The manufacturer’s record · Page 15 of 21
Original record summaries, dates and identifiers for this model-year. Records 1,401–1,500 of 2,039, ordered newest first. Dated records on this page: Dec 11, 2013–Apr 21, 2014.
Back to 2013 Chevrolet CAMARO problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10111815
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
Source components: ENGINE.
Source record 10111815 at NHTSANHTSA communication ID: 10111811
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10111811 at NHTSANHTSA communication ID: 10111810
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111810 at NHTSANHTSA communication ID: 10111806
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a flutter or buzz that occurs at 800-900 revolutions per minute with the vehicle in second or third gear. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
Source record 10111806 at NHTSANHTSA communication ID: 10135210
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides information to reset the phone and factory reset of the radio to correct the customers concern of the iphone connection concerns.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10135210 at NHTSANHTSA communication ID: 10111805
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE).
Source record 10111805 at NHTSANHTSA communication ID: 10135201
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10135201 at NHTSANHTSA communication ID: 10111796
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnosis and repair vehicles with a noise can be heard from the dash area while the engine is running. Technician will gain access to the heater core inlet hose and remove it. There will be an inlet screen installed in the core that may be plugged with debris, causing this noise. If debris is present clean the screen or replace it. The vehicles coolant system will need to be flushed if debris if found. If a lot of debris is found in the inlet screen, back flush the heater core as well. Do not replace the heater core for a noise issue.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS.
Source record 10111796 at NHTSANHTSA communication ID: 10111792
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111792 at NHTSANHTSA communication ID: 10250013
NHTSA source summary · Original PDF not reviewed by Recallfolio
High Voltage Safety ? High Voltage Disabling
Source components: ELECTRICAL SYSTEM.
Source record 10250013 at NHTSANHTSA communication ID: 10247684
NHTSA source summary · Original PDF not reviewed by Recallfolio
Navigation Radio, Radio, Amplifier, Human Machine Interface.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10247684 at NHTSANHTSA communication ID: 10245323
NHTSA source summary · Original PDF not reviewed by Recallfolio
Navigation Radio, Radio, Amplifier, Human Machine Interface.
Source components: EQUIPMENT:ELECTRICAL:INFOTAINMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10245323 at NHTSANHTSA communication ID: 10073728
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE.
Source record 10073728 at NHTSANHTSA communication ID: 10055840
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: SOME VEHICLES/TRUCKS MAY EXPERIENCE A NO CRANKING OR STARTING, CAUSED BY POSSIBLE EXCESSIVE LEAKAGE FROM CYLINDER PAST EXHAUST OR INTAKE VALVE, LOW STATIC COMPRESSION, SENSOR IS DISCONNECTED, OR WHILE CRANKING, VALVE TRAIN FAILS TO MOVE. MODEL 2009-2014 CORVETTE, CAMARO, EXPRESS, SS, SILVERADO, SUBURBAN, TAHOE, SAVANA, SIERRA, YUKON. *PE
Source components: ENGINE.
Source record 10055840 at NHTSANHTSA communication ID: 10055422
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: SOME DTC CODES MAY BE SET, P0016, P0017, P0018, P0019, P0008, OR P0009. 3.6 LY7 WITH CAM ACTUATOR DTC.THE RELUCTOR FOR THE CRANKSHAFT SENSOR PRESSED ON THE CRANKSHAFT MAY HAVE MOVED. ALSO INCLUDED BUICK ALLURE MODEL YEAR 2005. *JS
Source components: ENGINE.
Source record 10055422 at NHTSANHTSA communication ID: 10137887
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10137887 at NHTSANHTSA communication ID: 10111886
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111886 at NHTSANHTSA communication ID: 10137866
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
Source components: EQUIPMENT.
Source record 10137866 at NHTSANHTSA communication ID: 10111850
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111850 at NHTSANHTSA communication ID: 10111849
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10111849 at NHTSANHTSA communication ID: 10111848
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111848 at NHTSANHTSA communication ID: 10111846
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a customer?s request to install OnStar Bluetooth. Dealer should be advised at this time, there are no provisions to add this option to vehicles that were not built with it.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111846 at NHTSANHTSA communication ID: 10111845
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10111845 at NHTSANHTSA communication ID: 10247681
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information On Requests To Add OnStar Bluetooth Option.
Source components: EQUIPMENT.
Source record 10247681 at NHTSANHTSA communication ID: 10245950
NHTSA source summary · Original PDF not reviewed by Recallfolio
Canadian Customers Unable To Place Calls In The United States
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10245950 at NHTSANHTSA communication ID: 10073396
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10073396 at NHTSANHTSA communication ID: 10070998
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: EQUIPMENT.
Source record 10070998 at NHTSANHTSA communication ID: 10111966
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111966 at NHTSANHTSA communication ID: 10111964
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111964 at NHTSANHTSA communication ID: 10138646
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
Source record 10138646 at NHTSANHTSA communication ID: 10111956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: ENGINE.
Source record 10111956 at NHTSANHTSA communication ID: 10111955
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
Source record 10111955 at NHTSANHTSA communication ID: 10138640
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
Source record 10138640 at NHTSANHTSA communication ID: 10138639
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician the proper way to install and torque the wheel.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · WHEELS.
Source record 10138639 at NHTSANHTSA communication ID: 10138638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
Source components: WHEELS.
Source record 10138638 at NHTSANHTSA communication ID: 10138637
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES · WHEELS:RIM.
Source record 10138637 at NHTSANHTSA communication ID: 10111940
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to diagnose a concern of the blower motor speed display frozen on the radio display. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: ENGINE AND ENGINE COOLING.
Source record 10111940 at NHTSANHTSA communication ID: 10138631
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
Source components: TIRES · WHEELS:RIM.
Source record 10138631 at NHTSANHTSA communication ID: 10138630
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains the use of Nitrogen in GM tires.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES.
Source record 10138630 at NHTSANHTSA communication ID: 10138629
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and recommended practices.
Source components: TIRES.
Source record 10138629 at NHTSANHTSA communication ID: 10138623
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on part restriction and ordering of Onstar vehicle communication modules.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138623 at NHTSANHTSA communication ID: 10138621
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138621 at NHTSANHTSA communication ID: 10111927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, GASOLINE · SERVICE BRAKES, HYDRAULIC.
Source record 10111927 at NHTSANHTSA communication ID: 10111918
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111918 at NHTSANHTSA communication ID: 10111917
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with the steps on repairing a clunk noise after shifting from reverse to drive or drive to reverse and then accelerating. The concern is only with rear wheel drive 6L45 or 6L50 automatic transmissions with Regular Production Option Code MYA or MYB apply. Apply thread locker to the transmission output shaft flange splines and install a new front propeller shaft flange nut. Apply thread locker to the new propeller shaft flange nut if it does not contain a pre-applied adhesive patch.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION · WHEELS.
Source record 10111917 at NHTSANHTSA communication ID: 10138609
NHTSA source summary · Original PDF not reviewed by Recallfolio
The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138609 at NHTSANHTSA communication ID: 10138607
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information provides a procedure to reprogram the ECM to correct the customers concern of an engine misfire on acceleration.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE.
Source record 10138607 at NHTSANHTSA communication ID: 10138606
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a windshield.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · VISIBILITY:WINDSHIELD.
Source record 10138606 at NHTSANHTSA communication ID: 10138605
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10138605 at NHTSANHTSA communication ID: 10111916
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES · STEERING.
Source record 10111916 at NHTSANHTSA communication ID: 10111915
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 3.91 gear kit part number 22813040 the 2013-2014 Chevrolet Camaro equipped with Regular Production Option Code (1LE) placed on a parts restriction though General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
Source components: EQUIPMENT.
Source record 10111915 at NHTSANHTSA communication ID: 10138604
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides service information to the dealer technicians that the remote start will not work with the ONSTAR REMOTE Link applcation
Source components: ELECTRICAL SYSTEM.
Source record 10138604 at NHTSANHTSA communication ID: 10111909
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10111909 at NHTSANHTSA communication ID: 10138601
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to inspect the transmissions filter for splits or cracks to correct the customers concern for no forward, reverse or slips.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10138601 at NHTSANHTSA communication ID: 10111904
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have heated seats inoperative. Technician may find Diagnostic Trouble Code U0209 in the Heater-Vent-Air Conditioning. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER · SEATS.
Source record 10111904 at NHTSANHTSA communication ID: 10111894
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111894 at NHTSANHTSA communication ID: 10111891
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 3.91 gear kit part number 22813040 the 2013-2014 Chevrolet Camaro equipped with Regular Production Option Code (1LE) placed on a parts restriction though General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
Source components: EQUIPMENT.
Source record 10111891 at NHTSANHTSA communication ID: 10252890
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engineering Information.
Source components: POWER TRAIN:CLUTCH ASSEMBLY.
Source record 10252890 at NHTSANHTSA communication ID: 10250084
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels
Source components: WHEELS.
Source record 10250084 at NHTSANHTSA communication ID: 10246854
NHTSA source summary · Original PDF not reviewed by Recallfolio
Key Off Radio Operation.
Source components: EQUIPMENT:APPLIANCE:TV/RADIO/SPEAKERS.
Source record 10246854 at NHTSANHTSA communication ID: 10246642
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information on Tire Cold Weather Cracking
Source components: TIRES · UNKNOWN OR OTHER.
Source record 10246642 at NHTSANHTSA communication ID: 10246621
NHTSA source summary · Original PDF not reviewed by Recallfolio
Car and Truck Fix it Right the First Time Issues
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10246621 at NHTSANHTSA communication ID: 10246571
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels
Source components: WHEELS.
Source record 10246571 at NHTSANHTSA communication ID: 10190932
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190932 at NHTSANHTSA communication ID: 10190931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190931 at NHTSANHTSA communication ID: 10073360
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10073360 at NHTSANHTSA communication ID: 10070150
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE.
Source record 10070150 at NHTSANHTSA communication ID: 10055115
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: SOME MAY COMPLAIN THAT THE CLUTCH PEDAL WOULD NOT COMPLETELY RETURN TO THE TOP AFTER BEING DEPRESSED. IN ORDER TO DETERMINE THE CAUSE OF THE FAILURE INFORMATION ON THE VEHICLE NEEDS TO BE GATHERED BEFORE ANY ATTEMPT TO REPAIR THE VEHICLE HAS BEEN MADE. *JS
Source components: POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE).
Source record 10055115 at NHTSANHTSA communication ID: 10137784
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
Source components: EQUIPMENT.
Source record 10137784 at NHTSANHTSA communication ID: 10112045
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10112045 at NHTSANHTSA communication ID: 10112031
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio can be turned on after turning the ignition off and opening the driver's door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10112031 at NHTSANHTSA communication ID: 10137781
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137781 at NHTSANHTSA communication ID: 10112022
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10112022 at NHTSANHTSA communication ID: 10112019
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
Source record 10112019 at NHTSANHTSA communication ID: 10061080
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: SUSPENSION.
Source record 10061080 at NHTSANHTSA communication ID: 10112018
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published "Engine Cranks But Does Not Run" diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112018 at NHTSANHTSA communication ID: 10112013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10112013 at NHTSANHTSA communication ID: 10112012
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Electronic Brake Control Module and the Brake Pressure Modulator Valve parts restriction has ended. Dealer can now order the parts directly through your Parts Department without General Motors Technical Assistance Center authorization.
Source components: SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE · SERVICE BRAKES, ELECTRIC · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DIFFERENTIAL PROPORTIONAL VALVE.
Source record 10112012 at NHTSANHTSA communication ID: 10112007
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Service Engine Soon Malfunction Indicator Lamp on and a misfire. Technician may find Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277, P2146, P2149, P2152, P2155, P216A, and or P216D. Technician will need to inspect the fuel injector wiring harness for rub through or internal wire opens. If this concern is found repair or replace the injector harness as needed.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · ENGINE.
Source record 10112007 at NHTSANHTSA communication ID: 10137780
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was provides information for the technician of cold start ticking noises in the engine compartment and may be caused by the fuel pump and/or the fuel injectors and no repairs are needed for a normal condition.
Source components: ENGINE · FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS.
Source record 10137780 at NHTSANHTSA communication ID: 10112000
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
Source record 10112000 at NHTSANHTSA communication ID: 10111997
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
Source components: EQUIPMENT.
Source record 10111997 at NHTSANHTSA communication ID: 10111996
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with a supplement to the Service Information timing procedure for the high feature V-6 engine. Technician will also review the training video on the Common Training Website.
Source components: ENGINE.
Source record 10111996 at NHTSANHTSA communication ID: 10111995
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10111995 at NHTSANHTSA communication ID: 10137777
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10137777 at NHTSANHTSA communication ID: 10137776
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER · POWER TRAIN:CLUTCH ASSEMBLY.
Source record 10137776 at NHTSANHTSA communication ID: 10111986
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER.
Source record 10111986 at NHTSANHTSA communication ID: 10137775
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137775 at NHTSANHTSA communication ID: 10111980
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
Source components: ENGINE.
Source record 10111980 at NHTSANHTSA communication ID: 10111977
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.
Source components: ENGINE.
Source record 10111977 at NHTSANHTSA communication ID: 10137773
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on GM?s policy for comprehensive courtesy transportation to its customers.
Source components: EQUIPMENT.
Source record 10137773 at NHTSANHTSA communication ID: 10137772
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137772 at NHTSANHTSA communication ID: 10190981
NHTSA source summary · Original PDF not reviewed by Recallfolio
Malfunction Indicator Lamp Flashes Due to Engine Misfire On Acceleration, DTC P0300 and/or P0303 Set Condition/Concern Some customers may comment that the Malfunction Indicator Lamp flashes when accelerating from a stop or after a steady cruise. The customer may also note that the engine speed was between 2000-4400 RPM when the light illuminated. Depending on the circumstances, some customers may state that no driveability concerns were present while others may state they had considerable driveability impacts. When checking the vehicle for DTCs, the Engine Control Module (ECM) may report DTC P0300 Engine Misfire Detected and/or P0303 Cylinder 3 Misfire Detected set in history.
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
Source record 10190981 at NHTSANHTSA communication ID: 10190934
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190934 at NHTSANHTSA communication ID: 10190933
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190933 at NHTSANHTSA communication ID: 10073304
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: EQUIPMENT.
Source record 10073304 at NHTSANHTSA communication ID: 10133103
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides directions on submitting different PIRs
Source components: BACK OVER PREVENTION: SENSING SYSTEM: RADAR.
Source record 10133103 at NHTSANHTSA communication ID: 10133098
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10133098 at NHTSANHTSA communication ID: 10133097
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin explains physical damage to radios and IPCs must be reviewed and validated if covered under GM warranty or not.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10133097 at NHTSANHTSA communication ID: 10133094
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides information on Radio Favorites Disappear, HD Audio Concerns Favorites Disappear, HD Audio.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10133094 at NHTSA