive above 45 MPH with a snowplow installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm.Abroken rocker arms that could result in the valve dropping to the cylinder, causing a catastrophic failure and the engine requires replacement due to cylinder head and block damage. If a broken rocker arm is found check to see if the valve dropped into the cylinder if so the engine will need to be replaced.On occasions the valve will not drop, reinstall any valve keepers and replace all the intake rocker arms.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the dealers on vehicles that have the condition of a malfunction indicator lamp illuminated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Malfunction Indicator Lamp Illuminated with DTCs P0335, P0340, or P0365 Set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.