2007 Saturn OUTLOOK Manufacturer communications & TSBs.Page 6
Original record summaries, dates and identifiers for this model-year. Records 501–600 of 979, ordered newest first. Dated records on this page: Oct 16, 2014–May 6, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 6, 2015Service Bulletin/Repair Instructions
PI1475
NHTSA communication ID: 10113631
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians with information on front engine mount service recommendations.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician when replacing the accessory headrest digital video disc monitor to check the control module manufacture part number. If the control module number is CBX-3010G7GM and a monitor needs to be replaced, the control module will also need to be replaced with the upgraded part number SCBX-3010G7GM to avoid compatibility issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/PONTIAC/SATURN: LOW BEAM HEADLAMP BULB DIAGNOSIS/REPLACEMENT (INSPECT BULB AND CONNECTOR). DOES NOT APPLY TO VEHICLES EQUIPPED WITH HIGH INTENSITY DISCHARGE (HID) LAMPS. DO NOT REPLACE THE ENTIRE HEADLAMP ASSEMBLY FOR THIS CONDITION. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle starts and stalls on the first initial start after the replacement of the Theft Deterrent Module. Technician will need to use the scan tool to check Manufactures Enable Counter. If the number is anything other than zero the Manufactures Enable Counter will need to be reset. To reset the Manufactures Enable Counter counter, the ignition key can be cycled the number equal to the Manufactures Enable Counter counter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 - Suspected Tampering or Vehicle Modifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
14404A - SPECIAL COVERAGE (REVISED TO ADD MODEL YEAR VEHICLES, RPO CODES AND UPDATE WARRANTY TRANSACTION INFORMATION). SOME VEHICLES IDENTIFIED ABOVE AND, EQUIPPED WITH A 6T70 OR 6T75 - 6 SPEED FWD AUTOMATIC TRANSMISSION MAY EXPERIENCE A CRACKED OR FRACTURED WAVE PLATE, RESULTING IN A LOSS OF 3RD, 5TH AND REVERSE GEARS. DEALERS ARE TO REPLACE THE 3RD /5TH / REVERSE CLUTCH PLATE.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
14404 - SPECIAL COVERAGE. SOME VEHICLES IDENTIFIED ABOVE AND, EQUIPPED WITH A 6T70 OR 6T75 - 6 SPEED FWD AUTOMATIC TRANSMISSION MAY EXPERIENCE A CRACKED OR FRACTURED WAVE PLATE, RESULTING IN A LOSS OF 3RD, 5TH AND REVERSE GEARS. DEALERS ARE TO REPLACE THE 3RD /5TH / REVERSE CLUTCH PLATE.
Source components: ENGINE · POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only).
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin communicates Information to technicians on control module Diagnostic Trouble Code(s) (DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2015 model year to repair information on correcting a customer concern of poor, limited, reduced Remote Keyless Entry (RKE) or Remote Vehicle Start (RVS) range.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a diagnostic tip for low line pressure or pressure regulator valve stuck after transmission service pump cover replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining when the protective shipping film is removed from certain vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using Customer Concern Verification Sheets (CCVS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product field action customer reimbursement procedure (U.S. Dealers Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. TECHNICIAN WILL NEED TO DETERMINE WHAT TYPE OF CALL THE CUSTOMER IS HAVING THAT IS UNWANTED. THE VEHICLE MAY RECEIVE AN INCOMING CALL JUST LIKE ANY OTHER PHONE. TYPICALLY THE CUSTOMER WILL HEAR THE PHONE RINGING IN THE VEHICLE. THIS SCENARIO ALSO INCLUDES INCOMING BLUETOOTH CALLS. ONE TYPE OF UNWANTED CALL CAN BE MADE IF THE KEY PAD IS FAULTY THE ONSTAR SYSTEM WILL TRY TO MAKE A BLUE BUTTON CALL FOR SHORTED VOLTAGE IN THE CIRCUITS. THE ONSTAR MODULE COULD HAVE AN INTERNAL FAULT AND PRODUCE A PHONE UNAVAILABLE AUDIO MESSAGE ALSO IT MAY HAVE A DIAGNOSTIC TROUBLE CODE U1500 OR B1000. REFER TO DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODE MAKING SURE TO FOLLOW ANY APPLICABLE BULLETINS OR PRELIMINARY INFORMATION SHEETS. A GREADYH OR GONSTAR READYH AUDIO MESSAGE HEARD WHILE DRIVING. IN SOME CASES IT HAS BEEN FOUND THAT THE CUSTOMER IS INADVERTENTLY PRESSING THE PUSH TO TALK BUTTON ON THE STEERING WHEEL CONTROLS. ON RARE OCCASIONS, OTHER ISSUES IN THE STEERING COLUMN OR STEERING WHEEL CONTROL SYSTEM MAY INDUCE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to replace the power steering cooler. Technician will need to block off the hoses near the cooler connection with appropriate clamps. After the hoses are clamped disconnect the cooler from the lines and remove the cooler. Before installing the new cooler prefill the new cooler on the bench and cap off the pre-filled cooler ends for installation. When the new cooler is installed remove the clamps on the hoses and follow the service information for Power Steering System Bleed Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEP TO REPLACE THE POWER STEERING COOLER. TECHNICIAN WILL NEED TO BLOCK OFF THE HOSES NEAR THE COOLER CONNECTION WITH APPROPRIATE CLAMPS. AFTER THE HOSES ARE CLAMPED DISCONNECT THE COOLER FROM THE LINES AND REMOVE THE COOLER. BEFORE INSTALLING THE NEW COOLER PREFILL THE NEW COOLER ON THE BENCH AND CAP OFF THE PRE-FILLED COOLER ENDS FOR INSTALLATION. WHEN THE NEW COOLER IS INSTALLED REMOVE THE CLAMPS ON THE HOSES AND FOLLOW THE SERVICE INFORMATION FOR POWER STEERING SYSTEM BLEED PROCEDURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have rusty or corroded appearance on the exhaust components. This is a normal condition and these components should not be replaced for this surface or cosmetic corrosion.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to replace the power steering cooler. Technician will need to block off the hoses near the cooler connection with appropriate clamps. After the hoses are clamped disconnect the cooler from the lines and remove the cooler. Before installing the new cooler prefill the new cooler on the bench and cap off the pre-filled cooler ends for installation. When the new cooler is installed remove the clamps on the hoses and follow the service information for Power Steering System Bleed Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
14329A - SPECIAL COVERAGE (REVISED SERVICE PROCEDURE). SOME VEHICLES MAY DEVELOP A POWER STEERING PUMP WEAR CONDITION THAT CAN CAUSE AN INTERMITTENT DROP OF POWER STEERING HYDRAULIC PRESSURE THAT WILL CAUSE REDUCED OR LOSS OF STEERING ASSIST. THE VEHICLE MAY REVERT TO MANUAL STEERING WHICH REQUIRES GREATER DRIVER EFFORT, PARTICULARLY AT LOW VEHICLE SPEEDS. DEALERS ARE TO FLUSH THE POWER STEERING SYSTEM, REPLACE THE POWER STEERING PUMP, AND IF IT HASN'T ALREADY BEEN REPLACED, INSTALL A NEW STEERING GEAR VALVE HOUSING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CHEVROLET/GMC/SATURN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. POWER STEERING PUMP WEAR CONDITION CAUSES AN INTERMITTENT DROP IN HYDRAULIC PRESSURE OF POWER STEERING CAUSING LOSS OR REDUCTION IN STEERING ASSIST. MODEL 2007-2011 ACADIA, 2007-10 OUTLOOK, 2008-11 ENCLAVE, 2009-11 TRAVERSE. *PE UPDATED 1/13/15. *PE
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Service Engine Soon Malfunction Indicator Lamp on and or the battery going dead overnight. Technician may find a 4.1 ampere draw. Technician will need to back out pin 1 of connector 2 at the Body Control Module and see if the draw goes away. If the draw goes away, check for an aftermarket accessory that is improperly wired into circuit 1732.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that will not crank intermittently due to a dead battery. Technician will need to reprogram the Heater-Vent-Air Conditioning control module with the latest calibrations.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: LOW BEAM HEADLAMP BULB DIAGNOSIS/ REPLACEMENT (INSPECT BULB AND CONNECTOR). DO NOT REPLACE THE ENTIRE HEADLAMP ASSEMBLY FOR THIS CONDITION. REPLACE THE BULB AND INSPECT THE CONNECTOR. *JS UPDATED 4/7/15. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Power Rear Lift-gate may reverse when closing. Technician will need to remove the lift-gate sill plate and cycle the power lift-gate closed to see if the concern still exists. If the concern is corrected, properly install the lift-gate sill plate. Technician will also need to inspect the lift-gate weather-strip seal for being fully installed on the body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and now is refered to Article 3.2.9 of the 1st addition manual for details of Technician Identification and Accounting of Labor Time
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.