Original record summaries, dates and identifiers for this model-year. Records 301–400 of 596, ordered newest first. Dated records on this page: Nov 25, 2013–Nov 28, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Nov 28, 2014Service Bulletin/Repair Instructions
TT4506122
NHTSA communication ID: 10238962
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use the following procedure to diagnose active wheel speed sensor complaints
Source components: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER:SENSOR/SENDING UNIT · SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:BLUETOOTH/WIFI.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (SVM Update Instructions): This document informs when performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Rocker Panel - Front Fender ? Corrosion): This document informs of Corrosion on contact surfaces of the front fender to rocker panel (side member). This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Fuel Additive to Help Prevent Sporadic Misfire Faults): Fuel quality impacts the operating performance, efficiency and service life of the engine. The use of poor quality fuels may result in deposit build up on the fuel injectors and intake valves. This may result in a rough running condition, sporadic misfires, or cold start misfire faults storing in the ECM fault memory. This document informs a Volkswagen approved fuel additive is available to help remove and prevent deposits on fuel injectors and intake valves.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Electro ? Steering - DTC 01309 008 ?No Communication with -J500-? is Stored in the ABS/ESP Module Only): This document informs If, after replacement of the steering rack, fault code 01309 008 is set in the ABS/ESP module only, follow the test plan in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the directions in this document using Vehicle Self Diagnosis in Address Word 44 - Steering Assistance:
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Electric Coolant Fans Continue to Run after Ignition is Switched OFF): This documentation informs it is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications. The production solution to service this issue is that no production change is required.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (2.0L CCTA/CBFA Coolant Leak or Repeat Coolant Leak from the Water Pump Area): Inspect the water pump for signs of contact with engine oil. Engine oil may cause the water pump gasket to swell, which may lead to a coolant leak. This document informs of the precaustions necessary if a water pump replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (ECM Fault P1250 "Fuel Level Too Low" Will Not Clear): This document informs to clear static ECM fault P1250 "Fuel Level Too Low", add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Install a vacuum gauge on the dipstick tube and check crankcase vacuum at idle. Compare to a known good vehicle. If the vacuum reading is lower than the comparison vehicle, visually inspect for oil leaks between the engine and the transmission. Smoke test the crankcase by connecting the EVAP smoke machine to the dipstick tube and inspect for leaks at the rear main seal (this will limit pressure to 2 PSI). DO NOT apply shop air to the dipstick tube or the crankcase. If a rear main seal leak is identified, replace the seal. Once replaced, recheck crankcase vacuum at idle. If low, check for additional oil leaks and verify crankcase breather operation (repairing as necessary). Erase the faults and road test 10 miles to recheck operation.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Air Conditioning, Cleaning of the Refrigerant Circuit): In cases where an air conditioning system component (such as a compressor or other system component) has failed and debris from the compressor or component is circulated throughout the refrigerant circuit, the refrigerant circuit must be cleaned of any and all debris or damage to the replacement components will result. Debris can be dispersed throughout the refrigerant circuit after a/c component damage. In order to maintain A/C operating efficiency, it is important to flush the refrigerant circuit after A/C component repairs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Intake Manifold Faults Stored in ECM Fault Memory issues): This document informs of a failure of Intake manifold causing fault codes to be stored in the ECM. The production solution improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLKSWAGEN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. AN EXTENSION WARRANTY, WITH SPECIFIC CONDITIONS, 10 YRS OR 120,000 MILES,WHICHEVER IS FIRST, HAS BEEN ISSUED FOR EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL INJECTORS. MODEL 2008-2011. *PE
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Comfort Module (J393) or BCM (J519) Replacement): This document informs if a comfort or body control module is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting guided function of either the J393 or J519 or control module OBD of J393 or J519 then selecting adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Secondary Air Injection System Air Flow/Pressure): This document informs the Secondary Air Pressure Sensor may be contaminated by foreign particles during secondary air injection. The production solution for this issue was a new sensor placed in production. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
Source components: SERVICE BRAKES, AIR:SUPPLY:LOW PRESSURE WARNING:SWITCH.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Intake Manifold Fault issues): This document informs of Intake Manifold issues that are recognized in the ECM fault memory. The Production Solution to this issue was an improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The DLC is intended for use with diagnostic scan tools and by emissions testing stations. However, aftermarket devices (i.e., drive data recorders) that connect to the DLC have now become available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Intake Manifold issues): This document informs of a failure of Intake manifold causing fault codes to be stored in the ECM. The fault codes are written in the document. The product solution for this issue an Improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Engine Oils Which Meet Volkswagen Oil Quality Standard): This document informs of a sample list of products generally available in the North American market that meet the Volkswagen Oil Quality Standard
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use the diagram below to test the N75 Solenoid Valve in the event of a turbocharger fault code such as P0299 or P0234. This applies to Mechanical Injection Style Diesel Engines, Pumpe Duse Style Diesel Engines and the new Common Rail Style Diesel Engines.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · FUEL SYSTEM, DIESEL · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When diagnosis on the above engine leads to the testing of the N75, please refer to the picture below. The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips 92006-2014 Vehicles with 2.0T Gasoline Engine - N75 Solenoid Valve Diagnosis): When diagnosis on the above engine leads to the testing of the N75, please refer this document with graphical aid. The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not. Turbocharger fault codes P0299 and P0234 can be diagnosed using this test.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quick Reference Update Guide: This document informs of the corresponding software/hardware and disc availability to the customer concerns about a vehicle
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Electro - Steering issues): If, after replacement of the steering rack, fault code 01309 008 is set in the ABS/ESP module only, follow the test plan in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the directions in this document
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Comfort Module (J393) or BCM (J519) Replacement): This document informs If a comfort or body control module is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting the test plan through GFF or through Vehicle Self Diagnosis in adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Oil Consumption Measurement): Customer states oil consumption is higher than the Volkswagen oil consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owners Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Further factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incorrect torque converter or flywheel/flexplate installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. For the flywheel/flexplate, please be certain the correct shim is installed between it and the crankshaft (reference VWIQ120). When installing a torque converter, press the torque converter hub through the seal as far as the first stop. Turn the torque converter while pushing toward the transmission using light force, until the cut outs in the torque converter hub lock into the pump wheel plate. The torque converter slides in. The torque converter is installed correctly if it is easy to turn by hand and if it fits evenly in the transmission bell housing. Additionally, it should spin freely when the transmission bell housing bolts are torqued to the engine block, prior to installation of the flywheel to converter bolts (reference VWIQ121).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Torque Converter/Flywheel/Flexplate installation): Incorrect torque converter or flywheel/flexplate installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. This document also contains advice on the installation of these devices
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The use of tire dressing gives your tires that shiny finish that completes the image of a clean (new) vehicle. There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Always use a water based product.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (All vehicles-Tire dressing for vehicle detailing): The use of tire dressing gives your tires that shiny finish that completes the image of a clean (new) vehicle. This document informs that The use of non-water based products will increase the risk of causing damage to painted surfaces. The document also gives graphical examples of the dame that can occur if non-water based products are used.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Exterior Lights, Moisture Accumulation): This document informs of the Condensation and or water droplets visible on inside of exterior light lenses. The document also informs how to service the issue.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you have a complaint of DTCs for the low side fuel pressure being out of specification (e.g. P310B), check the fuel pressure with BOTH a mechanical gauge and by the display in Measured Value Block 103. The readings should be 1 bar higher in the MVB due to reading atmospheric pressure + fuel pressure. If the mechanical gauge reading is within specification BUT the MVB 103 reading is not 1 bar higher, check for a possible faulty G410 Low Fuel Pressure sensor.
Source components: SERVICE BRAKES, AIR:SUPPLY:PRESSURE GUAGE · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (2.0L FSI (BPY) Engines - Low Fuel Pressure DTCs (P310B)): This document informs on how to check fuel pressure If you have a complaint of DTCs for the low side fuel pressure being out of specification
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Engine Control Module Fault P130A ?Hide Cylinder?): This document informs that DTC P130A ?Hide Cylinder? indicates that excessive misfiring has occurred. As a result, the ECM has turned off a fuel injector to prevent catalyst damage. To address this fault, diagnose and repair all misfire concerns that are present. Repairing the other faults will resolve the P130A.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quick Reference Update Guide: This document informs of the corresponding software/hardware and disc availability to the customer concerns about a vehicle
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (HVAC, Unpleasant Odor): Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this document can be performed. This document contains the procedure for the VW method to remove musty odors
NHTSA source summary · Original PDF not reviewed by Recallfolio
If the steering rack is replaced on the above models for any reason, it is necessary to replace the steering harness as well. The new harness may be equipped with an extra connector. If all connections are made correctly, then it is necessary to remove that connector and tape the exposed wires back into the harness. Be sure to tape tightly in order to provide a water-tight repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Squeaks, Rattles, Noise, Repair Materials): This doucment contains a list of components and applications developed to repair concerns of squeaks, rattles, noise and trim fit conditions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (HVAC, Unpleasant Odor): Unpleasant odor is coming from Heating and Ventilation system. Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Condensation is a normal characteristic in all A/C systems. If odor is noticeable continue to follow this document. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC? III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN? Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin The use of contaminated gasoline, seasonal fuel changes (summer/winter fuel) or gasoline with a low content of deposit control additives may result in one or more of the following conditions: -Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. -Engine runs rough after cold start. -Excessive engine cranking time. -Stumbles while driving. -Rough engine idle. -Loss of engine performance. -Poor fuel economy. This document informs of the procedure for the vehicle if it is diagnoised with poor quality gas
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin This Technical Bulletin details the general process for carrying out a Software Version Management (SVM) software update for any Technical Bulletin (TSB) / Required Vehicle Update (RVU).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Communication Interruptions Following Door Control Module Replacement): Due to further technical development and releases, the latest generation door control units which are UDS diagnosis compatible are now available as service parts for the A5 Jetta and Jetta Wagon, replacing the previously installed KWP 2000 units. In individual cases, there may be communication problems with the newly installed door control unit during diagnosis and connection (coding, adaption, etc).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Exterior Lights, Moisture Accumulation): Exterior light assemblies (headlights, taillights, fog lights, turn signals) are vented and may collect moisture on their inner surfaces, depending on humidity and other climatic changes. This document discusses necessary to diagnosis, and potential remedy of the issue.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the complete vehicle lock set (all vehicle keys and lock cylinders) for any reason, be aware that the ?Adapt keys? test plan will not allow the new keys to adapt to the vehicle. Instead, perform the test plan for ?New identity?. During this test plan, make the appropriate selection to indicate only the lock set has been replaced, as shown below in figures 1 and 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
To detect which line(s) is inoperative, utilize a volt meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage. Proceed with checking any other lines as necessary. Once the damaged line is identified, repair utilizing the Repair kit by Permatex® ITEM 09117.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION:SWITCH · UNKNOWN OR OTHER · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW:ELECTRICAL HEATING ELEMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Install a vacuum gauge on the dipstick tube and check crankcase vacuum at idle. Compare to a known good vehicle. If the vacuum reading is lower than the comparison vehicle, visually inspect for oil leaks between the engine and the transmission. Smoke test the crankcase by connecting the EVAP smoke machine to the dipstick tube and inspect for leaks at the rear main seal (this will limit pressure to 2 PSI). DO NOT apply shop air to the dipstick tube or the crankcase. If a rear main seal leak is identified, replace the seal.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Heated Rear Window, One or More Lines Inoperative): To detect which line(s) is inoperative, utilize a volt meter to check for 0 V, which will be present after the open in the grid line. This document informs of how to diagnose the issue and tips on servicing the issue
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Lean Fuel Trim Readings): This document informs on the procedure to diagnose for issues with excess fuel trim, and what needs to be serviced
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Lean Fuel Trim Readings): This document informs to recheck the crankcase vacuum at idle. If low, check for additional oil leaks and verify crankcase breather operation (repairing as necessary). Erase the faults and road test 10 miles to recheck operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Rattling Noises from Engine Compartment Area or Exhaust System): Customers may complain of a rattling noise from engine or exhaust area while accelerating from 1800-3000 RPM. In order to complete proper diagnosis and ensure that the noise is coming from the turbocharger use the procedure in this document.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Rattling Noises from Engine Compartment Area or Exhaust System): Customers may complain of a rattling noise from engine or exhaust area while accelerating from 1800-3000 RPM. In order to complete proper diagnosis and ensure that the noise is coming from the turbocharger use the procedure in this document.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.