2013 Chevrolet CRUZE Manufacturer communications & TSBs.Page 15
Original record summaries, dates and identifiers for this model-year. Records 1,401–1,500 of 1,882, ordered newest first. Dated records on this page: Oct 21, 2013–Feb 21, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 21, 2014Service Bulletin/Repair Instructions
09-03-10-016B
NHTSA communication ID: 10138638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to replace the starer and the fuse block to correct a customers concern of the starter or flywheel making a knocking noise.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:STARTER ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure to replace the starter and fuse block to correct the customer concern of a knocking noise on start up.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:STARTER ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure check for DTCs in relation to engine slow warm up cycle and is considered a normal condition..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with the service engine soon lamp that comes on. Technician may find Diagnostic Trouble Code U0101. Technician should review the appropriate Service Information diagnostics for DTC U0101. Also gather all other diagnostic trouble codes in the vehicle and which modules they are set in. The transmission connector pins should be checked for damaged terminals or poor terminal fit. Also inspect the under hood fuse block for damaged terminals or poor terminal fit and mis-positioned fuses in fuse block. Inspect the ground for the Transmission Control Module. Technician should refer to Service Information automatic transmission controls schematics to determine the ground identification.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have heated seats inoperative. Technician may find Diagnostic Trouble Code U0209 in the Heater-Vent-Air Conditioning. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME MAY COMPLAIN ABOUT REDUCED ENGINE POWER AND/OR A REDUCED ENGINE POWER MESSAGE BEING DISPLAYED ON THE DRIVER INFORMATION CENTER. ENGINEERS NEED TO GATHER THE VEHICLES' INFORMATION PRIOR TO ANY ATTEMPT TO MAKE REPAIRS IN ORDER TO DETERMINE THE CAUSE. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio can be turned on after turning the ignition off and opening the driver's door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Electronic Brake Control Module and the Brake Pressure Modulator Valve parts restriction has ended. Dealer can now order the parts directly through your Parts Department without General Motors Technical Assistance Center authorization.
Source components: SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE · SERVICE BRAKES, ELECTRIC · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DIFFERENTIAL PROPORTIONAL VALVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engineering Information Sunroof or Sunshade Inoperative, DTC U151B Set Condition Important: If the customer did not bring their vehicle in for this concern, DO NOT proceed with this EI. Some customers may comment that the sunroof or shade is inoperative when the sunroof switch is pressed. When checking the vehicle for DTCs, the BCM may report U151B current or in history. Cause GM Engineering is attempting to determine the root cause of the above condition. Engineering has a need to gather information on vehicles PRIOR to repair that may exhibit this condition. As a result, this information will be used to "root cause" the customer's concern and develop/validate a field fix.
Source components: ELECTRICAL SYSTEM · VISIBILITY:SUN/MOON ROOF ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bump, Surge or Vibration at Idle in Drive at a Stop Condition/Concern Some customers may comment on a bump feeling, a surge or an engine vibration while stopped at idle with the transmission in Drive and their foot on the service brake
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pulsating/Rotational Noise from Right Rear of Vehicle on Brake Apply Condition/Concern Some customers may comment about a pulsating/rotational noise coming from the right rear of the vehicle during brake apply. This noise may be caused by an interaction between the brake drum and brake shoe.
Source components: SERVICE BRAKES, AIR:DRUM:SHOES/LININGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the part restriction on the electric power steering module for NJ1 part numbers has ended. Dealer can order parts directly through your parts department.
Source components: EQUIPMENT:ELECTRICAL · STEERING:ELECTRIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides an update for PI0686 to update the Model years and update the Labor Operation to the Global Labor Code (GLC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET: POWER ADJUSTED SEAT OR 6 WAY MANUAL DRIVER AND/OR PASSENGER SEAT, THERE WOULD BE SHIFTING, SQUEAKING, CLUNKING OR CLICKING NOISE WHEN TURNING CORNER. *PE UPDATED 1/29/2014 *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with a diagnostic tip service steering message or service stability message. Technician may find a Diagnostic Trouble Code C056E Sym 42 and a Diagnostic Trouble Code C0569 Sym 3A setting after a new steering gear assembly was installed. If Diagnostic Trouble Code C0710 Sym 71 is set it must be addressed firth before performing a steering gear "set-up" in Service Programming System. Steering Angle Sensor module Diagnostic Trouble Code C056D Sym 00 and it must be address first. Technician should be advised that Diagnostic Trouble Codes DTC C056E Sym 42 or C0569 Sym 3A will set when a steering gear assembly was replaced without Service Programming System programming.
Source components: STEERING · STEERING:GEAR BOX (OTHER THAN RACK AND PINION).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a rattle or knock noise from the engine transmission area when starting the vehicle. Technician will need to verify that noise is not engine related by following "Engine Noise on Start-up, but only lasting a few seconds" diagnostic in Service Information. Technician should be advised that Engineering has identified that the starter motor is rotating the crankshaft at a speed that excites the dual mass flywheel springs and is the root cause of the noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary Informational bulletin provides information on Battery Test Cold Cranking Amperage (CCA) for Original Equipment Batteries and Testing Tips.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when attempting to start vehicle "No Fob Detected" message is displayed. Technician will find the Key FOB works and the vehicle will start with the key FOB is placed in the pocket. Technician will need to replace the Key FOB with the Key FOB with Passive Entry Passive Start.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have brake lights remain on with the vehicle off and parked and/or the vehicle battery goes dead. Technician will need to inspect for aftermarket parts.